In Situ X-Ray Computed Tomography Experiment on Mesodamage Evolution of Subgrade Bimsoil during Cycle Loading
Publication: Journal of Materials in Civil Engineering
Volume 31, Issue 9
Abstract
This work revealed the mesodamage evolution in blocks-in-matrix soils (bimsoils) under triaixal cyclic loading. Although the macroscopic cyclic stress-strain responses of bimsoil have been well investigated, the mesoscopic damage cracking mechanisms are still not well understood. This work used an artificially prepared bimsoil sample with a rock block percentage (RBP) of 40% (mass ratio) to perform cyclic triaxial testing with a 450-kV industrial X-ray computed tomography (CT) system. For the convenience of damage evolution investigation, the sample was tested with constant stress amplitude and at a low strain level. The mean CT value method and crack extraction method were both used to study the damage evolution during cyclic loading. Results showed that the hysteresis loop on the stress-strain curve had a sparse-dense-sparse pattern caused by the plastic strain accumulation. The damage field distribution in bimsoil is very inhomogeneous and affected by rock blocks. Clear CT images and the CT value of various stages—sample compaction, emergence of a low-density region, crack initiation at rock-soil interface, bifurcation, propagation, and coalescence—were observed. The CT value in the CT images, which is equivalent to sample density, was the most important parameter reflecting the mesoscopic damage evolution. Variation of the CT value in the region of interest (ROI) was influenced by the contact, occlusion, interlock, and separation between the soil matrix and rock blocks. Stress dilatancy caused by the damage cracking behavior had a close link with the evolution of the hysteresis loop, which is controlled by the mesostructural changes during cyclic loading. The paper also reveals the internal relationship between the hysteresis loop area and total crack area during deformation inside the bimsoil sample. The mesodamage evolution of bimsoil under cyclic loading was first documented in this study.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors thank the editors and the anonymous reviewers for their helpful and constructive comments. This study was supported by National Key Technologies Research & Development Program (2018YFC0808402, 2018YFC0604601), the Fundamental Research Funds for the Central Universities (2302017FRF-TP-17-027A1), and the National Natural Science Foundation of China (Grant No. 41502294).
References
Afifipour, M., and P. Moarefvand. 2014. “Failure patterns of geomaterials with block-in-matrix texture: Experimental and numerical evaluation.” Arab. J. Geosci. 7 (7): 2781–2792. https://doi.org/10.1007/s12517-013-0907-4.
Anhdan, L., and J. Koseki. 2004. “Effects of large number of cyclic loading on deformation characteristics of dense granular materials.” Soils Found. 44 (3): 115–123. https://doi.org/10.3208/sandf.44.3_115.
Brennan, A. J., N. I. Thusyanthan, and S. P. G. Madabhushi. 2005. “Evaluation of shear modulus and damping in dynamic centrifuge tests.” J. Geotech. Geoenviron. Eng. 131 (12): 1488–1497. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:12(1488).
Button, E., G. Riedmueller, W. Schubert, K. Klima, and E. Medley. 2004. “Tunnelling in tectonic melanges—accommodating the impacts of geomechanical complexities and anisotropic rock mass fabrics.” Bull. Eng. Geol. Environ. 63 (2): 109–117. https://doi.org/10.1007/s10064-003-0220-7.
Cao, Z., J. Chen, Y. Cai, C. Gu, and J. Wang. 2017. “Effects of moisture content on the cyclic behavior of crushed tuff aggregates by large-scale tri-axial test.” Soil Dyn. Earthquake Eng. 95 (10): 1–8. https://doi.org/10.1016/j.soildyn.2017.01.027.
Cnudde, V., and M. N. Boone. 2013. “High-resolution X-ray computed tomography in geosciences: A review of the current technology and applications.” Earth-Sci. Rev. 123 (1): 1–17. https://doi.org/10.1016/j.earscirev.2013.04.003.
