Quantification of Aggregate Morphologic Characteristics as Related to Mechanical Properties of Asphalt Concrete with Improved FTI System
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 8
Abstract
This paper introduces the improved Fourier transform interferometry (FTI) system, which captures three-dimensional (3D) high-resolution images of aggregates. The improved FTI system uses the two-dimensional (2D) fast Fourier transform (FFT2) to rapidly measure aggregate morphologic characteristics from these images, including sphericity, flatness ratio, elongation ratio, angularity, and surface texture. Eight aggregate fractions, used in two different stone matrix asphalt (SMA) mixtures, were imaged and the calculated aggregate morphologic characteristics were found to be in good agreement with manual measurement results. The influence of aggregate morphologic characteristics on the mechanical performance of asphalt concrete is further examined on mixtures from Culpeper and Staunton in terms of dynamic modulus, flow number, and fatigue performance in laboratory experiments. Experimental results show that the mechanical performance of Staunton asphalt concrete samples was better than that of those from Culpeper, as was predicted from Staunton’s better aggregate morphologic properties, such as more cubical shapes and more angular and rougher surfaces.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The study reported in this paper is a joint project of “The Influence of Aggregate Grading and Morphology on the Performance of Small-Size Stone-Matrix Asphalt Mixtures (Accession Number 01468785),” funded by Virginia Center for Transportation Innovation and Research (VCTIR). The authors sincerely appreciate the generous help and strong support received from VCTIR.
References
AASHTO. (2007). “Standard method of test for determining the fatigue life of compacted hot-mix asphalt (HMA) subjected to repeated flexural bending.” AASHTO T321, Washington, DC.
AASHTO. (2011). “Standard method of test for determining dynamic modulus of hot-mix asphalt concrete mixtures.” AASHTO T342, Washington, DC.
Akbuluta, S., Yenera, E., Arasan, S., Hinislioglua, S., and Hattatoglu, F. (2011). “Correlation between shape of aggregate and mechanical properties of asphalt concrete: Digital image processing approach.” Road Mater. Pavement Des., 12(2), 239–262.
Al-Rousan, T., Masad, E., Tutumluer, E., and Pan, T. (2007). “Evaluation of image analysis techniques for quantifying aggregate shape characteristics.” Constr. Build. Mater., 21(5), 978–990.
ASTM. (2006). “Standard test method for index of aggregate shape and texture.” ASTM D3398, West Conshohocken, PA.
ASTM. (2010). “Standard test method for flat aggregates, elongation aggregates, or flat and elongated aggregates in coarse aggregate.” ASTM D4791, West Conshohocken, PA.
ASTM. (2013). “Standard test method for determining the percentage of fractured aggregates in coarse aggregate.” ASTM D5821, West Conshohocken, PA.
Bessa, I., Branco, V., Soares, J., and Neto, J. (2014). “Aggregate shape properties and their influence on the behavior of hot-mix asphalt.” J. Mater. Civ. Eng., 04014212.
Boulton, G. S. (1978). “Boulder shapes and grain-size distributions as indicators of transport paths through a glacier and till genesis.” Sedimentology, 25(6), 773–799.
Brandon, D. G., and Kaplan, W. D. (1999). Microstructural characterization of materials, Wiley, New York.
Chen, J. S., Chang, M. K., and Lin, K. Y. (2005). “Influence of coarse aggregate shape on the strength of asphalt concrete mixtures.” J. East. Asia Soc. Transp. Stud., 6, 1062–1075.
Fernlund, J. M. R. (2005). “Image analysis method for determining 3-D shape of coarse aggregate.” Cem. Concr. Res., 35(8), 1629–1637.
Fletcher, T., Chandan, C., Masad, E., and Sivakumar, K. (2003). “Aggregate imaging system for characterizing the shape of fine and coarse aggregates.” Transportation Research Record, 1832, 67–77.
Harvey, J., and Tsai, B. (1996). “Effects of asphalt content and air void content on mix fatigue and stiffness.” Transportation Research Record, 1543, 38–45.
Hinislioglu, S., and Agar, E. (2004). “Use of waste high density polyethylene as bitumen modifier in asphalt concrete mix.” Mater. Lett., 58(3–4), 267–271.
IPC [Computer software]. 〈〉.
Kandhal, P. S., and Parker, F. (1998). “Aggregate tests related to asphalt concrete performance in pavements.”, Transportation Research Board, Washington, DC.
Krumbein, W. C. (1941). “Measurement and geological significance of shape and roundness of sedimentary aggregates.” J. Sediment. Petrol., 11, 64–72.
