Use of Infrared Thermography to Detect Thermal Segregation in Asphalt Overlay and Reflective Cracking Potential
Publication: Journal of Materials in Civil Engineering
Volume 28, Issue 2
Abstract
The objectives of this study were to assess whether temperature differentials measured using infrared thermography (IRT) occur in an overlay built on top of discontinuities such as joints and cracks and to study the horizontal and vertical thermal profiles in the asphalt overlay using a validated finite element (FE) modeling approach. To achieve this objective, an infrared camera was used to monitor the temperature profiles in the asphalt mat in a number of field projects from the time it was placed to after completion of the compaction process. The temperature profiles were monitored on top and away from severe discontinuities and joints in the existing pavement. Based on IRT measurements, cracks in the existing pavement did not influence the thermal profiles in a hot-mix asphalt overlay. However, thermal measurements on top of a joint were consistently lower than away from it as observed in thermal images, which may indicate that temperature loss may occur at the joints. Based on FE simulations, the model predicted a slightly higher rate of thermal decrease at the bottom of the overlay above the joint than away from it attributable to convection losses at the joint. While this difference may not be large enough to be identified as thermal segregation, it can influence the bulk properties of the overlay at the joints and promote early cracking. Results also show that thermal differences occur in the vertical direction as well as in the horizontal direction in the asphalt mat.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was funded through a grant from the Gulf Coast Research Center for Evacuation and Transportation Resiliency. The assistance of Mehdi Moayedi, Wayne Marchand, and Phillip Miller is greatly appreciated.
References
ABAQUS version 6.13 [Computer software]. Pawtucket, RI, Dassault Systèmes Simulia Corp.
Al-Qadi, I. L., Hassan, M. M., and Elseifi, M. A. (2005). “Field and theoretical evaluation of thermal fatigue cracking in flexible pavements.”, Transportation Research Board, Washington, DC, 87–95.
Amirkhanian, S., and Hartman, E. (2004). “Applications of infrared cameras in the paving industry.” Proc., InfraMation 2004, Vol. 5, 91–99.
Brock, D. J., and Jakob, H. (1997). “Temperature segregation/temperature differential damage.” Astec Industries, Chattanooga, TN.
Brown, E. R. (1990). “Density of asphalt concrete: How much is needed?”, Transportation Research Board, Washington, DC, 27–32.
Henault, J. W., Larsen, D. A., and Scully, J. J. (2005). “Development of guidelines for reduction of temperature differential damage (TDD) for hot mix asphalt pavement projects in Connecticut.”, Connecticut Dept. of Transportation, Bureau of Engineering and Highway Operations, Division of Research, Rocky Hill, CT.
Huber, G. A., and Hernam, G. H. (1987). “Effect of asphalt concrete parameters on rutting performance– a field investigation.” Proc., AAPT, Vol. 56, Viking Press Inc., Eden Prairie, MN, 33–61.
Li, H., and Harvey, J. (2010). “Numerical simulation and sensitivity analysis of asphalt pavement temperature and near-surface air temperature using integrated local modeling.” 90th Annual Meeting of the Transportation Research Board, Transportation Research Board, Washington, DC, 11–3125.
Mahoney, J., Zinke, S. A., Stephens, J. E., Myers, L. A., and DaDalt, J. A. (2003). “Application of infrared thermographic imaging to bituminous concrete pavements.”, Connecticut Transportation Institute Storrs, CT, 3–7.
Minhoto, M. J., Pais, J. C., Pereira, P. A., and Picado-Santos, L. G. (2005). “Predicting asphalt pavement temperature with a three-dimensional finite element method.”, Transportation Research Board, Washington, DC, 96–110.
Phillips, L. (2008). “Infrared thermography revolutionizes asphalt paving-significant cost saving for states and municipalities.” 〈http://www.lenphillips.com/images/FEATURES/Asphalt_6_17_03_low2.pdf〉 (Jun. 2015).
Rahman, M. M., Grenfell, J. R., Arulanandam, S. J., and Ianakiev, A. (2013). “Influence of thermal segregation on asphalt pavement compaction.”, Transportation Research Board, Washington, DC, 71–78.
Santucci, L. E., Allen, D. D., and Coats, R. L. (1985). “The effect of moisture and compaction on the quality of asphalt pavements.” Proc., AAPT, Vol. 54, Viking Press Inc., Eden Prairie, MN, 168–208.
Sebesta, S., and Scullion, T. (2012a). “Performance monitoring pavements with thermal segregation in Texas.”, Texas Transportation Institute, College Station, TX.
Sebesta, S., and Scullion, T. (2012b). “Statewide implementation of PAVE-IR in the Texas department of transportation.”, Texas Transportation Institute, College Station, TX.
Song, J., Abdelrahman, M., and Asa, E. (2009). “Use of a thermal camera during asphalt pavement construction.” North Dakota Dept. of Transportation, Bismarck, ND.
Stroup-Gardiner, M., and Brown, E. R. (2000). “Segregation in hot-mix asphalt pavements.”, Transportation Research Board, Washington, DC.
Willoughby, K. A., et al. (2001). “Construction-related asphalt concrete pavement temperature differentials and the corresponding density differentials.”, Washington State Dept. of Transportation, Olympia, Washington.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Dec 10, 2014
Accepted: Jun 29, 2015
Published online: Aug 5, 2015
Discussion open until: Jan 5, 2016
Published in print: Feb 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.