Coli, N., P. Berry, and D. Boldini. 2011. “In situ non-conventional shear tests for the mechanical characterisation of a bimrock.” Int. J. Rock Mech. Min. 48 (1): 95–102. https://doi.org/10.1016/j.ijrmms.2010.09.012.
Higo, Y., F. Oka, T. Sato, Y. Matsushima, and S. Kimoto. 2013. “Investigation of localized deformation in partially saturated sand under triaxial compression using microfocus X-ray CT with digital image correlation.” Soils Found. 53 (2): 181–198. https://doi.org/10.1016/j.sandf.2013.02.001.
Hirono, T., M. Takahashi, and S. Nakashima. 2003. “In situ visualization of fluid flow image within deformed rock by X-ray CT.” Eng. Geol. 70 (1): 37–46. https://doi.org/10.1016/S0013-7952(03)00074-7.
Ishikawa, T., and S. Miura. 2015. “Influence of moving wheel loads on mechanical behavior of submerged granular roadbed.” Soils Found. 55 (2): 242–257. https://doi.org/10.1016/j.sandf.2015.02.002.
Kahraman, S., M. Alber, O. Gunaydin, and M. Fener. 2015. “The usability of the cerchar abrasivity index for the evaluation of the triaxial strength of Misis fault breccia.” Bull. Eng. Geol. Environ. 74 (1): 163–170. https://doi.org/10.1007/s10064-014-0618-4.
Kalender, A., H. Sonmez, E. Medley, C. Tunusluoglu, and K. E. Kasapoglu. 2014. “An approach to predicting the overall strengths of unwelded bimrocks and bimsoils.” Eng. Geol. 183: 65–79. https://doi.org/10.1016/j.enggeo.2014.10.007.
Karpyn, Z. T., A. Alajmi, F. Radaelli, P. M. Halleck, and A. S. Grader. 2009. “X-ray CT and hydraulic evidence for a relationship between fracture conductivity and adjacent matrix porosity.” Eng. Geol. 103 (3–4): 139–145. https://doi.org/10.1016/j.enggeo.2008.06.017.
Kim, C., C. Smell, and E. Medley. 2007. “Shear strength of Franciscan Complex melange as calculated from back analysis of a landslide.” In Proc., 5th Int. Conf. on Case Histories in Geotechnical Engineering, 13–17. Rolla, MO: Missouri Univ. of Science and Technology.
Kong, X., J. Liu, D. Zou, and H. Liu. 2016. “Stress-dilatancy relationship of Zipingpu gravel under cyclic loading in triaxial stress states.” Int. J. Geomech. 16 (4): 04016001. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000584.
Kumar, S. S., A. M. Krishna, and A. Dey. 2017. “Evaluation of dynamic properties of sandy soil at high cyclic strains.” Soil Dyn. Earthquake Eng. 99 (35): 157–167. https://doi.org/10.1016/j.soildyn.2017.05.016.
Lamas-Lopez, F. 2016. “Field and laboratory investigation on the dynamic behavior of conventional railway track-bed materials in the context of traffic upgrade.” Ph.D. thesis, Ecole Nationale des Ponts et Chaussees, Universite Paris-Est.
Lemaitre, J., and J. L. Chaboche. 1990. Mechanics of solid materials. Cambridge, UK: Cambridge University Press.
Lenart, S., J. Koseki, Y. Miyashita, and T. Sato. 2014. “Large-scale triaxial tests of dense gravel material at low confining pressures.” Soils Found. 54 (1): 45–55. https://doi.org/10.1016/j.sandf.2013.12.005.
Lenoir, N., M. Bornert, J. Desrues, P. Bésuelle, and G. Viggiani. 2007. “Volumetric digital image correlation applied to X-ray microtomography images from triaxial compression tests on argillaceous rock.” Strain 43 (3): 193–205. https://doi.org/10.1111/j.1475-1305.2007.00348.x.
Lindquist, E. S. 1994. “The strength and deformation properties of melange.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of California.
Lindquist, E. S., and R. E. Goodman. 1994. “The strength and deformation properties of a physical model mélange.” In Proc., 1st North American Rock Mech. Symp., 843–850. Austin, TX: American Rock Mechanics Association.
