Stiffness Behavior and Micromechanical Modeling of Asphalt Mastic Composed of Different Fillers
Publication: Journal of Materials in Civil Engineering
Volume 34, Issue 8
Abstract
Fillers are known as dust fractions in asphalt mixes having a predominant particle size less than 75 micrometer (μm). Typical filler concentration in an asphalt mix varies from 4% to 12% (by aggregate weight). The effects of filler intrinsic properties on mastic behavior can get magnified with the concentration of filler. Thus, in filler-rich mixes like stone matrix asphalt (SMA), the filler characteristics and concentration can be sensitive factors, playing significant roles in the performance of asphalt mastic and mix. The study considered six different types of fillers to capture the effect of filler characteristics on mastic. The mastics were prepared with a constant filler concentration by volume (), which was determined by a typical SMA mix design. The fillers were characterized based on their surface area, size distribution, shape, Rigden voids (RV), clay content, and chemical composition. The filler effects on mastic were evaluated based on the stiffness (complex modulus) and stiffness ratio. The weak correlation observed between the mastic stiffness and the fixed and free binder reveals that the RV and filler fixing factor (FFF) can mislead regarding the stiffening potential of filler material. The surface areas by Brunauer–Emmett–Teller (BET) and Blaine’s methods were insufficient to represent the stiffening potential while the stiffness showed a better correlation with the concentration of finer gradations in the filler evinced by a higher coefficient of (percentage passing 10 μ sieve size) and fineness modulus (FM) parameters. Further, the micromechanics based understanding of mastic behavior explains the mastic stiffening phenomenon as the combined effects of adsorbed asphalt layer thickness and interparticle interaction. The linear relation observed between stiffness ratio and newly derived micromechanism stiffening factor (MMSF) indicates that in filler-rich mastics, the stiffness may be improved with a finer sized filler (lower FM) and higher volume concentration. However, the adsorbed layer thickness didn’t show correlation with any of the filler properties considered. The study recommends a limiting value for mastic stiffness in terms of stiffness ratio which is established based on MMSF factor. A limiting value for stiffness of mastic could be significant to avoid dry mixes and subsequent poor fatigue performance.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors would like to acknowledge Industrial Research & Consultancy Centre (IRCC) and Department of Civil Engineering IIT Bombay for sponsoring a project 13IRCCSG002, through which a dynamic shear rheometer (DSR) instrument was purchased and utilized extensively for testing on binder and mastic. Also, the authors would like to acknowledge funding support from the Department of Science and Technology (DST), India for sponsored Project No. SR/FST/ETII-056/2013, through which Superpave gyratory compactor equipment was purchased and used for mix design in the current study. In addition, the authors also acknowledge advance testing facility support from the Sophisticated Analytical Instrument Facility (SAIF) at IIT Bombay.
References
AASHTO. n.d. Standard specification for designing stone matrix asphalt. AASHTO MP8. Washington, DC: AASHTO.
Anderson, D. A., H. U. Bahia, and R. Dongre. 1992. “Rheological properties of mineral filler-asphalt mastics and its importance to pavement performance.” In Effects of aggregates and mineral fillers on asphalt mixture performance, Geotechnical Special Publication 1147, 131–153. Reston, VA: ASCE.
Anderson, D. A., and W. H. Goetz. 1973. Mechanical behavior and reinforcement of mineral filler-asphalt mixtures. West Lafayette, IN: Purdue Univ.
Antunes, V., A. C. Freire, L. Quaresma, and R. Micaelo. 2016. “Effect of the chemical composition of fillers in the filler–bitumen interaction.” Constr. Build. Mater. 104 (Feb): 85–91. https://doi.org/10.1016/j.conbuildmat.2015.12.042.
Arvaniti, E. C., M. C. Juenger, S. A. Bernal, J. Duchesne, L. Courard, S. Leroy, and N. De Belie. 2015. “Determination of particle size, surface area, and shape of supplementary cementitious materials by different techniques.” Mater. Struct. 48 (11): 3687–3701. https://doi.org/10.1617/s11527-014-0431-3.
Asphalt Institute. 2014. Mix design methods for asphalt concrete and other hot-mix types: Manual series No. 2 (MS-2). 7th ed. Lexington, KY: Asphalt Institute.
