Test of Dynamic Mechanical Properties of Ambient-Cured Geopolymer Concrete Using Split Hopkinson Pressure Bar
Publication: Journal of Materials in Civil Engineering
Volume 34, Issue 2
Abstract
The application of geopolymer concrete (GPC) in construction could reduce a large amount of carbon dioxide () emission, which is greatly beneficial to environmental sustainability. Structures made of GPC might be subjected to extreme loading such as impact and blast loads. Therefore, a good understanding of the dynamic properties of GPC is essential to provide reliable predictions of performance of GPC structures subjected to dynamic loading. This study presents an experimental investigation on the dynamic compressive and splitting tensile properties of ambient-cured GPC using split Hopkinson pressure bar (SHPB), with the strain rate up to for dynamic compression and for dynamic splitting tension. The failure mode and damage progress of GPC specimens, energy absorption, and dynamic increase factor (DIF) were studied. Test results showed that ambient-cured GPC exhibited strain rate sensitivity. The compressive and splitting tensile DIFs increased with the strain rate and the ambient-cured GPC with lower quasi-static compressive strength exhibited higher DIFs under both dynamic compression and splitting tension. Empirical formulas were proposed to predict the DIF of ambient-cured GPC. Furthermore, the specific energy absorption of ambient-cured GPC under dynamic compression increased approximately linearly with the strain rate.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or codes that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The authors acknowledge the financial support from the Australian Research Council (ARC) via Australian Laureate Fellowship (FL180100196).
References
Al-Salloum, Y., T. Almusallam, S. M. Ibrahim, H. Abbas, and S. Alsayed. 2015. “Rate dependent behavior and modeling of concrete based on SHPB experiments.” Cem. Concr. Compos. 55 (Jan): 34–44. https://doi.org/10.1016/j.cemconcomp.2014.07.011.
ASTM. 2014. Standard test method for static modulus of elasticity and Poisson’s ratio of concrete in compression. West Conshohocken, PA: ASTM.
Brara, A., and J. R. Klepaczko. 2006. “Experimental characterization of concrete in dynamic tension.” Mech. Mater. 38 (3): 253–267. https://doi.org/10.1016/j.mechmat.2005.06.004.
CEB (Comité Euro-International du Béton). 1993. “CEB-FIP model code 1990: Design code.” In Comite Euro International du Beton, 51–59. London: Thomas Telford.
Chen, J. Y., Z. X. Zhang, H. W. Dong, and J. Zhu. 2011. “Experimental study on dynamic damage evolution of concrete under multi-axial stresses.” Eng. Fail. Anal. 18 (7): 1784–1790. https://doi.org/10.1016/j.engfailanal.2011.04.006.
Deb, P. S., P. Nath, and P. K. Sarker. 2014. “The effects of ground granulated blast-furnace slag blending with fly ash and activator content on the workability and strength properties of geopolymer concrete cured at ambient temperature.” Mater. Des. 62 (1): 32–39. https://doi.org/10.1016/j.matdes.2014.05.001.
Diaz-Loya, E. I., E. N. Allouche, and S. Vaidya. 2011. “Mechanical properties of fly-ash-based geopolymer concrete.” ACI Mater. J. 108 (3): 300.
Feng, K. N., D. Ruan, Z. Pan, F. Collins, Y. Bai, C. M. Wang, and W. H. Duan. 2014. “Effect of strain rate on splitting tensile strength of geopolymer concrete.” Mag. Concr. Res. 66 (16): 825–835. https://doi.org/10.1680/macr.13.00322.
Feng, K. N., D. Ruan, Z. Pan, F. Collins, Y. Bai, C. M. Wang, and W. H. Duan. 2015. “Mechanical behavior of geopolymer concrete subjected to high strain rate compressive loadings.” Mater. Struct. 48 (3): 671–681. https://doi.org/10.1617/s11527-014-0322-7.
Ganesan, N., R. Abraham, S. D. Raj, and D. Sasi. 2014. “Stress–strain behaviour of confined Geopolymer concrete.” Constr. Build. Mater. 73 (Apr): 326–331. https://doi.org/10.1016/j.conbuildmat.2014.09.092.
Gao, Y., J. Xu, E. Bai, X. Luo, J. Zhu, and L. Nie. 2015. “Static and dynamic mechanical properties of high early strength alkali activated slag concrete.” Ceram. Int. 41 (10): 12901–12909. https://doi.org/10.1016/j.ceramint.2015.06.131.
