Development of a Mechanized Traveling Pluviator to Prepare Reconstituted Uniform Sand Specimens
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 2
Abstract
Preparation of uniform and repeatable reconstituted sand specimens of required density is a prerequisite for obtaining reliable results from laboratory tests. An air pluviation technique is widely used to achieve uniform and repeatable sand specimens. Many of the previously developed air pluviation setups were stationary in nature, and these setups have inherent limitations, which do not allow the preparation of large, uniform sand beds. In this study, a mechanized traveling pluviator (MTP) is developed, which has two main features, including a freely movable hopper and rigid tube made up of Plexiglas to observe the sand flow during pluviation. This study aims at understanding the effect of the number of diffuser sieves, deposition intensity (DI), and height fall (HF) on the relative density (RD) and uniformity of sand specimens. The uniformity of a sand bed is verified by conducting cone penetration tests (CPTs) using a miniature cone. Using the developed MTP setup, large uniform sand specimens with a wide range of relative densities (viz, 38%–100%) can be prepared. For the sand used in the present study, the height of the fall and the depositional intensity significantly influence the RD of sand beds, whereas diffuser sieves control the uniformity of sand beds.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support received from the Ministry of Earth Sciences, Government of India (MoES/P.O(Seismo)/1(118)/2010), to carry out the research.
References
Abbireddy, C. O. R. (2008). “Particle form and its impact on packing and shear behavior of particulate materials.” Ph.D. thesis, School of Civil and Environmental Engineering, Univ. of Southampton, Southampton, U.K.
ASTM. (2006). “Standard test methods for minimum index density and unit weight of soils and calculation of relative density.” ASTM D4254-00, West Conshohocken, PA.
ASTM. (2011). “Classification of soils for engineering purposes (unified soil classification system).” ASTM D2487-11, West Conshohocken, PA.
Bellotti, R., Ghionna, V. N., and Morabito, P. (1991). “Uniformity tests in calibration chamber samples by the thermal probe method.” Geotech. Test. J., 14(2), 195–205.
Bolton, M. D., et al. (1999). “Centrifuge cone penetration tests in sand.” Geotechnique, 49(4), 543–552.
Choi, S. K., Lee, M. J., Choo, H., Tumay, M. T., and Lee, W. (2010). “Preparation of a large-size granular specimen using a rainer system with a porous plate.” Geotech. Test. J., 33(1), 1–10.
Clayton, C. R. I., Bica, A. V. D., and Moore, S. R. (1994). “A resin impregnation technique for determination of the density variations in completed specimens of dry cohesionless soils.” Geotech., 44(1), 165–173.
Cresswell, A., Barton, M. E., and Brown, R. (1999). “Determining the maximum unit density of sands by pluviation.” Geotech. Test. J., 22(4), 324–328.
Dave, T. N., and Dasaka, S. M. (2012). “Assessment of portable traveling pluviator to prepare reconstituted sand specimens.” Geomech. Eng., 4(2), 79–90.
Dayal, U., and Allen, J. H. (1975). “The effect of penetration rate on the strength of remolded clay and sand samples.” Can. Geotech. J., 12(3), 336–348.
Dief, H. M., and Figueroa, J. L. (2003). “Shake table calibration and specimen preparation for liquefaction studies in the centrifuge.” Geotech. Test. J., 26(4), 1–8.
Fretti, C., Lo Presti, D. C. F., and Pedroni, S. (1995). “A pluvial deposition method to reconstitute well-graded sand specimens.” Geotech. Test. J., 18(2), 292–298.
Hsu, H. H., and Huang, A.-B. (1999). “Calibration of cone penetration test in sand.” Proc. Natl. Sci. Coun., 23(5), 579–590.
Kolbuszewski, J. J. (1948). “An experimental study of the maximum and minimum porosities of sands.” Proc. Sec. Int. Conf. Soil Mech. Found. Eng., 1, 158–165.
Kuerbis, R., and Vaid, Y. P. (1988). “Sand sample preparation—The slurry deposition method.” Soils Found., 8(4), 107–118.
Lagioia, R., Sanzeni, A., and Colleselli, F. (2006). “Air, water, and vacuum pluviation of sand specimens for the triaxial apparatus.” Soils Found., 46(1), 61–67.
Lo Presti, D. C. F., Berardi, R., Pedroni, S., and Crippa, V. (1993). “A new traveling sand pluviator to reconstitute specimens of well-graded silty sands.” Geotech. Test. J., 16(1), 18–26.
Lo Presti, D. C. F., Pedroni, S., and Crippa, V. (1992). “Maximum dry density of cohesionless soils by pluviation and by ASTM D 4253-83: A comparative study.” Geotech. Test. J., 15(2), 180–189.
Madabhushi, S. P. G., Houghton, N. E., and Haigh, S. K. (2006). “A new automatic sand pourer for model preparation at Univeristy of Cambridge.” Proc., 6th Int. Conf. on Physical Modelling in Geotechnics, C. W. W. W. Ng, Y. H. Wang, and L. M. Zhang, eds., Taylor & Francis, London, 217–222.
Mehdiratta, G. R., and Triandafilidis, G. E. (1978). “Minimum and maximum densities of granular materials.” Geotech. Test. J., 1(1), 34–40.
Miura, S., and Toki, S. (1982). “A sample preparation method and its effect on static and cyclic deformation strength properties of sand.” Soils Found., 22(1), 61–77.
Naidu, A. D., and Singh, D. N. (2004). “A generalized procedure for determining thermal resistivity of soils.” Int. J. Therm. Sci., 43(1), 43–51.
Rad, N. S., and Tumay, M. T. (1987). “Factors affecting sand specimen preparation by raining.” Geotech. Test. J., 10(1), 31–37.
Schneider, H. R., Chameau, J. L., and Leonards, G. A. (1989). “Chemical impregnation of cohesionless soils.” Geotech. Test. J., 12(3), 204–210.
Singh, G., Ergatoudis, J., and Siah, B. S. (1979). “A laboratory Method of measuring in-situ density distribution in dry sand.” Geotech. Test. J., 2(3), 129–135.
Stuit, H. G. (1995). “Sand in the geotechnical centrifuge.” Ph.D. thesis, Tech. Univ., Delft, Netherlands.
Sutterer, K. G., Frost, J. D., and Chameau, J. A. (1996). “Polymer impregnation to assist undisturbed sampling of cohesionless soils.” J. Geotech. Eng., 209–215.
Vaid, Y. P., and Negussey, D. (1988). “Preparation of reconstituted sand specimens.” ASTM STP 977, ASTM, West Conshohocken, PA, 405–417.
Walker, B. P., and Whitaker, T. (1967). “An apparatus for forming uniform beds of sand for model foundation tests.” Geotechnique, 17, 161–167.
Wersching, S. N., Delpak, R., and Rowlands, G. O. (1983). “A method of estimating the in-situ density of dry uniformity graded sand under controlled conditions of placement.” Geotech. Test. J., 6(2), 196–200.
Zhao, Y., et al. (2006). “Calibration and use of new automatic sand pourer.” Proc., 6th Int. Conf. on Physical Modeling in Geotechnics, C. W. W. W. Ng, Y. H. Wang, and L. M. Zhang, eds., Taylor & Francis, London, 265–270.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 28 • Issue 2 • February 2016
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jan 11, 2015
Accepted: Jun 17, 2015
Published online: Aug 4, 2015
Discussion open until: Jan 4, 2016
Published in print: Feb 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.