Investigation of Time-Dependent Characteristics of EPDM Rubber Gasket Used for Shield Tunnels
Publication: Journal of Materials in Civil Engineering
Volume 33, Issue 9
Abstract
This paper presents a series of experimental investigations on the time-dependent characteristics of ethylene–propylene–diene monomer (EPDM) under various temperatures and strain conditions. The time-dependent mechanical properties including relaxation modulus and creep compliance of EPDM are investigated through short-term experiments. Based on the time-temperature superposition principle (TTSP), a transformation method named as the time-temperature-strain/stress superposition principle (TTSSP) is proposed to obtain the long-term time-dependent characteristics. The master curves of TTSP are obtained via horizontal shifting of the curves of the relaxation modulus or creep compliance with time and the shift factors are fitted by the Williams-Landel-Ferry equation. The results show that TTSSP is suitable to predict the stress relaxation and creep behavior of EPDM. The results show that, after serving for 100 years at 15°C, the relaxation modulus could reduce to 44.7% under 10% strain, whereas the creep compliance would increase to 191.3% under 1 MPa stress.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The research work was funded by “The Pearl River Talent Recruitment Program” in 2019 (Grant No. 2019CX01G338), Guangdong Province and the Research Funding of Shantou University for New Faculty Member (Grant No. NTF19024-2019).
References
Aleksandrov, A. P., and Y. S. Lazurkin. 1940. “A study of polymers. I. Highly elastic deformation of polymers.” Rubber Chem. Technol. 13 (4): 886–898. https://doi.org/10.5254/1.3546566.
Arulrajah, A., S. Perera, Y. C. Wong, S. Horpibulsuk, and F. Maghool. 2020. “Stiffness and flexural strength evaluation of cement stabilized PET blends with demolition wastes.” Constr. Build. Mater. 239 (Apr): 117819. https://doi.org/10.1016/j.conbuildmat.2019.117819.
ASTM. 2005. Standard test method for rubber property. ASTM D2240. West Conshohocken, PA: ASTM.
ASTM. 2006. Standard test methods for vulcanized rubber and thermoplastic elastomers-tension. ASTM D412. West Conshohocken, PA: ASTM.
Brinson, L. C., and T. S. Gates. 1995. “Effects of physical aging on long term creep of polymers and polymer matrix composites.” Int. J. Solids Struct. 32 (6–7): 827–846. https://doi.org/10.1016/0020-7683(94)00163-Q.
Cheng, W. C., L. Wang, Z. F. Xue, J. C. Ni, M. M. Rahman, and A. Arulrajah. 2019. “Lubrication performance of pipejacking in soft alluvial deposits.” Tunnelling Underground Space Technol. 91 (Sep): 102991. https://doi.org/10.1016/j.tust.2019.102991.
Cui, T., Y. J. Chao, and J. W. Van Zee. 2012. “Stress relaxation behavior of EPDM seals in polymer electrolyte membrane fuel cell environment.” Int. J. Hydrogen Energy 37 (18): 13478–13483. https://doi.org/10.1016/j.ijhydene.2012.06.098.
Ding, W., C. Gong, K. M. Mosalam, and K. Soga. 2017. “Development and application of the integrated sealant test apparatus for sealing gaskets in tunnel segmental joints.” Tunnelling Underground Space Technol. 63 (Mar): 54–68. https://doi.org/10.1016/j.tust.2016.12.008.
Disfani, M. M., A. Arulrajah, H. Haghighi, A. Mohammadinia, and S. Horpibulsuk. 2014. “Flexural beam fatigue strength evaluation of crushed brick as a supplementary material in cement stabilized recycled concrete aggregates.” Constr. Build. Mater. 68 (Oct): 667–676. https://doi.org/10.1016/j.conbuildmat.2014.07.007.
Dong, W., J. Li, X. Zhang, and B. Zhang. 2019. “Evolutions of SIFs of concrete under sustained loading by considering the effects of stress relaxations.” J. Mater. Civ. Eng. 31 (12): 04019287. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002949.
Flory, A., and G. B. McKenna. 2004. “Finite step rate corrections in stress relaxation experiments: a comparison of two methods.” Mech. Time-Depend. Mater. 8 (1): 17–37. https://doi.org/10.1023/B:MTDM.0000027681.86865.4a.
