Small-Strain Dynamic Behavior of Sand and Sand–Crumb Rubber Mixture for Different Sizes of Crumb Rubber Particle
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 11
Abstract
This paper investigates the dynamic behavior of local Barak River sand mixed with different sizes of commercially available crumb rubber at low strain conditions. A series of torsional resonant column tests are conducted to determine the dynamic properties of local Barak River sand and sand–crumb rubber mixture (SCRM). It is aimed to study the effect of different influencing parameters such as confining pressure, relative density, and particle size of crumb rubber on the dynamic behavior of local Barak River sand. All the tests have been conducted under three different confining pressures of 50, 100, and 200 kPa. In this study, two types of crumb rubber with different ranges of particle sizes are mixed with the locally available Barak River sand in different percentages by weight. The test result confirms that the shear modulus is directly proportional to relative density and confining pressure. Higher values of shear modulus have been observed for the samples prepared using larger-sized crumb rubber particles. Moreover, the maximum shear modulus value for the larger crumb rubber is observed at a lower percentage of crumb rubber content compared to that for smaller-sized crumb rubber.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published paper.
Acknowledgments
The authors would like to acknowledge the support obtained from the Center for Testing and Consultancy (CTC) Laboratory at the National Institute of Technology Silchar, India. All the experiments with resonant column apparatus were conducted in CTC laboratory, NIT Silchar.
References
Ahmed, I., and C. W. Lovell. 1993. “Rubber soils as lightweight geomaterials.” Trans. Res. Rec. 1422 (1): 61–70.
Anastasiadis, A., K. Senetakis, K. Pitilakis, C. Gargala, and I. Karakasi. 2011. “Dynamic behavior of sand/rubber mixtures. Part I: Effect of rubber content and duration of confinement on small-strain shear modulus and damping ratio.” J. ASTM Int. 9 (2): 221–247. https://doi.org/10.1520/STP154020120011.
Arulrajah, A., A. Mohammadinia, F. Maghool, and S. Horpibulsuk. 2019. “Tyre derived aggregates and waste rock blends: Resilient moduli characteristics.” Constr. Build. Mater. 201: 207–217.
ASTM. 1992. Standard test methods for modulus and damping of soils by the resonant column method. West Conshohocken, PA: ASTM.
ASTM. 2000. Standard test methods for minimum index density and unit weight of soils and calculation of relative density. West Conshohocken, PA: ASTM.
ASTM. 2018. Standard test method for rubber compounding materials-determination of particle size distribution of recycled vulcanizate particulate rubber. West Conshohocken, PA: ASTM.
Bosscher, P., T. Edil, and S. Kuraoka. 1997. “Design of highway embankments using tyre chips.” J. Geotech. Geoenviron. Eng. 123 (4): 295–304. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:4(295).
Bosscher, P. J., T. B. Edil, and N. Eldin. 1993. “Construction and performance of shredded waste tyre test embankment.” Transp. Res. Rec. 1345 (1): 44–52.
Chattaraj, R., and A. Sengupta. 2016. “Dynamic properties of fly ash.” J. Mater. Civ. Eng. 29 (1): 04016190. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001712.
Chen, A. T. F., and K. H. Stokoe. 1979. Interpretation of strain-dependent modulus and damping from torsional soil tests. Washington, DC: USGS.
Chung, R. M., F. Y. Yokel, and V. P. Drnevich. 1984a. “Evaluation of dynamic properties of sands by resonant column testing.” Geotech. Testing J. 7 (2): 60–69. https://doi.org/10.1520/GTJ10594J.
Chung, R. M., Y. F. Yokel, and Herbert Wechsler. 1984b. “Pore pressure build-up in resonant column test.” J. Geotech. Eng. 110 (2): 247–261. https://doi.org/10.1061/(ASCE)0733-9410(1984)110:2(247).
Dutta, T. T., and S. Sireesh. 2016. “Influence of shear strain on the Poisson’s ratio of clean sands.” Geotech. Geol. Eng. 34 (5): 1359–1373. https://doi.org/10.1007/s10706-016-0047-1.
Edil, T., and P. Bosscher. 1992. Development of engineering criteria for shredded waste tyres in highway applications, final report. Madison, WI: Wisconsin DOT.