Grote, D. L., S. W. Park, and M. Zhou. 2001. “Dynamic behavior of concrete at high strain rates and pressures: I. Experimental characterization.” Int. J. Impact Eng. 25 (9): 869–886. https://doi.org/10.1016/S0734-743X(01)00020-3.
Hao, Y., and H. Hao. 2013. “Dynamic compressive behaviour of spiral steel fibre reinforced concrete in split Hopkinson pressure bar tests.” Constr. Build. Mater. 48 (12): 521–532. https://doi.org/10.1016/j.conbuildmat.2013.07.022.
Hao, Y., H. Hao, and Z.-X. Li. 2010. “Numerical analysis of lateral inertial confinement effects on impact test of concrete compressive material properties.” Int. J. Protective Struct. 1 (1): 145–167. https://doi.org/10.1260/2041-4196.1.1.145.
Heah, C. Y., H. Kamarudin, A. M. Mustafa Al Bakri, M. Bnhussain, M. Luqman, I. Khairul Nizar, C. M. Ruzaidi, and Y. M. Liew. 2012. “Study on solids-to-liquid and alkaline activator ratios on kaolin-based geopolymers.” Constr. Build. Mater. 35 (Jan): 912–922. https://doi.org/10.1016/j.conbuildmat.2012.04.102.
Huang, Z., W. Chen, H. Hao, Z. Chen, T. M. Pham, T. T. Tran, and M. Elchalakani. 2021a. “Flexural behaviour of ambient cured geopolymer concrete beams reinforced with BFRP bars under static and impact loads.” Compos. Struct. 261 (Apr): 113282. https://doi.org/10.1016/j.compstruct.2020.113282.
Huang, Z., W. Chen, H. Hao, Z. Chen, T. M. Pham, T. T. Tran, and M. Elchalakani. 2021b. “Shear behaviour of ambient cured geopolymer concrete beams reinforced with BFRP bars under static and impact loads.” Eng. Struct. 231 (1): 111730. https://doi.org/10.1016/j.engstruct.2020.111730.
Khan, M. Z. N., Y. Hao, and H. Hao. 2019. “Mechanical properties and behaviour of high-strength plain and hybrid-fiber reinforced geopolymer composites under dynamic splitting tension.” Cem. Concr. Compos. 104 (Nov): 103343. https://doi.org/10.1016/j.cemconcomp.2019.103343.
Khan, M. Z. N., Y. Hao, H. Hao, and F. U. A. Shaikh. 2018. “Experimental evaluation of quasi-static and dynamic compressive properties of ambient-cured high-strength plain and fiber reinforced geopolymer composites.” Constr. Build. Mater. 166 (Sep): 482–499. https://doi.org/10.1016/j.conbuildmat.2018.01.166.
Kim, K.-M., S. Lee, and J.-Y. Cho. 2019. “Effect of maximum coarse aggregate size on dynamic compressive strength of high-strength concrete.” Int. J. Impact Eng. 125 (Mar): 107–116. https://doi.org/10.1016/j.ijimpeng.2018.11.003.
Li, N., C. Shi, Z. Zhang, H. Wang, and Y. Liu. 2019. “A review on mixture design methods for geopolymer concrete.” Composites Part B 178 (Dec): 107490. https://doi.org/10.1016/j.compositesb.2019.107490.
Li, Q. M., Y. B. Lu, and H. Meng. 2009. “Further investigation on the dynamic compressive strength enhancement of concrete-like materials based on split Hopkinson pressure bar tests. Part II: Numerical simulations.” Int. J. Impact Eng. 36 (12): 1335–1345. https://doi.org/10.1016/j.ijimpeng.2009.04.010.
Li, Q. M., and H. Meng. 2003. “About the dynamic strength enhancement of concrete-like materials in a split Hopkinson pressure bar test.” Int. J. Solids Struct. 40 (2): 343–360. https://doi.org/10.1016/S0020-7683(02)00526-7.
Li, W. M., and J. Y. Xu. 2009a. “Impact characterization of basalt fiber reinforced geopolymeric concrete using a 100-mm-diameter split Hopkinson pressure bar.” Mater. Sci. Eng. Struct. Mater. 513 (14): 145–153. https://doi.org/10.1016/j.msea.2009.02.033.
