Abstract
An analytical model was developed to describe the influence of silica fume on the mechanical behavior of ultra-high-performance concrete. The model defines a single parameter, , which estimates the thickness of paste surrounding all inert, unhydrated cement, and unreacted silica fume particles. The model considers adjustments for partially hydrated cement and partially reacted silica fume to model more accurately the total surface area in the system. The adjustments made for partial hydration and reaction enable the model to be applied to both water-starved and water-saturated mixtures. The compressive strengths of 82 UHPC mixtures containing eight different sources of silica fume were compared with model results, and results suggested that increasing paste thickness led to a decrease in the measured compressive strength.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The authors acknowledge Ashley Harmon for assistance with specific surface area measurements for silica fume, Monica Ramsey for assistance with Blaine fineness testing of other materials, and Norman Burgos for help with sample preparation. The work described herein was funded under the US Army Basic Research Program under PE 61102, Project T22, Task 02, Material Modeling for Force Protection, and was managed and executed at the US Army Engineer Research and Development Center. Permission to publish was granted by the Director, Geotechnical and Structures Laboratory.
References
ASTM. 2014a. Standard test method for specific surface area of alumina or quartz by nitrogen adsorption. ASTM C1069-09. West Conshohocken, PA: ASTM.
ASTM. 2014b. Standard test methods for specific gravity of soil solids by water pycnometer. ASTM D854. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard specification for silica fume used in cementitious mixtures. ASTM C1240. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens). ASTM C109/C109M-16a. West Conshohocken, PA: ASTM.
ASTM. 2018a. Standard test methods for chemical analysis of hydraulic cement. ASTM C114. West Conshohocken, PA: ASTM.
ASTM. 2018b. Standard test methods for fineness of hydraulic cement by air-permeability apparatus. ASTM C204-18e1. West Conshohocken, PA: ASTM.
ASTM. 2019. Standard specification for portland cement. ASTM C150. West Conshohocken, PA: ASTM.
Azad, V. J., P. Suraneni, O. B. Isgor, and W. J. Weiss. 2017. “Interpreting the pore structure of hydrating cement phases through a synergistic use of the Powers-Brownyard model, hydration kinetics, and thermodynamic calculations.” Adv. Civ. Eng. Mater. 6 (1): 1–16.
Brouwers, H. J. H. 2004. “The work of Powers and Brownyard revisited: Part 1.” Cem. Concr. Res. 34 (9): 1697–1716. https://doi.org/10.1016/j.cemconres.2004.05.031.
Burroughs, J. F., T. S. Rushing, D. A. Scott, and B. A. Williams. 2016. “Analyzing effets of varied silica fume sources within baseline UHPC.” In Proc., 1st Int. Interactive Symp. on UHPC. Ames, IA: Iowa State Univ.
Graybeal, B., and J. Tanesi. 2007. “Durability of an ultrahigh-performance concrete.” J. Mater. Civ. Eng. 19 (10): 848–854. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:10(848).
Habel, K., M. Viviani, E. Denarié, and E. Brühwiler. 2006. “Development of the mechanical properties of an ultra-high performance fiber reinforced concrete (UHPFRC).” Cem. Concr. Res. 36 (7): 1362–1370. https://doi.org/10.1016/j.cemconres.2006.03.009.
Li, L. G., and A. K. Kwan. 2013. “Concrete mix design based on water film thickness and paste film thickness.” Cem. Concr. Compos. 39 (May): 33–42. https://doi.org/10.1016/j.cemconcomp.2013.03.021.
Lura, P., O. M. Jensen, and K. van Breugel. 2003. “Autogenous shrinkage in high-performance cement paste: An evaluation of basic mechanisms.” Cem. Concr. Res. 33 (2): 223–232. https://doi.org/10.1016/S0008-8846(02)00890-6.
Powers, T. C., and T. L. Brownyard. 1948. “Studies of the physical properties of hardened portland cement paste.” J. Amer. Concr. Inst. 43 (9): 469–504.
Russell, H. G., and B. A. Graybeal. 2013. Ultra-high performance concrete: A state-of-the-art report for the bridge community. McLean, VA: Federal Highway Administration.
Stutzman, P., A. Heckert, A. Tebbe, and S. Leigh. 2014. “Uncertainty in Bogue-calculated phase composition of hydraulic cements.” Cem. Concr. Res. 61–62 (Jul–Aug): 40–48. https://doi.org/10.1016/j.cemconres.2014.03.007.
Wang, X.-Y. 2014. “Properties prediction of ultra high performance concrete uisng blended cement hydration model.” Constr. Build. Mater. 64 (Aug): 1–10. https://doi.org/10.1016/j.conbuildmat.2014.04.084.
Wille, K., and C. Boisvert-Cotulio. 2015. “Material efficiency in the design of ultra-high performance concrete.” Constr. Build. Mater. 86 (Jul): 33–43. https://doi.org/10.1016/j.conbuildmat.2015.03.087.
Wille, K., A. E. Naaman, and G. J. Parra-Montesinos. 2011. “Ultra-high performance concrete with compressive strength exceeding 150 MPa (22 ksi): A simpler way.” ACI Mater. J. 108 (1): 46–54.
Wu, Z., K. H. Khayat, and C. Shi. 2019. “Changes in rheology and mechanical properties of ultra-high performance concrete with silica fume content.” Cem. Concr. Res. 123 (Sep): 105786. https://doi.org/10.1016/j.cemconres.2019.105786.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Mar 11, 2020
Accepted: Jul 23, 2020
Published online: Dec 30, 2020
Published in print: Mar 1, 2021
Discussion open until: May 30, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.