Gallegos, C., and M. García-Morales. 2011. “Rheology of polymer-modified bitumens.” In Polymer modified bitumen, 197–237. Cambridge, UK: Woodhead Publishing. https://doi.org/10.1533/9780857093721.2.197.
Guedes, R. M., and J. L. Morais. 2013. “A simple and effective scheme for data reduction of stress relaxation incorporating physical-aging effects: An analytical and numerical analysis.” Polym. Test. 32 (5): 961–971. https://doi.org/10.1016/j.polymertesting.2013.04.009.
Guner, D., and H. Ozturk. 2018. “Creep behaviour investigation of a thin spray-on liner.” Int. J. Rock Mech. Min. Sci. 108 (Aug): 58–66. https://doi.org/10.1016/j.ijrmms.2018.05.007.
Guner, D., and H. Ozturk. 2019. “Experimental and modelling study on nonlinear time-dependent behaviour of thin spray-on liner.” Tunnelling Underground Space Technol. 84 (Feb): 306–316. https://doi.org/10.1016/j.tust.2018.11.037.
Horpibulsuk, S., C. Suksiripattanapong, W. Samingthong, R. Rachan, and A. Arulrajah. 2016. “Durability against wetting–drying cycles of water treatment sludge–fly ash geopolymer and water treatment sludge–cement and silty clay–cement systems.” J. Mater. Civ. Eng. 28 (1): 04015078. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001351.
Hoy, M., S. Horpibulsuk, A. Arulrajah, and A. Mohajerani. 2018. “Strength and microstructural study of recycled asphalt pavement: Slag geopolymer as a pavement base material.” J. Mater. Civ. Eng. 30 (8): 04018177. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002393.
Irfan, M. S., Y. Q. Gill, M. Hashmi, S. Ullah, F. Saeed, and A. A. Qaiser. 2018. “Long-term stress relaxation behavior of Polyaniline-EPDM blends using the time-temperature-strain superposition method.” Mater. Res. Express 6 (2): 025318. https://doi.org/10.1088/2053-1591/aaf06a.
ISO. 2013a. Rubber, vulcanized or thermoplastic—Determination of ageing characteristics by measurement of stress relaxation in tension. ISO 6914-2013. Geneva: ISO.
ISO. 2013b. Rubber, vulcanized or thermoplastic—Determination of tension set under constant elongation, and of tension set, elongation and creep under constant tensile load. ISO 2285-2013. Geneva: ISO.
ISO. 2014. Rubber, vulcanized or thermoplastic, estimation of life-time and maximum temperature of use from an Arrhenius plot. ISO 11346. Geneva: ISO.
Kömmling, A., M. Jaunich, and D. Wolff. 2016. “Revealing effects of chain scission during ageing of EPDM rubber using relaxation and recovery experiment.” Polym. Test. 56 (Dec): 261–268. https://doi.org/10.1016/j.polymertesting.2016.10.026.
Leaderman, H. 1943. Elastic and creep properties of filamentous materials and other high polymers. Washington, DC: Textile Foundation.
Li, G., J. M. Gong, J. Z. Tan, D. S. Zhu, and W. H. Jia. 2019. “Stress relaxation behavior and life prediction of gasket materials used in proton exchange membrane fuel cells.” J. Cent. South Univ. 26 (3): 623–631. https://doi.org/10.1007/s11771-019-4033-7.
Li, X., S. Zhou, H. Di, and P. Wang. 2018. “Evaluation and experimental study on the sealant behaviour of double gaskets for shield tunnel lining.” Tunnelling Underground Space Technol. 75 (May): 81–89. https://doi.org/10.1016/j.tust.2018.02.004.
Liu, Y., and Z. You. 2009. “Determining burger’s model parameters of asphalt materials using creep-recovery testing data.” In Pavements and materials: Modeling, testing, and performance, 26–36. Reston, VA: ASCE. https://doi.org/10.1061/9780784410080.
Long, Y. Y., and Y. Tan. 2020. “Soil arching due to leaking of tunnel buried in water-rich sand.” Tunnelling Underground Space Technol. 95 (Jan): 103158. https://doi.org/10.1016/j.tust.2019.103158.
