Abstract
Field-cast cementitious grouts are commonly used for connecting adjacent prefabricated bridge deck elements. These grouts can exhibit high shrinkage levels and are susceptible to premature bond failure at the interface between the precast concrete and connection grout. These actions commonly result in connection cracking, which can lead to serviceability issues in the bridge structure such as reinforcing bar corrosion, leakage, and degradation of structural performance. This study presents a set of potential strategies to enhance the shrinkage properties and bond performance of these grouted connections. The strategies include using advanced materials such as ultra-high performance concrete (UHPC), proper detailing of precast concrete connection surfaces, application of internal curing in connection grouts, and use of interface premoistening. The study includes experiments conducted at both material and component levels. At the material level, these potential improvement strategies were evaluated using standardized shrinkage and bond-strength test methods. To demonstrate the impact on structural performance, some of these strategies were used in a component-level investigation consisting of three large-scale bridge deck connection tests. Experimental results demonstrate that the suggested strategies can reduce shrinkage, enhance bond strength, and improve structural performance of connections.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research presented in this paper was funded by the U.S. Federal Highway Administration. This support is gratefully acknowledged. The publication of this paper does not necessarily indicate approval or endorsement of the findings, opinions, conclusions, or recommendations either inferred or specifically expressed herein by the Federal Highway Administration or the United States Government. This research could not have been completed were it not for the dedicated support of the federal and contract staff associated with the FHWA Structural Concrete Research Program. The authors would also like to thank Mr. Dale Bentz (National Institute of Standards and Technology) for his valuable comments.
References
AASHTO. (2016). LRFD bridge design specifications, Washington, DC.
ASTM. (2013). “Standard test method for tensile strength of concrete surfaces and the bond strength or tensile strength of concrete repair and overlay materials by direct tension (pull-off method).” ASTM C1583/C1583M-13, West Conshohocken, PA.
ASTM. (2014). “Standard test method for autogenous strain of cement paste and mortar.” ASTM C1698-09, West Conshohocken, PA.
ASTM. (2015). “Standard test method for flow of hydraulic cement mortar.” ASTM C1437-15, West Conshohocken, PA.
ASTM. (2016). “Standard test method for time of setting of concrete mixtures by penetration resistance.” ASTM C403/C403M-16, West Conshohocken, PA.
ASTM. (2017a). “Standard specification for lightweight aggregate for internal curing of concrete.” ASTM C1761/C1761M-17, West Conshohocken, PA.
ASTM. (2017b). “Standard test method for length change of hardened hydraulic-cement mortar and concrete.” ASTM C157/C157M-17, West Conshohocken, PA.
Bentz, D. P. (2016). “30 years of imaging and modeling building materials at NBS/NIST: From PIXAR to MICROCHAR.” Imaging of Construction Materials and Geomaterials, LafargeHolcim and Laboratoire Navier, Paris.
Bentz, D. P., Lura, P., and Roberts, J. W. (2005). “Mixture proportioning for internal curing.” Concr. Int., 27(2), 35–40.
Bentz, D. P., and Weiss, W. J. (2011). “Internal curing: A 2010 state-of-the- art review.”, NIST, Gaithersburg, MD.
Bentz, D. P., et al. (2018). “Influence of substrate moisture state and roughness on interface microstructure and bond strength: Slant shear vs. pull-off testing.” Cem. Concr. Compos., 87, 63–72.
Beushausen, H. (2015). “The influence of precast surface moisture condition on overlay bond strength.” Concr. Plant Int., 1, 144–147.
Beushausen, H., Höhlig, B., and Talotti, M. (2017). “The influence of substrate moisture preparation on bond strength of concrete overlays and the microstructure of the OTZ.” Cem. Concr. Res., 92, 84–91.
Bissonnette, B., Vaysburd, A., and Von Fay, K. (2012). Best practices for preparing concrete surfaces prior to repairs and overlays, Denver.
Culmo, M. P. (2009). Connection details for prefabricated bridge elements and systems, Federal Highway Administration, McLean, VA.
Culmo, M. P. (2011). “Accelerated bridge construction: Experience in design, fabrication and erection of prefabricated bridge elements and systems.”, Federal Highway Administration, Washington, DC.
De la Varga, I., and Graybeal, B. A. (2015). “Dimensional stability of grout-type materials used as connections between prefabricated concrete elements.” J. Mater. Civ. Eng., 1–10.
De la Varga, I., and Graybeal, B. A. (2016). “Dimensional stability of grout-type materials used as connections between prefabricated concrete elements.”, Federal Highway Administration, McLean, VA.
Folliard, K. J., and Berke, N. S. (1997). “Properties of high-performance concrete containing shrinkage-reducing admixture.” Cem. Concr. Res., 27(9), 1357–1364.
Garboczi, E. J., and Bentz, D. P. (1991). “Digital simulation of the aggregate-cement paste interfacial zone in concrete.” J. Mater. Res., 6(1), 196–201.
Graybeal, B. (2011). “Fatigue response in bridge deck connection composed of field-cast ultra-high-performance concrete.” Transp. Res. Rec., 2251, 93–100.
Haber, Z. B., Munoz, J. F., De la Varga, I., and Graybeal, B. A. (2017b). “Ultra-high performance concrete for bridge deck overlays.”, Federal Highway Administration, McLean, VA.
Haber, Z. B., Munoz, J. F., and Graybeal, B. A. (2017a). “Field testing of an ultra-high performance concrete overlay.”, Federal Highway Administration, McLean, VA.
ICRI (International Concrete Repair Institute). (2013). “Selecting and specifying concrete surface preparation for sealers, coatings, polymer overlays, and concrete repair.”, Rosemont, IL.
Issa, M. A., Yousif, A. A., Issa, M. A., Kaspar, I. I., and Khayyat, S. Y. (1995). “Field performance of full depth precast concrete panels in bridge deck rehabilitation.” PCI J., 40(3), 82–108.
Lukovic, M., and Ye, G. (2016). “Effect of moisture exchange on interface formation in the repair system studied by X-ray absorption.” Materials, 9(1), 2.
RILEM. (2007). “Internal curing of concrete.”, Paris (in French).
Russel, H. G., and Graybeal, B. A. (2013). “Ultra-high performance concrete: A state-of-the-art report for the bridge community.”, Federal Highway Administration, Washington, DC.
Santos, P. M. D., Julio, E. N. B. S., and Silva, V. D. (2007). “Correlation between concrete-to-concrete bond strength and the roughness of the substrate surface.” Constr. Build. Mater., 21(8), 1688–1695.
Scrivener, K. L., Crumbie, A. K., and Laugesen, P. (2004). “The interfacial transition zone (ITZ) between cement paste and aggregate in concrete.” Interface Sci., 12(4), 411–421.
Silfwerbrand, J., and Paulsson, J. (1998). “Better bonding of bridge deck overlays.” Concr. Int., 20(10), 56–61.
Wille, K., and Boisvert-Cotulio, C. (2013). “Development of non-proprietary ultra-high performance concrete for use in the highway bridge sector.”, National Technical Information Service, Springfield, VA.
Zhu, P., and Ma, Z. J. (2010). “Selection of durable closure pour materials for accelerated bridge construction.” J. Bridge Eng., 695–704.
Zhu, P., Ma, Z. J., and French, C. E. (2012). “Fatigue evaluation of longitudinal U-bar joint details for accelerated bridge construction.” J. Bridge Eng., 201–210.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jun 8, 2017
Accepted: Oct 10, 2017
Published online: Feb 10, 2018
Published in print: Apr 1, 2018
Discussion open until: Jul 10, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.