Lally, E. M. (2010). “Fourier transform interferometry for 3D mapping of rough and discontinuous surfaces.” Ph.D. dissertation, Virginia Polytechnic Institute and State Univ., Blacksburg, VA.
Lally, E. M., Gong, J., and Wang, A. (2010). “Method of multiple references for 3D imaging with Fourier transform interferometry.” Optic Exp., 18(17), 17591–17596.
Lees, G. (1964). “A new method for determining the angularity of aggregates.” Sedimentology, 3(1), 2–21.
Li, Y., and Wang, L. (2015). “Computer-aided procedure for determination of asphalt content in asphalt mixture using discrete element method.” Int. J. Pavement Eng., 1–10.
Little, D., Button, J., Jayawickrama, P., Solaimanian, M., and Hudson, B. (2003). “Quantify shape, angularity and surface texture of aggregates using image analysis and study their effect on performance.”, Texas Dept. of Transportation, Austin, TX.
Masad, E., Olcott, D., White, T., and Tashman, L. (2001). “Correlation of fine aggregate imaging shape indices with asphalt mixture performance.” Transportation Research Record, 1757, 148–156.
Masad, E. A. (2006). “Aggregate imaging system (AIMS): Basics and applications.” Star, 44(9), 58.
Meininger, R. C. (1998). “Aggregate test related to performance of portland cement concrete pavement.”, Transportation Research Board, Washington, DC.
Pan, T (2006). “Investigation of coarse aggregate morphology affecting hot mix behavior using image analysis.” Ph.D. dissertation, Univ. of Illinois at Urbana-Champaign, Champaign, IL.
Rao, C., and Tutumluer, E. (2000). “Determination of volume of aggregates: New image analysis approach.” Transp. Res. Rec., 1721, 73–80.
Roy, N., Veeraragavan, A., and Krishnan, J. (2015). “Interpretation of flow number test data for asphalt mixtures.” Proc. Inst. Civ. Eng., 168(3), 191–199.
Saeed, A., Hall, J. W., and Barker, W. R. (2001). “Performance-related tests of aggregates for use in unbound pavement layers.”, Transportation Research Board, Washington, DC.
Sime, L. C., and Ferguson, R. I. (2003). “Information on grain sizes in gravel-bed rivers by automated image analysis.” J. Sediment. Res., 73(4), 630–636.
Smith, M. R., and Collis, L. (1993). Aggregates: Sand, gravel and crushed rock aggregates for construction purposes, 2nd Ed., Geological Society, London.
Sun, W., Wang, L., and Tutumluer, E. (2012). “Image analysis technique for aggregate morphology analysis with two-dimensional Fourier transform method.” Transportation Research Record, 2267, 3–13.
Suo, Z., and Wong, W. G. (2009). “Nonlinear properties analysis on rutting behaviour of bituminous materials with different air void contents.” Constr. Build. Mater., 23(12), 3492–3498.
Tafesse, S., Robison Fernlund, J. M., and Sun, W., et al. (2013). “Evaluation of image analysis methods used for quantification of aggregate angularity.” Sedimentology, 60(4), 1100–1110.
Tomlinson, C. (2013). “The effect of high RAP and high asphalt binder content on the dynamic modulus and fatigue resistance of asphalt concrete.” Ph.D. dissertation, Virginia Polytechnic Institute and State Univ., Blacksburg, VA.
Unal, H., and Mimaroglu, A. (2014). “Evaluation of morphologic characteristics and mechanical performance of rockforce mineral fiber- and glass fiber-reinforced polyamide-6 composites.” Sci. Eng. Compos. Mater., 21(3), 323–328.
Wang, L., Sun, W., Lally, E. M., Wang, A., Druta, C., and Tutumluer, E. (2012). “Application of LADAR in the analysis of aggregate characteristics.”, Transportation Research Board, Washington, DC.
Wang, L., Wang, X., Mohammad, L., and Abadie, C. (2005). “Unified method to quantify aggregates shape angularity and texture using Fourier analysis.” J. Mater. Civ. Eng., 498–504.
Wang, R. Y. (2007). “Two-dimensional Fourier transform.” 〈http://fourier.eng.hmc.edu/e101/lectures/Image_Processing/node6.html〉 (Nov. 5, 2007).
Yu, H., and Shen, S. (2012). “Impact of aggregate packing on dynamic modulus of hot mix asphalt mixtures using three-dimensional discrete element method.” Construct. Build. Mater., 26(1), 302–309.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Jun 18, 2015
Accepted: Nov 13, 2015
Published online: Feb 15, 2016
Discussion open until: Jul 15, 2016
Published in print: Aug 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.