Edil, T., and P. Bosscher. 1994. “Engineering properties of waste tyre chips and soil mixtures.” Geotech. Test. J. 17 (4): 453–464. https://doi.org/10.1520/GTJ10306J.
Feng, Z.-Y., and K. Sutter. 2000. “Dynamic properties of granulated rubber/sand mixtures.” Geotech. Test. J. 23 (3): 338–344. https://doi.org/10.1520/GTJ11055J.
Foose, G. J., C. H. Benson, and P. Bosscher. 1996. “Sand reinforced with shredded wastes tires.” J. Geotech. Eng. 122 (9): 760–767. https://doi.org/10.1061/(ASCE)0733-9410(1996)122:9(760).
Hardin, B. 1965. “The nature of damping in sands.” J. Soil Mech. Found. Div. 91: 63–97.
Hardin, B. 1978. “The nature of stress–strain behavior for soils.” In Proc., Earthquake Engineering and Soil Dynamics—ASCE Geotechnical Engineering Division Specialty Conf. Reston, VA: ASCE.
Hardin, B. O., and F. E. Richart. 1963. “Elastic wave velocities in granular soils.” J. Soil Mech. Found. Div. 89 (1): 33–65.
Hazarika H., K. Yasuhara, A. Karmokar, and Y. Mitarai. 2007. “Shaking table test on liquefaction prevention using tyre chips and sand mixture.” In Proc., Int. Workshop on Scrap Tire derived Geomaterials-Opportunities and Challenges, 215–222. London: Taylor & Francis.
Humphrey, D. N., and W. Manion. 1992. “Properties of tire chips for lightweight fill.” Grouting Soil Improv. Geosynthetics 2 (30): 1344–1355.
Indian Standards. 1980. Methods of test for soils, Part 29: Determination of dry density of soils in-place by the core-cutter method. IS 2720. New Delhi, India: Bureau of Indian Standards.
Jakka, R. S., M. Datta, and G. V. Ramana. 2010. “Liquefaction behavior of loose and compacted pond ash.” Soil Dyn. Earthquake Eng. 30 (7): 580–590. https://doi.org/10.1016/j.soildyn.2010.01.015.
Kang, X., B. Bate, R. Chen, W. Yang, and F. Wang. 2019. “Physicochemical and mechanical properties of polymer modified Kaolinite and fly ash Kaolinite soil mixtures.” J. Mater. Civ. Eng. 31 (1): 04019064. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002705.
Kang, X., L. Ge, K-T. Chang, and A. O. Kwok. 2016. “Strain-controlled cyclic simple shear tests on sand with radial strain measurements.” J. Mater. Civ. Eng. 28 (4): 0405169. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001458.
Kang, X., L. Ge, G-C. Kang, and C. Mathews. 2015. “Laboratory investigation on the stiffness, strength, and thermal conductivity of fly ash and lime kiln dust stabilized subgrade materials.” Road Mater. Pavement Des. 16 (4): 1–16.
Kim, B. J., M. Prezzi, and R. Salgado. 2005. “Geotechnical properties of fly and bottom ash mixtures for use in highway embankments.” J. Geotech Geoenviron. Eng. 131 (7): 914–924. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:7(914).
Kim, C. T. M., and M. Novak. 1981. “Dynamic properties of some cohesive soils of Ontario.” Can. Geotech. J. 18 (3): 371–389. https://doi.org/10.1139/t81-044.
Kim, H. K., and J. C. Santamarina. 2008. “Sand–rubber mixtures (large rubber chips).” Can. Geotech. J. 45 (10): 1457–1466. https://doi.org/10.1139/T08-070.
Koutsoftas, D. C., and J. A. Fischer. 1980. “Dynamic properties of two marine clays.” Geotech. Eng. Div. 106 (6): 645–657.
Lee, C., Q. Truong, W. Lee, and J. Lee. 2010. “Characteristics of rubber sand particle mixtures according to size ratio.” J. Mater. Civ. Eng. 22 (4): 323–331. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000027.
Lee, J. H., R. Salgado, A. Bernal, and C. W. Lovell. 1999. “Shredded tires and rubber-sand as lightweight backfill.” J. Geotech. Geoenviron. Eng. 125 (2): 132–141. https://doi.org/10.1061/(ASCE)1090-0241(1999)125:2(132).
