Performance and Cost-Effectiveness of Sustainable Technologies in Flexible Pavements Using the Mechanistic-Empirical Pavement Design Guide
Publication: Journal of Materials in Civil Engineering
Volume 24, Issue 2
Abstract
Past studies evaluated the mechanistic properties, economic benefits, and ecological impacts of sustainable asphalt mixtures. However, questions remain concerning the effects of these technologies on structural pavement design and performance. The objectives of this study were to evaluate the effects of selected sustainable technologies [warm-mix asphalt (WMA), reclaimed asphalt pavement (RAP), crumb rubber modifier (CRM), and sulfur additive] on the performance predicted by the Mechanistic-Empirical Pavement Design Guide (MEPDG) software and to assess the life-cycle costs (LCC) of pavement structures constructed with these sustainable alternatives. This study also determined if the MEPDG software is sensitive to variation in the mechanistic properties of asphalt mixtures containing selected sustainable technologies. Three typical pavement structures were analyzed at three traffic levels (low, medium, and high). On the basis of the results of this analysis, it was determined that the performance predicted by the MEPDG software was improved because of the use of sustainable mixtures. In addition, results indicated that sustainable technologies have the potential to reduce production and LCCs compared with conventional asphalt mixtures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to acknowledge the support of Shell, Inc. and the Louisiana Transportation Research Center (LTRC). The assistance of Yoonseok Chung and Bhanu Vijay Vallabhu is also greatly appreciated.
References
Bloomberg, T. (1999). “Partial life cycle inventory or ‘Eco-profile’ for paving grade bitumen.” Eurobitume Rep. 99/007.
Buss, A., Rashwan, M., Breakah, T., Williams, R. C., and Kvasnak, A. (2009). “Investigation of warm-mix asphalt using the mechanistic-empirical pavement design guide.” 2009 Mid-Continent Transportation Research Symp., Iowa State University, Ames, IA.
Canadian Industry Program for Energy Conservation (CIPEC). (2005). “Road rehabilitation energy reduction guide for Canadian road builders.” Rep. No. TE26.R62 2005, Ottawa, Ontario, Canada.
Cooper, S. B., Jr. (2008). “Characterization of HMA mixtures containing high recycled asphalt pavement content with crumb rubber additives.” MSCE thesis, Louisiana State University.
Cooper, S. B., Mohammad, L. N., and Elseifi, M. A. (2011). “Laboratory performance characteristics of sulfur-modified warm-mix asphalt.” J. Mater. Civ. Eng., 23(9), 1338–1345.
Daniel, J. S., Chehab, G. R., and Ayyala, D. (2009). “Sensitivity of RAP binder grade on performance predictions in the MEPDG.” Annual Meeting and Technical Sessions CD, Association of Asphalt Paving Technologists (AAPT), Minneapolis, MN.
Diefenderfer, S., and Hearon, A. (2008). “Laboratory evaluation of a warm asphalt technology for use in Virginia.” VTRC 09-R11 Final Rep., Virginia Transportation Research Council, Charlottesville, VA.
Goh, S. W., Zhanping, Y., and Van Dam, T. J. (2007). “Laboratory evaluation and pavement design for warm mix asphalt.” 2007 Mid-Continent Transportation Research Symp., Iowa State University, Ames, IA.
Hassan, M. M. (2010). “Evaluation of the environmental and economic impacts of warm-mix asphalt using life-cycle assessment.” Int. J. Constr. Education Res., 6(3), 238–250.
Huang, Y. H. (2004). Pavement analysis and design, 2nd Ed., Pearson Prentice Hall.
Ishak, S., Shin, H., and Sridhar, B. (2009). “Characterization and development of truck load spectra and growth factors for current and future pavement design practices in Louisiana.” LTRC Rep. 07-2P, Louisiana Transportation Research Center, Baton Rouge, LA.
Kristjansdottir, O., Muench, S. T., Michael, L., and Burke, G. (2007). “Assessing the potential for warm mix asphalt technology adoption.” Transportation Research Record: J. Transp. Res. Board, No. 2040, Transportation Research Board of the National Academies, Washington, DC, 91–99.
Maupin, G. W., Diefenderfer, S. D., and Gillespie, J. S. (2009). “Performance and economic evaluation of Virginia’s higher RAP specification.” Transportation Research Record: J. Transp. Res. Board, No. 2126, Transportation Research Board of the National Academies, Washington, DC, 142–150.
Mohammad, L. M., Herath, A., Gudishala, R., Nazzal, M. D., Abu-Farsakh, M. Y., and Alshibli, K. (2008). “Development of models to estimate the subgrade and subbase layers’ resilient modulus from in situ devices test results for construction control.” LTRC Rep. 02-4B, Louisiana Transportation Research Center, Baton Rouge, LA.
Muench, S. T. (2010). “Roadway construction sustainability impacts: A review of life cycle assessments.” Transportation Research Board 89th Annual Meeting, Transportation Research Board of the National Academies, Washington, DC.
National Cooperative Highway Research Program (NCHRP). (2004). “Guide for mechanistic-empirical design of new and rehabilitated pavement structures. Final Rep. Part 2. Design inputs. Chapter 4. Traffic.” NCHRP 1-37A.
National Cooperative Highway Research Program (NCHRP). (2010). “1-37A Climatic data.” 〈http://www.trb.org/mepdg/climatic_state.htm〉 (Jan. 2010).
Roque, R., Birgisson, B., Drakos, C., and Dietrich, B. (2004). “Development and field evaluation of energy-based criteria for top-down cracking performance of hot-mix asphalt.” J. Assoc. Asphalt Paving Technol., Vol. 73, Baton Rouge, LA.
Timm, D., Tran, N., Taylor, A., Robbins, M., and Powell, B. (2009). “Evaluation of mixture performance and structural capacity of pavements utilizing Shell Thiopave® Phase I: Mix design, laboratory performance evaluation and structural pavement analysis and design.” NCAT Rep. 09-05, National Center for Asphalt Technology, Auburn, AL.
U.S. Energy Information Administration (EIA). (2010). 〈http://www.eia.doe.gov〉 (Jun. 2010).
Uzarowski, L. (2008). “Sustainable pavements—Making the case for longer design lives for flexible pavements.” 2008 Annual Conf. of the Transportation Association of Canada, Ottawa, Ontario, Canada.
Williams, T. A., and Williamson, A. K. (1989). “Estimating water-table altitudes for regional ground-water flow modeling, U.S. Gulf Coast.” Gulf Coast: Ground water, 27(3), 333–340.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Mar 25, 2011
Accepted: Aug 5, 2011
Published online: Jan 17, 2012
Published in print: Feb 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.