Maqbool, S., and J. Koseki. 2010. “Large-scale triaxial tests to study effects of compaction energy and large cyclic loading history on shear behavior of gravel.” Soils Found. 50 (5): 633–644. https://doi.org/10.3208/sandf.50.633.
Medley, E., and E. S. Lindquist. 1995. “The engineering significance of the scale-independence of some Franciscan melanges in California, USA.” In Proc., 35th US Rock Mechanics Symp., edited by J. K. Daemen, and R. A. Schultz, 907–914. Rotterdam, Netherlands: A.A. Balkema.
Medley, E. W., and D. Zekkos. 2011. “Geopractitioner approaches to working with antisocial mélanges.” In Mélanges: Processes of formation and societal significance, edited by J. Wakabayashi, and Y. Dilek, 261–277. Boulder, CO: Geological Society of America.
Menq, F. Y. 2003. “Dynamic properties of sandy and gravelly soils.” Ph.D. thesis, Dept. of Civil, Architectural and Environmental Engineering, Univ. of Texas at Austin.
Modoni, G., J. Koseki, and L. Q. Anh Dan. 2011. “Cyclic stress-strain response of compacted gravel.” Geotechnique 61 (6): 473–485. https://doi.org/10.1680/geot.7.00150.
MWRPRC (Ministry of Water Resources of the People’s Republic of China). 1999. Standard for soil test method. GB/T 50123. Beijing: MWRPRC.
Rücknagel, J., P. Götze, B. Hofmann, and O. Christen. 2013. “The influence of soil gravel content on compaction behavior and pre-compression stress.” Geoderma 209 (12): 226–232. https://doi.org/10.1016/j.geoderma.2013.05.030.
Singh, U. K., and P. J. Digby. 1989. “A continuum damage model for simulation of the progressive failure of brittle rocks.” Int. J. Solids Struct. 25 (6): 647–663. https://doi.org/10.1016/0020-7683(89)90031-0.
Slatalla, N., M. Alber, and S. Kahraman. 2010. “Analyses of acoustic emission response of a fault breccia in uniaxial deformation.” Bull. Eng. Geol. Environ. 69 (3): 455–463. https://doi.org/10.1007/s10064-010-0296-9.
Suiker, A. S., E. T. Selig, and R. Frenkel. 2005. “Static and cyclic triaxial testing of ballast and subballast.” J. Geotech. Geoenviron. Eng. 131 (6): 771–782. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:6(771).
Sun, Q. D., B. Indraratna, and S. Nimbalkar. 2016. “Deformation and degradation mechanisms of railway ballast under high frequency cyclic loading.” J. Geotech. Geoenviron. Eng. 142 (1): 04015056. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001375.
Thakur, P. K., J. S. Vinod, and B. Indraratna. 2013. “Effect of confining pressure and frequency on the deformation of ballast.” Géotechnique 63 (9): 786–790. https://doi.org/10.1680/geot.12.T.001.
Tsiambaos, G. 2010. “Engineering geological behaviour of heterogeneous and chaotic rock masses.” In Proc., 12th Int. Congress. Patras, Greece: Bulletin of the Geological Society of Greece.
Wang, H. L., Y. J. Cui, F. Lamas-Lopez, J. C. Dupla, J. Canou, N. Calon, G. Saussine, P. Aimedieu, and R. P. Chen. 2017a. “Effects of inclusion contents on resilient modulus and damping ratio of unsaturated track-bed materials.” Can. Geotech. J. 54 (12): 1672–1681. https://doi.org/10.1139/cgj-2016-0673.
Wang, Y., C. H. Li, Z. Hou, X. Yi, and X. Wei. 2018a. “In vivo X-ray computed tomography investigations of crack damage evolution of cemented waste rock backfills (CWRB) under uniaxial deformation.” Minerals 8 (11): 539. https://doi.org/10.3390/min8110539.