ASTM. 2009. Standard test method for methylene blue index of clay. ASTM C837-09. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard test method for determining the rheological properties of asphalt binder using a dynamic shear rheometer. West Conshohocken, PA: ASTM.
Awed, A. M., E. W. Tarbay, S. M. El-Badawy, and A. M. Azam. 2020. “Performance characteristics of asphalt mixtures with industrial waste/by-product materials as mineral fillers under static and cyclic loading.” Road Mater. Pavement Des.23 (2): 1–23. https://doi.org/10.1080/14680629.2020.1826347.
Bahia, H., I. L. Al-Qadi, A. F. Faheem, E. Fini, H. Wen, and S. Desouky. 2007. NCHRP Project 9-45: Test methods and specification criteria for mineral filler used in HMA. Washington, DC: Transportation Research Board of the National Academies.
Bryant, P. 2005. “Filler: Is it ‘fixing’ your binder?” In Proc., AAPA Pavements Industry Conf., 2005. Port Melbourne, VIC, Australia: Australian Asphalt Pavement Association (AAPA).
Buttlar, W. G., D. Bozkurt, G. G. Al-Khateeb, and A. S. Waldhoff. 1999. “Understanding asphalt mastic behavior through micromechanics.” Transp. Res. Rec. 1681 (1): 157–169. https://doi.org/10.3141/1681-19.
CEN (European Committee for Standardization). 2002. Aggregates for bituminous mixtures and surface treatments for roads, airfields, and other trafficked areas. EN 13043. Brussels, Belgium: CEN.
Cooley, L. A., et al. 1998. “Characterization of asphalt-filler mortars with superpave binder tests.” J. Assoc. Asphalt Paving Technol. 67: 42–56.
Faheem, A. F., and H. U. Bahia. 2010. “Modelling of asphalt mastic in terms of filler-bitumen interaction.” Road Mater. Pavement Des. 11 (1): 281–303. https://doi.org/10.1080/14680629.2010.9690335.
Faheem, A. F., H. U. Bahia, S. H. Yang, and I. L. Al-Qadi. 2010. “Evaluation of Rigden fractional voids test method and the relation to mastic viscosity.” J. Assoc. Asphalt Paving Technol. 79: 1–25.
Guo, M., A. Bhasin, and Y. Tan. 2017a. “Effect of mineral fillers adsorption on rheological and chemical properties of asphalt binder.” Constr. Build. Mater. 141 (Jun): 152–159. https://doi.org/10.1016/j.conbuildmat.2017.02.051.
Guo, M., and Y. Tan. 2021. “Interaction between asphalt and mineral fillers and its correlation to mastics’ viscoelasticity.” Int. J. Pavement Eng. 22 (1): 1–10. https://doi.org/10.1080/10298436.2019.1575379.
Guo, M., Y. Tan, J. Yu, Y. Hou, and L. Wang. 2017b. “A direct characterization of interfacial interaction between asphalt binder and mineral fillers by atomic force microscopy.” Mater. Struct. 50 (2): 1–11. https://doi.org/10.1617/s11527-017-1015-9.
Harris, B., and K. Stuart. 1995. “Analysis of mineral fillers and mastics used in stone matrix asphalt.” J. Assoc. Asphalt Paving Technol. 64 (Mar): 54–95.
Heukelom, W., and P. W. O. Wijga. 1971. “Viscosity of dispersions as governed by concentration and rate of shear.” J. Assoc. Asphalt Paving Technol. 40: 418–437.
IRC (Indian Roads Congress). 2010. Guidelines on use of polymer and rubber modified bitumen in road construction. New Delhi, India: IRC.
IRC (Indian Roads Congress). 2018. Guidelines for the design of flexible pavements. New Delhi, India: IRC.
Kandhal, P., C. Lynn, and F. Parker. 1998. “Characterization tests for mineral fillers related to performance of asphalt paving mixtures.” Transp. Res. Rec. 1638 (1): 101–110. https://doi.org/10.3141/1638-12.
Kandhal, P. S. 1981. “Evaluation of baghouse fines in bituminous paving mixtures (with discussion).” In Vol. 50 of Proc., Association of Asphalt Paving Technologists. Washington, DC: Transportation Research Board.
Kavussi, A., and R. G. Hicks. 1997. “Properties of bituminous mixtures containing different fillers.” J. Assoc. Asphalt Paving Technol. 66: 153–186.
