Effect of Parallel Plate Gap Height on Repeatability in DSR Measurements of Crumb-Rubber Modified Binders
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 8
Abstract
Current Superpave performance grade (PG) grading specification utilizes a dynamic shear rheometer (DSR) at a gap height of 1-mm to determine the high-temperature performance grade of asphalt binders. It has been anticipated that rubber particulates greater than 25% of the gap height may interfere with the measurements, resulting in properties that may not represent the actual crumb rubber binder. Therefore, this study tries to adjust the 1-mm gap height for measuring high-temperature performance properties of crumb rubber binders to minimize the effects of interaction between the asphalt binder and rubber particle on PG grading results. Trial gap heights of 2 and 3 mm were used to test five different crumb rubber modified (CRM) binders. The CRM binders were evaluated using the standard Superpave high-temperature grading test and multiple stress creep and recovery (MSCR) test. Results were analyzed using statistical analysis, and through the comparison with single operator precision statements, where it was shown that higher variability is observed at the 2-mm gap height relative to the 3-mm gap height. Also, the repeatability between replicates was deemed acceptable, particularly for the 3-mm testing gap. Based on the results, a parallel plate gap height of 3 mm was recommended, and modified stress levels and testing temperatures for the MSCR test were proposed.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2009a). “Standard method of test for determining the rheological properties of asphalt binder using a dynamic shear rheometer (DSR).” AASHTO T315, Washington, DC.
AASHTO. (2009b). “Standard method of test for multiple stress creep recovery (MSCR) test of asphalt binder using a dynamic shear rheometer (DSR).” AASHTO TP70, Washington, DC.
AASHTO. (2010a). “Standard specification for performance-graded asphalt binder.” AASHTO M320, Washington, DC.
AASHTO. (2010b). “Standard specification for performance-graded asphalt binder using multiple stress creep recovery (MSCR) test.” AASHTO MP19, Washington, DC.
ASTM. (2008). “Standard test method for determining the rheological properties of asphalt binder using a dynamic shear rheometer.” D7175, West Conshohocken, PA.
ASTM. (2010a). “Standard practice for determining the continuous grading temperatures and continuous grades for PG graded asphalt binders.” D7643, West Conshohocken, PA.
ASTM. (2010b). “Standard test method for multiple stress creep and recovery (MSCR) of asphalt binder using a dynamic shear rheometer.” D7405, West Conshohocken, PA.
ASTM. (2013). “Standard practice for preparing precision and bias statements for test methods for construction materials.” C670, West Conshohocken, PA.
Bahia, H., and Davies, R. (1995). “Factors controlling the effects of crumb rubber on critical properties of asphalt binders.” J. Assoc. Asphalt Paving Technol., 64, 131–143.
Bahia, H., Zhai, H., Zeng, M., Hu, Y., and Turner, P. (2001). “Development of binder specification parameters based on characterization of damage behavior.” Asphalt Paving Technol., 70, 442–470.
Bahia, H. U., and Anderson, D. A. (1995). “Strategic Highway Research Program binder rheological parameters: Background and comparison with conventional properties.” Transp. Res. Rec., 1488, 32–39.
Baumgardner, G., and D’Angelo, J. A. (2012). “Development of a crumb rubber modified (CRM) PG binder specification.” Asphalt Rubber Int. Conf., Consulpav-Consultores E Projectistas De Pavimentos, LDA, Portugal, 22–29.
Bennert, T. (2013). “Grade determination of crumb rubber-modified performance graded asphalt binder.”, Center for Advanced Infrastructure and Transportation, Rutgers Univ., Piscataway, NJ.
Bennert, T., Dongre, R., Ericson, C., and Zavery, Z. (2015). “High-temperature characterization of crumb-rubber-modified asphalt binders and mixtures in New York State.” Transportation Research Board 94th Annual Meeting, Transportation Research Board, Washington, DC, 19.
California Integrated Waste Management Board. (2010). “Rubberized asphalt concrete—Application and usage.”, Technology Transfer Series, CA.
FHWA (Federal Highway Administration). (2015). “Crumb rubber modifier.” 〈http://www.fhwa.dot.gov/pavement/asphalt/crmbrubr.cfm〉 (Aug. 3, 2015).
Putman, B. J., and Amirkhanian, S. N. (2006). “Crumb rubber modification of binders: Interaction and particle effects.” Proc., Asphalt Rubber 2006 Conf., Vol. 3, Consulpav-Consultores E Projectistas De Pavimentos, LDA, Portugal, 655–677.
Putman, B. J., Thompson, U. J., and Amirkhanian, S. N. (2005). “High temperature properties of crumb rubber modified binders.” Proc. Mairepave, 4, 1–9.
Schramm, G. (1994). “A practical approach to rheology and rheometry.” Gegrueder HAAKE, Karlsruhe, Germany, 53–56.
Steffe, J. F. (1996). Rheological methods in food process engineering, Freeman Press, East Lansing, MI.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Mar 5, 2015
Accepted: Nov 17, 2015
Published online: Feb 18, 2016
Discussion open until: Jul 18, 2016
Published in print: Aug 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.