Li, B., M. Huang, and X. Zeng. 2016. “Dynamic behavior and liquefaction analysis of recycled-rubber sand mixtures.” J. Mater. Civ. Eng. 28 (11): 04016122 .https://doi.org/10.1061/(ASCE)MT.1943-5533.0001629.
Marcuson, W. F., and H. E. Wahls. 1972. “Time effects on dynamics shear modulus of clay.” J. Soil Mech. Found. Div. 98 (12): 1359–1373.
Masad, E., R. Taha, C. Ho, and T. Papagionnakis. 1996. “Engineering properties of tire/soil mixtures as a lightweight fill material.” Geotech. Test. J. 19 (3): 297–304. https://doi.org/10.1520/GTJ10355J.
Mashiri, M. S., J. S. Viond, and M. N. Sheikh. 2015. “Liquefaction potential and dynamic properties of sand-tire chip (STCH) mixtures.” Geotech. Test. J. 39 (1): 69–79. https://doi.org/10.1520/GTJ20150031.
Mohammadinia, A., M. Disfani, D. Conomy, A. Arulrajah, and S. Darmawan. 2019. “Utilization of alkali-activated fly ash for construction of deep mixed columns in loose sands.” J. Mater. Civ. Eng. 31 (10): 1943–5533.
Pitilakis, K., A. Anastasiadis, D. Pitilakis, K. Trevlopoulos, and K. Senetakis. 2010. Advances in performance-based earthquake engineering, 89–99. Berlin: Springer.
Pitilakis K., K. Trevlopoulos, A. Anastasiadis, and K. Senetakis. 2011. “Seismic response of structures on improved soil.” In Proc., 8th Int. Conf. on Structural Dynamics (EURODYN2011Q2). Leuven, Belgium: Katholieke Universiteit.
Rao, G. V., and R. K. Dutta. 2006. “Compressibility and strength behavior of sand–tyre chip mixtures.” Geotech. Geol. Eng.—Int. J. 24 (3): 711–724. https://doi.org/10.1007/s10706-004-4006-x.
Saxena, K. S., and R. K. Reddy. 1989. “Dynamic moduli and damping ratios for Monterey No. 0 sand by resonant column tests.” Soils Found. 29 (2): 37–51. https://doi.org/10.3208/sandf1972.29.2_37.
Senetakis, K., A. Anastasiadis, K. Pitilakis, and A. Souli. 2012. “Dynamic behavior of sand/rubber mixtures. Part II: Effect of rubber content on -DT curves and volumetric threshold strain.” J. ASTM Int. 9 (2): 1–12. https://doi.org/10.1520/JAI103711.
Senetakis K., A. Anastasiadis, K. Trevlopoulos, and K. Pitilakis. 2009. “Dynamic response of SDOF systems on soil replaced with sand/rubber mixture.” In Proc., ECOMAS Thematic Conf. on Computation Methods in Structural Dynamics and Earthquake Engineering, 22–24. Berlin: Springer.
Tatsuoka, F., T. Iwasaki, K. I Tokida, S. Yasuda, M. Hirose, T. Imai, and M. Kon-No. 1978. “A method for estimating undrained cyclic strength of sandy soils using standard penetration resistance.” Soils Found. 18 (3): 43–58.
Tsang, H. H. 2008. “Seismic isolation by rubber–soil mixtures for developing countries.” Earthquake Eng. Struct. Dyn. 37 (2): 283–303. https://doi.org/10.1002/eqe.756.
Vucetic, M., and R. Dobry. 1991. “Effect of soil plasticity on cyclic response.” J. Geotech. Eng. 117 (1): 89–107. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:1(89).
Wu, W. Y., C. Benda, and R. F. Cauley. 1997. “Triaxial determination of shear strength of tire chips.” J. Geotech. Geoenviron. Eng. 123 (4): 479–482. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:5(479).
Zhang, J., R. Andrus, and C. H. Juang. 2005. “Normalized shear modulus and material damping ratio relationships.” J. Geotech. Geoenviron. Eng. 131 (4): 453–464.
Zornberg, J., A. Carbal, and C. Viratjandr. 2004. “Behaviour of tyre shred–sand mixtures.” Can. Geotech. J. 41 (2): 227–241. https://doi.org/10.1139/t03-086.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Oct 7, 2019
Accepted: Apr 29, 2020
Published online: Aug 23, 2020
Published in print: Nov 1, 2020
Discussion open until: Jan 23, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.