Luo, R. K., X. Zhou, and J. Tang. 2016. “Numerical prediction and experiment on rubber creep and stress relaxation using time-dependent hyperelastic approach.” Polym. Test. 52 (Jul): 246–253. https://doi.org/10.1016/j.polymertesting.2016.03.026.
Luo, W., C. Wang, X. Hu, and T. Yang. 2012. “Long-term creep assessment of viscoelastic polymer by time-temperature-stress superposition.” Acta Mech. Solida Sin. 25 (6): 571–578. https://doi.org/10.1016/S0894-9166(12)60052-4.
Luo, W. B., T. Q. Yang, and Q. L. An. 2001. “Time-temperature-stress equivalence and its application to nonlinear viscoelastic materials.” Acta Mech. Solida Sin. 14 (3): 195–199.
Lyu, H. M., S. L. Shen, J. Yang, and A. N. Zhou. 2020a. “Risk assessment of earthquake-triggered geohazards surrounding Wenchuan, China.” Nat. Hazards Rev. 21 (3): 05020007. https://doi.org/10.1061/(ASCE)NH.1527-6996.0000375.
Lyu, H. M., S. L. Shen, A. Zhou, and K. L. Chen. 2020b. “Calculation of pressure on the shallow-buried twin-tunnel in layered strata.” Tunneling and Underground Space Technol. 103 (2020): 103465. https://doi.org/10.1016/j.tust.2020.103465.
Ma, X., H. Chen, X. Zhang, M. Xing, and P. Yang. 2019. “Effect of asphalt binder characteristics on filler-asphalt interactions and asphalt mastic creep properties.” J. Mater. Civ. Eng. 31 (8): 04019138. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002773.
Osanaiye, G. J., and K. P. Adewale. 2001. “Creep and recovery of EPDM elastomer using a modified sandwich rheometer.” Polym. Test. 20 (4): 363–370. https://doi.org/10.1016/S0142-9418(00)00044-1.
Papanicolaou, G. C., and S. P. Zaoutsos. 2019. “Viscoelastic constitutive modeling of creep and stress relaxation in polymers and polymer matrix composites.” In Creep and fatigue in polymer matrix composites, 3–59. Cambridge, UK: Woodhead Publishing. https://doi.org/10.1016/B978-0-08-102601-4.00001-1.
Pongsivasathit, S., S. Horpibulsuk, and S. Piyaphipat. 2019. “Assessment of mechanical properties of cement stabilized soils.” Case Stud. Constr. Mater. 11 (Dec): e00301. https://doi.org/10.1016/j.cscm.2019.e00301.
Ren, D. J., S. L. Shen, A. Arulrajah, and W. C. Cheng. 2018a. “Prediction model of TBM disc cutter wear during tunnelling in heterogeneous ground.” Rock Mech. Rock Eng. 51 (11): 3599–3611. https://doi.org/10.1007/s00603-018-1549-3.
Ren, D. J., S. L. Shen, A. Arulrajah, and H. N. Wu. 2018b. “Evaluation of ground loss ratio with moving trajectories induced in double-o-tube (dot) tunnelling.” Can.Geotech. J. 55 (6): 894–902.
Ronan, S., T. Alshuth, S. Jerrams, and N. Murphy. 2007. “Long-term stress relaxation prediction for elastomers using the time–temperature superposition method.” Mater. Des. 28 (5): 1513–1523. https://doi.org/10.1016/j.matdes.2006.03.009.
Saboo, N., A. Mudgal, and A. Singh. 2019. “Using frequency sweep test to predict creep and recovery response of asphalt binders.” J. Mater. Civ. Eng. 31 (6): 04019081. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002707.
Shalabi, F. I., E. J. Cording, and S. L. Paul. 2012. “Concrete segment tunnel lining sealant performance under earthquake loading.” Tunnelling Underground Space Technol. 31 (Sep): 51–60. https://doi.org/10.1016/j.tust.2012.04.006.
Shen, S. L., H. N. Wu, Y. J. Cui, and Z. Y. Yin. 2014. “Long-term settlement behaviour of metro tunnels in the soft deposits of shanghai.” Tunnelling Underground Space Technol. 40 (Feb): 309–323.