Li, W. M., and J. Y. Xu. 2009b. “Mechanical properties of basalt fiber reinforced geopolymeric concrete under impact loading.” Mater. Sci. Eng. 505 (1–2): 178–186. https://doi.org/10.1016/j.msea.2008.11.063.
Li, X., Y. Zhang, C. Shi, and X. Chen. 2020. “Experimental and numerical study on tensile strength and failure pattern of high performance steel fiber reinforced concrete under dynamic splitting tension.” Constr. Build. Mater. 259 (Oct): 119796. https://doi.org/10.1016/j.conbuildmat.2020.119796.
Li, Z., W. Chen, H. Hao, M. Z. N. Khan, and T. M. Pham. 2021. “Dynamic compressive properties of novel lightweight ambient-cured EPS geopolymer composite.” Constr. Build. Mater. 273 (Mar): 122044. https://doi.org/10.1016/j.conbuildmat.2020.122044.
Lindholm, U. 1964. “Some experiments with the split hopkinson pressure bar∗.” J. Mech. Phys. Solids 12 (5): 317–335. https://doi.org/10.1016/0022-5096(64)90028-6.
Luo, X., and J.-Y. Xu. 2013. “Dynamic splitting-tensile testing of highly fluidised geopolymer concrete.” Mag. Concr. Res. 65 (14): 837–843. https://doi.org/10.1680/macr.12.00172.
Luo, X., J.-Y. Xu, E.-L. Bai, and W. Li. 2013. “Research on the dynamic compressive test of highly fluidized geopolymer concrete.” Constr. Build. Mater. 48 (Nov): 166–172. https://doi.org/10.1016/j.conbuildmat.2013.06.035.
Luo, X., J.-Y. Xu, W. Li, and E. Bai. 2014. “Effect of alkali-activator types on the dynamic compressive deformation behavior of geopolymer concrete.” Mater. Lett. 124 (2): 310–312. https://doi.org/10.1016/j.matlet.2014.03.102.
Lv, T. H., X. W. Chen, and G. Chen. 2017. “Analysis on the waveform features of the split Hopkinson pressure bar tests of plain concrete specimen.” Int. J. Impact Eng. 103 (May): 107–123. https://doi.org/10.1016/j.ijimpeng.2017.01.004.
Ma, L., Z. Li, J. Liu, L. Duan, and J. Wu. 2019. “Mechanical properties of coral concrete subjected to uniaxial dynamic compression.” Constr. Build. Mater. 199 (Feb): 244–255. https://doi.org/10.1016/j.conbuildmat.2018.12.032.
Malvar, L. J., and J. E. Crawford. 1998. Dynamic increase factors for concrete. Port Hueneme, CA: Naval Facilities Engineering Service Center.
Nath, P., and P. K. Sarker. 2014. “Effect of GGBFS on setting, workability and early strength properties of fly ash geopolymer concrete cured in ambient condition.” Constr. Build. Mater. 66 (Sep): 163–171. https://doi.org/10.1016/j.conbuildmat.2014.05.080.
Ng, C., U. J. Alengaram, L. S. Wong, K. H. Mo, M. Z. Jumaat, and S. Ramesh. 2018. “A review on microstructural study and compressive strength of geopolymer mortar, paste and concrete.” Constr. Build. Mater. 186 (Oct): 550–576. https://doi.org/10.1016/j.conbuildmat.2018.07.075.
Noushini, A., F. Aslani, A. Castel, R. I. Gilbert, B. Uy, and S. Foster. 2016. “Compressive stress-strain model for low-calcium fly ash-based geopolymer and heat-cured Portland cement concrete.” Cem. Concr. Compos. 73 (Oct): 136–146. https://doi.org/10.1016/j.cemconcomp.2016.07.004.
Pham, T. M., W. Chen, A. M. Khan, H. Hao, M. Elchalakani, and T. M. Tran. 2020a. “Dynamic compressive properties of lightweight rubberized concrete.” Constr. Build. Mater. 238 (Mar): 117705. https://doi.org/10.1016/j.conbuildmat.2019.117705.
