Laboratory Evaluation of Warm-Mix Open Graded Friction Course Mixtures
Publication: Journal of Materials in Civil Engineering
Volume 25, Issue 3
Abstract
The objective of this study was to evaluate the feasibility of using warm mix asphalt (WMA) technologies to produce quality open graded friction course (OGFC) mixtures. This evaluation was based on the comparison of Evotherm WMA and foamed WMA mixes with traditional hot mix asphalt (HMA) OGFC using three primary criteria: draindown, permeability, and abrasion resistance. The results of the study indicated that fibers could be removed from OGFC mixtures when using the WMA technologies included in this study. This conclusion was based on the performance evaluation of the mixtures, which showed that when the fibers were removed, the permeability of the mix almost doubled. Additionally, the WMA mixtures without fibers met typical aged abrasion loss requirements and the foamed WMA mixtures without fibers performed similarly with regard to aged abrasion resistance to the HMA mixture with fibers, whereas the HMA mix without fibers showed lower resistance to abrasion than the WMA mixtures. The enhanced performance of the mixtures can be attributed to the increased binder film thickness of the WMA mixtures compared to the HMA mixtures without fibers.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors wish to acknowledge MeadWestvaco Corp. and the South Carolina Department of Transportation for their financial and technical support of this project.
References
AASHTO. (2005). “Standard method of test for determination of draindown characteristics in uncompacted asphalt mixtures.” T305, Washington, DC.
Alvarez, A. E., Epps Martin, A., Estakhri, C. K., Button, J. W., Glover, C. J., and Jung, S. H. (2006). “Synthesis of current practice on the design, construction, and maintenance of porous friction courses.”, Texas Transportation Institute, Texas A&M Univ., College Station, TX.
Alvarez, A. E., Epps Martin, A., Estakhri, C., and Izzo, R. (2010). “Evaluation of durability tests for permeable friction course mixtures.” Int. J. Pavement Eng., 11(1), 49–60.
ASTM. (2003). “Standard test method for theoretical maximum specific gravity and density of bituminous paving mixtures.” D2041, West Conshohocken, PA.
ASTM. (2005). “Standard test method for effective porosity and effective air voids of compacted bituminous paving mixture samples.” D7063, West Conshohocken, PA.
ASTM. (2008). “Standard practice for open-graded friction course (OGFC) mix design.” D7064, West Conshohocken, PA.
Barros, C. B., and Dmytrow, S. (2009). “Weather-mix asphalt.” Roads and Bridges, 47(4), 26–28.
Bennert, T. (2011). “Laboratory characterization of a stone matrix asphalt (SMA) using warm mix technology (Evotherm 3G).”, Center for Advanced Infrastructure and Transportation (CAIT), Piscataway, NJ.
Cooley, L., Jr., et al. (2009). “Construction and maintenance practices for permeable friction courses.”, Transportation Research Board, National Research Council, Washington, DC.
Copeland, A., Jones, C., and Bukowski, J. (2010). “Reclaiming roads.” Public Roads, 73(5).
Decoene, Y. (1990). “Contribution of cellulose fibers to the performance of porous asphalts.” Transportation Research Record 1265, Transportation Research Board, Washington, DC.
Huber, G. (2000). “Performance survey on open-graded friction course mixes.”, Transportation Research Board, National Research Council, Washington, DC.
Hurley, G. C., and Prowell, B. D. (2006). “Evaluation of potential processes for use in warm mix asphalt.” J. Assoc. Asphalt Paving Technol., 75, 41–85.
Jones, D., Tsai, B. W., and Signore, J. (2010). “Warm-mix asphalt study: Laboratory test results for AkzoNobel Rediset WMX.”, Univ. of California Pavement Research Center, Richmond, CA.
Kandhal, P. (2002). Design, construction, and maintenance of open-graded asphalt friction courses, Information Series 115, National Asphalt Pavement Association, Lanham, MD.
Kline, L. C., and Putman, B. J. (2011). “Comparison of open graded friction course (OGFC) mix design procedures in the United States.” 90th Annual Meeting of the Transportation Research Board (CD-ROM), Transportation Research Board of the National Academies, Washington, DC.
Mo, L. T., Huurman, M., Woldekidan, M. F., Wu, S. P., and Molenaar, A. (2010). “Investigation into material optimization and development for improved ravelling resistant porous asphalt concrete.” Mater. Des., 31(7), 3194–3206.
Prowell, B. D., and Hurley, G. C. (2007). Warm-mix asphalt: Best practices, Quality Improvement Publication 125, National Asphalt Pavement Association, Lanham, MD.
Putman, B. J., and Amirkhanian, S. N. (2004). “Utilization of waste fibers in stone matrix asphalt mixtures.” J. Resour. Conserv. and Recycl., 42(3), 265–274.
South Carolina Dept. of Transportation (SCDOT). (2007). Standard specifications for highway construction—Section409, Columbia, SC.
South Carolina Dept. of Transportation (SCDOT). (2010a). “Method of determining the effectiveness of anti-stripping additives in hot asphalt mixtures.” SC-T-69, Office of Materials and Research, Columbia, SC.
South Carolina Dept. of Transportation (SCDOT). (2010b). “Method of determining the optimum binder content in an uncompacted bituminous mixture.” SC-T-91, Office of Materials and Research, Columbia, SC.
Vaitkus, A., Cygas, D., Laurinavicius, A., and Perveneckas, Z. (2009). “Analysis and evaluation of possibilities for the use of warm mix asphalt in Lithuania.” Baltic J. Road Bridge Eng., 4(2), 80–86.
Wielinski, J., Hand, A., and Rausch, D. M. (2009). “Laboratory and field evaluations of foamed warm-mix asphalt projects.” Transportation Research Record 2126, Transportation Research Board, Washington, DC.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 11, 2012
Accepted: Jun 7, 2012
Published online: Aug 28, 2012
Published in print: Mar 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.