Shi, C., C. Cao, M. Lei, L. Peng, and J. Shen. 2015. “Time-dependent performance and constitutive model of EPDM rubber gasket used for tunnel segment joints.” Tunnelling Underground Space Technol. 50 (Aug): 490–498. https://doi.org/10.1016/j.tust.2015.09.004.
Siengchin, S., T. N. Abraham, and J. Karger-Kocsis. 2008. “Structure-stress relaxation relationship in polystyrene/fluorohectorite micro-and nanocomposites.” Mech. Compos. Mater. 44 (5): 495–504. https://doi.org/10.1007/s11029-008-9043-8.
Stephen, R. 2009. A novel approach to predicting the lifetime of elastomers undergoing stress relaxation. Dublin, IR: Technological Univ. Dublin.
Tan, Y., Y. Lu, C. Xu, and D. Wang. 2018. “Investigation on performance of a large circular pit-in-pit excavation in clay-gravel-cobble mixed strata.” Tunnelling Underground Space Technol. 79 (Sep): 356–374. https://doi.org/10.1016/j.tust.2018.06.023.
Tan, Y., B. Wei, Y. Lu, and B. Yang. 2019. “Is basal reinforcement essential for long and narrow subway excavation bottoming out in Shanghai soft clay?” J. Geotech. Geoenviron. Eng. 145 (5): 05019002. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002028.
Wang, Y., Y. Yang, and M. Tao. 2019. “Understanding free volume characteristics of Ethylene-Propylene-Diene Monomer (EPDM) through molecular dynamics simulations.” Materials (Basel) 12 (4): 612. https://doi.org/10.3390/ma12040612.
Wang, Z. N., S. L. Shen, A. Zhou, and H. M. Lyu. 2020a. “Experimental investigation of water-swelling characteristics of polymer materials for tunnel sealing gasket.” Constr. Build. Mater. 256 (Sep): 119473. https://doi.org/10.1016/j.conbuildmat.2020.119473.
Wang, Z. N., S. L. Shen, A. N. Zhou, and Y. S. Xu. 2020b. “Experimental evaluation of aging characteristics of EPDM as a sealant for undersea shield tunnels.” J. Mater. Civ. Eng. 32 (7): 04020182. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003242.
Xu, J., Y. Ju, B. Han, C. Zhou, and J. Zheng. 2013. “Research on relaxation modulus of viscoelastic materials under unsteady temperature states based on TTSP.” Mech. Time-Depend. Mater. 17 (4): 543–556. https://doi.org/10.1007/s11043-012-9203-z.
Yang, C., S. L. Shen, D. W. Hou, S. M. Liao, and D. J. Yuan. 2018. “Material properties of the seal gasket for shield tunnels: A review.” Constr. Build. Mater. 191 (Dec): 877–890. https://doi.org/10.1016/j.conbuildmat.2018.10.021.
Yaowarat, T., S. Horpibulsuk, A. Arulrajah, A. Mohammadinia, and A. Chinkulkijniwat. 2019. “Recycled concrete aggregate modified with polyvinyl alcohol and fly ash for concrete pavement applications.” J. Mater. Civ. Eng. 31 (7): 04019103. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002751.
Yin, Z. Y., and C. S. Chang. 2013. “Stress–dilatancy behavior for sand under loading and unloading conditions.” Int. J. Numer. Anal. Methods Geomech. 37 (8): 855–870. https://doi.org/10.1002/nag.1125.
Yin, Z. Y., M. Karstunen, C. S. Chang, M. Koskinen, and M. Lojander. 2011. “Modeling time-dependent behavior of soft sensitive clay.” J. Geotech. Geoenviron. Eng. 137 (11): 1103–1113. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000527.
Yin, Z. Y., Q. Xu, and C. Yu. 2015a. “Elastic-viscoplastic modeling for natural soft clays considering nonlinear creep.” Int. J. Geomech. 15 (5): A6014001. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000284.
Yin, Z. Y., J. H. Yin, and H. W. Huang. 2015b. “Rate-dependent and long-term yield stress and strength of soft Wenzhou marine clay: Experiments and modeling.” Mar. Georesour. Geotechnol. 33 (1): 79–91. https://doi.org/10.1080/1064119X.2013.797060.
