Using Isothermal Calorimetry to Assess the Water Absorbed by Fine LWA during Mixing
Publication: Journal of Materials in Civil Engineering
Volume 24, Issue 8
Abstract
Fine lightweight aggregate (LWA) is being increasingly used for the manufacture of internally cured concrete. Internally cured concrete can be viewed as a concrete that contains fluid (water) in the pores of the LWA (or other porous inclusions) that can be released to the paste after setting. Most research performed on internally cured concrete assumes the LWA has been prewetted for some time before mixing (generally lab studies use 24-h soaking, whereas this value varies in practice). The research described in this paper investigated the potential for using aggregate that begins the mixing process from a different moisture state (i.e., not 24-h prewetting). Specifically, this paper considers oven-dry aggregate as a worst-case scenario to determine how much water would be absorbed by the LWA during the mixing and placement processes. To determine the amount of water absorbed by the LWA, isothermal calorimetry was used. Two different mixing scenarios were investigated, showing that 56–71% of the 24-h water absorption could be achieved using the worst-case scenario of oven-dry aggregates. Although the use of oven-dry aggregate would be extremely rare for a field application (except for possible application to bagged products), this approach could be extended to include fine LWA with other initial moisture conditions.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported in part by the Expanded Shale, Clay and Slate Institute (ESCSI) and by the Joint Transportation Research Program administered by the Indiana Department of Transportation and Purdue University (Project SPR 3211), and the authors gratefully acknowledge that support. The contents of this paper reflect the views of the authors, who are responsible for the facts and the accuracy of the data presented and do not necessarily reflect the official views or policies of the Indiana Department of Transportation or ESCSI, nor do the contents constitute a standard, specification, or regulation. The experiments reported in this paper were conducted in the Pankow Materials Laboratories at Purdue University. The authors acknowledge the support that has made this laboratory and its operation possible.
References
ASTM. (2006). “Standard practice for mechanical mixing of hydraulic cement pastes and mortars of plastic consistency.” ASTM C305, West Conshohocken, PA.
ASTM. (2011). “Standard specification for Portland cement.” ASTM C150, West Conshohocken, PA.
Bensted, J., and Barnes, P. (2002). Structure and performance of cements, 2nd Ed., Spon Press, Taylor and Francis Group, New York.
Bentz, D. P. (2010). “Critical observations for the evaluation of cement hydration models.” Int. J. Adv. Eng. Sci. Appl. Math., 2(3), 75–82.
Bentz, D. P., Lura, P., and Roberts, J. W. (2005). “Mixture proportioning for internal curing.” Concr. Int., 27(2), 35–40.CNCIEH
Bentz, D. P., Peltz, M. A., and Winpigler, J. (2009). “Early-age properties of cement-based materials II: Influence of water-to-cement ratio.” J. Mater. Civ. Eng., 21(9), 512–517.JMCEE7
Bentz, D. P., and Snyder, K. A. (1999). “Protected paste volume in concrete: Extension to internal curing using saturated lightweight fine aggregate.” Cem. Concr. Res., 29(11), 1863–1867.CCNRAI
Bloem, D. L. (1965). “Concrete strength measurements: Cores and cylinders.” ASTM Proceedings, Vol. 65, ASTM, West Conshohocken, PA.
Castro, J., Keiser, L., Golias, M., and Weiss, J. (2011). “Absorption and desorption properties of fine lightweight aggregate for application to internally cured concrete mixtures.” Cem. Concr. Compos., 33(10), 1001–1008.CCOCEG
Castro, J., Lura, P., Rajabipour, F., Henkensiefken, R., and Weiss, J. (2010). “Internal curing: Discussion of the role of pore solution on relative humidity measurements and desorption of lightweight aggregate.” Special Publication 270-8, American Concrete Institute, Farmington Hills, MI, 89–100.
Castro, J., Spragg, R., and Weiss, J. (2012). “Water absorption and electrical conductivity for internally cured mortars with a between 0.30 and 0.45.” J. Mater. Civ. Eng., 24(2), 223–231 JMCEE7.
Elsharief, S., Menashi, D., and Olek, J. (2005). “Influence of lightweight aggregate on the microstructure and durability of mortar.” Cem. Concr. Res., 35(7), 1368–1376.CCNRAI
Geiker, M. (1983). “Studies of portland cement hydration by measuring of chemical shrinkage and a systematic evaluation of hydration curves by means of the dispersion model.” Ph.D. dissertation, Technical Univ. of Denmark, Lyngby, Denmark.
Golias, M., Castro, J., and Weiss, J. (2012). “Moisture content in lightweight aggregate and its influence on internal curing in concrete.” Constr. Build. Mater., 35, 52–62.
Henkensiefken, R., Castro, J., Bentz, D., Nantung, T., and Weiss, J. (2009). “Water absorption in internally cured mortar made with water-filled lightweight aggregate.” Cem. Concr. Res.CCNRAI, 39(10), 883–892.