Pham, T. M., J. Liu, P. Tran, V.-L. Pang, F. Shi, W. Chen, H. Hao, and T. M. Tran. 2020b. “Dynamic compressive properties of lightweight rubberized geopolymer concrete.” Constr. Build. Mater. 265 (Dec): 120753. https://doi.org/10.1016/j.conbuildmat.2020.120753.
Ren, W., J. Xu, J. Liu, and H. Su. 2015. “Dynamic mechanical properties of geopolymer concrete after water immersion.” Ceram. Int. 41 (9): 11852–11860. https://doi.org/10.1016/j.ceramint.2015.05.154.
Rossi, P. 1991a. “Influence of cracking in the presence of free water on the mechanical behaviour of concrete.” Mag. Concr. Res. 43 (154): 53–57. https://doi.org/10.1680/macr.1991.43.154.53.
Rossi, P. 1991b. “A physical phenomenon which can explain the mechanical behaviour of concrete under high strain rates.” Mater. Struct. 24 (6): 422–424. https://doi.org/10.1007/BF02472015.
Rossi, P., and F. Toutlemonde. 1996. “Effect of loading rate on the tensile behaviour of concrete: Description of the physical mechanisms.” Mater. Struct. 29 (2): 116. https://doi.org/10.1007/BF02486201.
Singh, B., G. Ishwarya, M. Gupta, and S. K. Bhattacharyya. 2015. “Geopolymer concrete: A review of some recent developments.” Constr. Build. Mater. 85 (6): 78–90. https://doi.org/10.1016/j.conbuildmat.2015.03.036.
Standards Australia. 2014a. Methods of testing concrete: Method 2: Preparing concrete mixes in the laboratory. Australia, Sydney: Standards Australia.
Standards Australia. 2014b. Methods of testing concrete.” Method 9: Compressive strength tests-Concrete, Mortar and grout specimens. Australia, Sydney: Standards Australia.
Standards Australia. 2014c. Methods of testing concrete.” Method 10: Determination of indirect tensile strength of concrete cylinders (‘Brazil’ or splitting test). Australia, Sydney: Standards Australia.
Su, H., J. Xu, and W. Ren. 2014. “Mechanical properties of ceramic fiber-reinforced concrete under quasi-static and dynamic compression.” Materials & Design 57 (Sep): 426–434. https://doi.org/10.1016/j.matdes.2013.12.061.
Su, H. Y., J. Y. Xu, and W. B. Ren. 2016. “Mechanical properties of geopolymer concrete exposed to dynamic compression under elevated temperatures.” Ceram. Int. 42 (3): 3888–3898. https://doi.org/10.1016/j.ceramint.2015.11.055.
Tang, Z., W. Li, V. W. Y. Tam, and Z. Luo. 2020. “Investigation on dynamic mechanical properties of fly ash/slag-based geopolymeric recycled aggregate concrete.” Compos. Part B 185 (Mar): 107776. https://doi.org/10.1016/j.compositesb.2020.107776.
Tedesco, J. W., and C. A. Ross. 1993. “Experimental and numerical analysis of high strain rate splitting-tensile tests.” ACI Mater. J. 90 (2): 162–169. https://doi.org/10.14359/4013.
Thomas, R. J., and S. Peethamparan. 2015. “Alkali-activated concrete: Engineering properties and stress–strain behavior.” Constr. Build. Mater. 93 (Sep): 49–56. https://doi.org/10.1016/j.conbuildmat.2015.04.039.
Tran, T. T., T. M. Pham, and H. Hao. 2019. “Experimental and analytical investigation on flexural behaviour of ambient cured geopolymer concrete beams reinforced with steel fibers.” Eng. Struct. 200 (Dec): 109707. https://doi.org/10.1016/j.engstruct.2019.109707.
Trindade, A. C. C., A. A. Heravi, I. Curosu, M. Liebscher, F. de Andrade Silva, and V. Mechtcherine. 2020. “Tensile behavior of strain-hardening geopolymer composites (SHGC) under impact loading.” Cem. Concr. Compos. 113 (Oct): 103703. https://doi.org/10.1016/j.cemconcomp.2020.103703.
Wang, C., W. Chen, H. Hao, S. Zhang, R. Song, and X. Wang. 2018. “Experimental investigations of dynamic compressive properties of roller compacted concrete (RCC).” Constr. Build. Mater. 168 (Mar): 671–682. https://doi.org/10.1016/j.conbuildmat.2018.02.112.