Yin, Z. Y., J. Zhao, and P. Y. Hicher. 2014. “A micromechanics-based model for sand-silt mixtures.” Int. J. Solids Struct. 51 (6): 1350–1363. https://doi.org/10.1016/j.ijsolstr.2013.12.027.
Yoon, S. H., and C. R. Siviour. 2018. “Application of the Virtual Fields Method to a relaxation behaviour of rubbers.” J. Mech. Phys. Solids 116 (Jul): 416–431. https://doi.org/10.1016/j.jmps.2016.09.001.
Zhang, N., J. S. Shen, C. Lin, A. Arulrajah, and J. C. Chai. 2019. “Investigation of a large ground collapse and countermeasures during mountain tunnelling in hangzhou: A case study.” Bull. Eng. Geol. Environ. 78 (2): 991–1003. https://doi.org/10.1007/s10064-017-1098-0.
Zhang, N., J. S. Shen, A. Zhou, and A. Arulrajah. 2017. “Tunneling induced geohazards in mylonitic rock faults with rich groundwater: a case study in Guangzhou.” Tunnelling Underground Space Technol. 70 (APR): 262–273. https://doi.org/10.1016/j.tust.2017.08.016.
Zhang, P., Z. Y. Yin, Y. F. Jin, and T. H. Chan. 2020. “A novel hybrid surrogate intelligent model for creep index prediction based on particle swarm optimization and random forest.” Eng. Geol. 265 (Feb): 105328. https://doi.org/10.1016/j.enggeo.2019.105328.
Zhu, Z., C. Jiang, Q. Cheng, J. Zhang, S. Guo, Y. Xiong, and H. Jiang. 2015. “Accelerated aging test of hydrogenated nitrile butadiene rubber using the time–temperature–strain superposition principle.” RSC Adv. 5 (109): 90178–90183. https://doi.org/10.1039/C5RA18528A.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Aug 12, 2020
Accepted: Jan 13, 2021
Published online: Jul 14, 2021
Published in print: Sep 1, 2021
Discussion open until: Dec 14, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Xue Li, Zibang Gong, Investigation of Long-Term Waterproof Performance and Hardness Change of EPDM Rubber Gasket Used for Shield Tunnels, Journal of Materials in Civil Engineering, 10.1061/JMCEE7.MTENG-16744, 36, 2, (2024).
- Menglim Hoy, Apichat Suddeepong, Suksun Horpibulsuk, Kongsak Akkharawongthattana, Arul Arulrajah, Apinun Buritatum, Jitwadee Horpibulsuk, Ahmad Safuan A. Rashid, Improved Performance of Natural Rubber Latex–Modified Asphalt Concretes with Various Types of Aggregates, Journal of Materials in Civil Engineering, 10.1061/JMCEE7.MTENG-16274, 36, 1, (2024).
- Chenjie Gong, Yuanye Wang, Wenqi Ding, Mingfeng Lei, Chenghua Shi, Waterproof Performance of Sealing Gasket in Shield Tunnel: A Review, Applied Sciences, 10.3390/app12094556, 12, 9, (4556), (2022).
- Yankai Liu, Qingsong Zhang, Rentai Liu, Mengjun Chen, Chunyu Zhang, Xiuhao Li, Weihao Li, Hongbo Wang, Compressive stress-hydrothermal aging behavior and constitutive model of shield tunnel EPDM rubber material, Construction and Building Materials, 10.1016/j.conbuildmat.2021.126298, 320, (126298), (2022).
- Jyotishkumar Parameswaranpillai, C.D. Midhun Dominic, Sanjay Mavinkere Rangappa, Suchart Siengchin, Togay Ozbakkaloglu, Introduction to elastomers, Elastomer Blends and Composites, 10.1016/B978-0-323-85832-8.00002-X, (1-9), (2022).
- Mohammad Javad Azizli, Mohammad Barghamadi, Katayoon Rezaeeparto, Somayeh Parham, Improvement of mechanical, morphological and thermal properties on PP-enriched graphene oxide/PP-g-MA/EPDM blend compatibilized: PP-g-MA compatibilizer and graphene oxide nanofiller role, Journal of Polymer Research, 10.1007/s10965-022-03182-4, 29, 8, (2022).