Wang, Y., C. H. Li, Y. Hu, and Y. Z. Xiao. 2017b. “Optimization of multiple seepage piping parameters to maximize the critical hydraulic gradient in bimsoils.” Water 9 (10): 787. https://doi.org/10.3390/w9100787.
Wang, Y., C. H. Li, and Y. Z. Hu. 2018b. “Use of X-ray computed tomography to investigate the effect of rock blocks on meso-structural changes in soil-rock mixture under triaxial deformation.” Constr. Build. Mater. 164 (31): 386–399. https://doi.org/10.1016/j.conbuildmat.2017.12.173.
Wang, Y., X. Li, R. L. Hu, S. D. Li, and J. Y. Wang. 2015a. “Experimental study of the ultrasonic and mechanical properties of SRM under compressive loading.” Environ. Earth Sci. 74 (6): 5023–5037. https://doi.org/10.1007/s12665-015-4529-x.
Wang, Y., X. Li, Y. F. Wu, and C. Lin. 2015b. “Experimental study on meso-damage cracking characteristics of RSA by CT test.” Environ. Earth Sci. 73 (9): 5545–5558. https://doi.org/10.1007/s12665-014-3808-2.
Wang, Y., X. Li, B. Zhang, and Y. F. Wu. 2014. “Meso-damage cracking characteristics analysis for rock and soil aggregate with CT test.” Sci. China Technol. Sci. 57 (7): 1361–1371. https://doi.org/10.1007/s11431-014-5578-1.
Wang, Y., X. Li, B. Zheng, J. M. He, and S. D. Li. 2016. “Macro-meso failure mechanism of soil-rock mixture at medium strain rates.” Géotech. Lett. 6 (1): 235–243. https://doi.org/10.1680/jgele.15.00118.
Wang, Y., X. Li, B. Zheng, B. Zhang, and J. B. Wang. 2015c. “Real-time ultrasonic experiments and mechanical properties of soil and rock mixture during triaxial deformation.” Géotech. Lett. 5 (4): 281–286. https://doi.org/10.1680/jgele.15.00131.
Wang, Y., and Y. L. Wang. 2017. “Liquefaction characteristics of gravelly soil under cyclic loading with constant strain amplitude by experimental and numerical investigations.” Soil Dyn. Earthquake Eng. 92 (17): 388–396. https://doi.org/10.1016/j.soildyn.2016.10.029.
Xia, J. G., R. L. Hu, and W. Gao. 2017. “Research on large-scale triaxial shear testing of soil rock mixtures containing oversized particles.” [In Chinese.] Chin. J. Rock Mech. Eng. 36 (8): 2031–2039.
Xu, W. J., and R. L. Hu. 2008. “Field horizontal push shear test for mechanical property of soil-rock mixture under cyclic loading.” J. Eng. Geol. 16 (1): 63–70.
Zhang, S., H. Tang, H. Zhan, G. Lei, and H. Cheng. 2015. “Investigation of scale effect of numerical unconfined compression strengths of virtual colluvial–deluvial soil–rock mixture.” Int. J. Rock Mech. Min. Sci. 77 (23): 208–219. https://doi.org/10.1016/j.ijrmms.2015.04.012.
Zhang, Z. L., W. J. Xu, W. Xia, and H. Y. Zhang. 2016. “Large-scale in-situ test for mechanical characterization of soil–rock mixture used in an embankment dam.” Int. J. Rock Mech. Min. Sci. 86 (11): 317–322. https://doi.org/10.1016/j.ijrmms.2015.04.001.
Zhou, X. P., Y. X. Zhang, and Q. L. Ha. 2008. “Real-time computerized tomography (CT) experiments on limestone damage evolution during unloading.” Theor. Appl. Fract. Mech. 50 (1): 49–56. https://doi.org/10.1016/j.tafmec.2008.04.005.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Apr 5, 2018
Accepted: Feb 19, 2019
Published online: Jun 24, 2019
Published in print: Sep 1, 2019
Discussion open until: Nov 24, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.