Xie, J., J. Wang, R. Rao, C. Wang, and C. Fang. 2019. “Effects of combined usage of GGBS and fly ash on workability and mechanical properties of alkali activated geopolymer concrete with recycled aggregate.” Composites Part B 164 (11): 179–190. https://doi.org/10.1016/j.compositesb.2018.11.067.
Yin, Z., W. Chen, H. Hao, J. Chang, G. Zhao, Z. Chen, and K. Peng. 2020. “Dynamic compressive test of gas-containing coal using a modified split hopkinson pressure bar system.” Rock Mech. Rock Eng. 53 (2): 815–829. https://doi.org/10.1007/s00603-019-01955-w.
Zhang, M., H. J. Wu, Q. M. Li, and F. L. Huang. 2009. “Further investigation on the dynamic compressive strength enhancement of concrete-like materials based on split Hopkinson pressure bar tests. Part I: Experiments.” Int. J. Impact Eng. 36 (12): 1327–1334. https://doi.org/10.1016/j.ijimpeng.2009.04.009.
Zhong, W., J. Pan, J. Wang, and C. Zhang. 2020. “Size effect in dynamic splitting tensile strength of concrete: Experimental investigation.” Constr. Build. Mater. 270 (Feb): 121449. https://doi.org/10.1016/j.conbuildmat.2020.121449.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Feb 4, 2021
Accepted: Jun 14, 2021
Published online: Nov 25, 2021
Published in print: Feb 1, 2022
Discussion open until: Apr 25, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Zhenpeng Yu, Xiongfei Zhan, Yuanhao Chang, Lu Hai, Experimental Study on Dynamic Fracture Properties of Concrete under Small Eccentricity Loading, Journal of Materials in Civil Engineering, 10.1061/JMCEE7.MTENG-17503, 36, 8, (2024).
- Jianbo Guo, Jinhua Zhang, Haiyan Ma, Hongfa Yu, Zhangyu Wu, Wenliang Han, Ting Liu, Dynamic Behavior of a New Type of Coral Aggregate Concrete: Experimental and Numerical Investigation, Journal of Materials in Civil Engineering, 10.1061/JMCEE7.MTENG-14821, 35, 6, (2023).
- Zhijie Huang, Musaad Zaheer Nazir Khan, Wensu Chen, Hong Hao, Mohamed Elchalakani, Thong M. Pham, Effectiveness of reinforcing methods in enhancing the lateral impact performance of geopolymer concrete column reinforced with BFRP bars, International Journal of Impact Engineering, 10.1016/j.ijimpeng.2023.104544, 175, (104544), (2023).
- Zhihang Wang, Erlei Bai, He Huang, Chaojia Liu, Tengjiao Wang, Dynamic mechanical properties of carbon fiber reinforced geopolymer concrete at different ages, Ceramics International, 10.1016/j.ceramint.2022.09.056, 49, 1, (834-846), (2023).
- Mohamed Elchalakani, Bo Yang, Kuanhong Mao, Thong Pham, Experimental results, Geopolymer Concrete Structures with Steel and FRP Reinforcements, 10.1016/B978-0-443-18876-3.00006-2, (137-342), (2023).
- Xudong Chen, Jin Wu, Kai Shang, Yingjie Ning, Lihui Bai, Investigation of the Deformation and Failure Characteristics of High-Strength Concrete in Dynamic Splitting Tests, International Journal of Concrete Structures and Materials, 10.1186/s40069-022-00548-2, 16, 1, (2022).
- Hongen Zhang, Ting Chyi Jia, Prabir Kumar Sarker, Wensu Chen, Qingyuan Wang, Zhixing Li, Bei He, Zhengwu Jiang, Effect of fibre addition on the static and dynamic compressive properties of ambient-cured geopolymer concrete, Journal of Building Engineering, 10.1016/j.jobe.2022.104991, 58, (104991), (2022).
- Zhijie Huang, Musaad Zaheer Nazir Khan, Wensu Chen, Hong Hao, Yu Wu, Thong M. Pham, Mohamed Elchalakani, Experimental and numerical study of the performance of geopolymer concrete columns reinforced with BFRP bars subjected to lateral impact loading, Construction and Building Materials, 10.1016/j.conbuildmat.2022.129362, 357, (129362), (2022).