Little, D. N., D. H. Allen, and A. Bhasin. 2018. Modeling and design of flexible pavements and materials. Berlin: Springer.
Macht, F., K. Eusterhues, G. J. Pronk, and K. U. Totsche. 2011. “Specific surface area of clay minerals: Comparison between atomic force microscopy measurements and bulk-gas () and-liquid (EGME) adsorption methods.” Appl. Clay Sci. 53 (1): 20–26. https://doi.org/10.1016/j.clay.2011.04.006.
Mogawer, W. S., and K. D. Stuart. 1996. “Effects of mineral fillers on properties of stone matrix asphalt mixtures.” Transp. Res. Rec. 1530 (1): 86–94. https://doi.org/10.1177/0361198196153000111.
MoRTH (Ministry of Road Transport and Highways). 2013. “Specifications for road and bridge works.” In Indian roads congress. New Delhi, India: MoRTH.
Nikolaides, A. 2014. Highway engineering: Pavements, materials and control of quality. Boca Raton, FL: CRC Press.
Rigden, P. J. 1947. “The use of fillers in bituminous road surfacings. A study of filler-binder systems in relation to filler characteristics.” J. Soc. Chem. Ind. 66 (9): 299–309. https://doi.org/10.1002/jctb.5000660902.
Shashidhar, N., and P. Romero. 1998. “Factors affecting the stiffening potential of mineral fillers.” Transp. Res. Rec. 1638 (1): 94–100. https://doi.org/10.3141/1638-11.
Singh, D., V. Mishra, S. B. Girimath, A. K. Das, and B. Rajan. 2019a. “Evaluation of rheological and moisture damage properties of crumb rubber–modified asphalt binder.” Adv. Civ. Eng. Mater. 8 (1): 477–496. https://doi.org/10.1520/ACEM20190045.
Singh, D., B. Rajan, and H. G. Guta. 2019b. “Effects of aggregate shape on performance of gravel-aggregate hot-mix asphalt using digital image-based approach.” J. Mater. Civ. Eng. 31 (11): 04019260. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002895.
Singh, D., B. Showkat, and B. Rajan. 2020a. “Effects of amine and silane antistripping agents on rheological behavior of crumb rubber modified binder at high and low temperature.” Adv. Civ. Eng. Mater. 9 (1): 387–410. https://doi.org/10.1520/ACEM20190226.
Singh, D., B. Showkat, B. Rajan, and A. Shah. 2020b. “Rheological interference of amine and silane-based antistripping agents on crumb rubber–modified binder.” J. Mater. Civ. Eng. 32 (2): 04019347. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003004.
Tadros, T. F. 2010. Rheology of dispersions: Principles and applications. New York: Wiley.
Tunnicliff, D. G. 1962. “A review of mineral filler.” J. Assoc. Asphalt Paving Technol. 31: 118–150.
Wang, H., I. L. Al-Qadi, A. F. Faheem, H. U. Bahia, S. Yang, and G. H. Reinke. 2011. “Effect of mineral filler characteristics on asphalt mastic and mixture rutting potential.” Transp. Res. Rec. 2208 (1): 33–39. https://doi.org/10.3141/2208-05.
Wang, T., T. Ishida, and R. Gu. 2018. “A comparison of the specific surface area of fly ash measured by image analysis with conventional methods.” Constr. Build. Mater. 190 (Nov): 1163–1172. https://doi.org/10.1016/j.conbuildmat.2018.09.131.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Aug 17, 2021
Accepted: Dec 9, 2021
Published online: May 25, 2022
Published in print: Aug 1, 2022
Discussion open until: Oct 25, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Erxin Li, Xiangyu Zhang, Liyong Wang, Rui Wang, Wei Zhang, Chengqin Chen, Wengang Zhang, Performance of Asphalt Mastic and Asphalt Mixture with Harmless Municipal Solid Waste Incineration Fly Ash, Buildings, 10.3390/buildings13020498, 13, 2, (498), (2023).
- Xiaobing Chen, Wei Wen, Jianguang Zhou, Xiaolong Zhou, Yunfeng Ning, Zhongshan Liang, Zhenyu Ma, Research on the Interaction Capability and Microscopic Interfacial Mechanism between Asphalt-Binder and Steel Slag Aggregate-Filler, Coatings, 10.3390/coatings12121871, 12, 12, (1871), (2022).