Holm, T. A., Ooi, O. S., and Bremner, T. W. (2004). “Moisture dynamics in lightweight aggregate and concrete.” Publication 9340, Expanded Shale Clay and Slate Institute, Salt Lake City.
Jensen, O. M., and Hansen, P. F. (2001). “Water-entrained cement-based materials. I: Principles and theoretical background.” Cem. Concr. Res.CCNRAI, 31(4), 647–654.
Johansen, N. A., Millard, M. J., Mezencevova, A., Garas, V. Y., and Kurtis, K. E. (2009). “New method for determination of absorption capacity of internal curing agents.” Cem. Concr. Res.CCNRAI, 39(1), 65–68.
Kantro, D. L. (1980). “Influence of water-reducing admixtures on properties of cement paste-a miniature slump test.” Cem., Concr., AggregatesCCAGDP, 2(2), 95–102.
Klieger, P. (1957). “Early high strength concrete for prestressing.” Bulletin RX091, Portland Cement Association, Research and Development Laboratories Research Dept., Skokie, IL.
Landgren, R. (1964). “Water-vapor adsorption-desorption characteristics of selected lightweight concrete aggregates.” Bulletin 178, Portland Cement Association, Research and Development Laboratories, Skokie, IL.
Lopez, M., Kahn, L. F., and Kurtis, K. E. (2009). “Characterization of elastic and time-dependent deformations in high performance lightweight concrete by image analysis.” Cem. Concr. Res.CCNRAI, 39(7), 610–619.
Lura, P., Winnefeld, F., and Klemm, S. (2010). “Simultaneous measurements of heat of hydration and chemical shrinkage on hardening cement pastes.” J. Therm. Anal. Calorim.JTACF7, 101(3), 925–932.
Mills, R. H. (1966). “Factors influencing cessation of hydration in water-cured cement pastes.” Special Rep. No. 90, Highway Research Board, Washington, DC, 406–424.
New York Dept. of Transportation (NYDOT). (2008). “Test method to determine the moisture content of lightweight fine aggregate.” Test Method No. NY 703-19E, NYDOT, Materials Bureau, Albany, NY.
Pane, I., and Hansen, W. (2005). “Investigation of blended cement hydration by isothermal calorimetry and thermal analysis.” Cem. Concr. Res.CCNRAI, 35(6), 1155–1164.
Peled, A., Castro, J., and Weiss, J. (2010). “Atomic force microscopy examinations of mortar made by using water-filled lightweight aggregates.” Transportation Research Record 2141, Transportation Research Board, Washington, DC, 92–101.
Philleo, R. (1991). Concrete science and reality, Skalny, J. P. and Mindess, S., eds., Materials Science of Concrete II American Ceramic Society, Westerville OH.
Poole, J. L., Riding, K. A., Juenger, M. C. G., Schindler, A. K., and Folliard, K. J. (2007). “Methods for calculating activation energy for portland cement.” ACI Mater. J.AMAJEF, 104(1), 303–311.
Pour-Ghaz, M., Castro, J., Kladivko, E. J., and Weiss, J. (2011). “Characterizing lightweight aggregate desorption at high relative humidities using a pressure plate apparatus.” J. Mater. Civ. Eng., JMCEE7 〈〉 (Nov. 11, 2011).
RILEM. (2003). Early age cracking in cementitious systems: Report of RILEM Technical Committee 181-EAS. Early age shrinkage induced stresses and cracking in cementitious systems, Bentur, A., ed., Bagneux, France.
RILEM. (2007). Internal curing of concrete: State-of-the-art report of RILEM Technical Committee 196-ICC, Kovler, K. and Jensen, O. M., eds., Bagneux, France.
Schindler, A. K., and Folliard, K. J. (2005). “Heat of hydration models for cementitious materials.” ACI Mater. J.AMAJEF, 102(1), 24–33
TA Instruments. (2008). TAM air calorimeter operator’s manual: Revision C, TA Instruments, New Castle, DE.
Taplin, J. H. (1959). “A method for following the hydration reaction in portland cement paste.” Aust. J. Appl. Sci.AJACA3, 10(3), 329–345.
Trtik, P., et al. (2011). “Release of internal curing water from lightweight aggregates in cement paste investigated by neutron and x-ray tomography.” Nucl. Instrum. Methods Phys. Res., Sect. ANIMAER, 651(1), 244–249.
Weiss, J. (1997). “Shrinkage cracking in restrained concrete slabs: Test methods, material compositions, shrinkage reducing admixtures and theoretical modeling.” M.Sc. thesis, Northwestern Univ., Evanston, IL.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 24 • Issue 8 • August 2012
Pages: 996 - 1005
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Jun 3, 2011
Accepted: Feb 1, 2012
Published online: Feb 3, 2012
Published in print: Aug 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.