Coupled Thermochemical Effects on the Strength Development of Slag-Paste Backfill Materials
Publication: Journal of Materials in Civil Engineering
Volume 23, Issue 5
Abstract
In this paper, the coupled effects of sulfate (chemical factor) and curing temperature (thermal factor) on the strength development of cemented paste backfill (slag-CPB) that contains ground granulated blast furnace slag (slag) as a mineral admixture is studied. Almost 200 slag-CPB samples, cured at temperatures of 2, 20, 35, and 50°C at 28, 90, and 150 days with sulfate concentrations of zero ppm, 5,000 ppm, 15,000 ppm, and 25,000 ppm are tested for uniaxial compressive strength (UCS). The results show that the effect of sulfate on the strength of slag-CPB is significantly dependent on the curing temperature, initial sulfate content, and curing time. The coupled effects of sulfate and temperature can lead to an increase or decrease of the slag-CPB strength and significantly influence the type and amount of minerals formed within the cemented matrix of slag-CPBs. The strength-increasing factors are (1) refinement of the pore structure of slag-CPBs due to the precipitation of ettringite within the empty pores of the cemented matrix; (2) faster cement hydration rate and pozzolanic reaction with higher curing temperatures; and (3) activation of the slag reaction by sulfate ions. The identified strength-decreasing factors include (1) sulfate absorption by calcium silicate hydrate (C-S-H) that could lead to the formation of weaker C-S-H gel; (2) increase of ettringite dissolution as the curing temperature increases that results in the coarsening of the pore structure; (3) inhibition of cement hydration by sulfate; and (4) formation of hydration rims around the slag grains at high temperatures. There is competition between the strength-decreasing and increasing factors. The dominant influencing factors depend on the curing temperature, curing time, and initial sulfate content. A comparison of the performance of slag-CPBs and portland cement CPBs shows that a partial replacement of ordinary portland cement with slag improves the resistance of the studied cemented paste backfill at advanced ages and curing temperatures of 2°C and 20°C, while negatively affecting resistance for curing temperatures that are . This study has demonstrated that the coupled effects of sulfate and temperature on the strength of cemented paste backfill are an important factor that should be considered in the designing of cost-effective, safe, and durable cemented paste backfill structures.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to acknowledge the National Sciences and Engineering Research Council of Canada (NSERC), the University of Ottawa, the National Research Council (NRC) of Canada, and Cement Lafarge, Inc. The writers also would like to thank Dr. J. Beaudoin from NRC for his valuable review of this work.
References
Aköz, F., Türker, F., Koral, S., and Yüzer, N. (1995). “Effects of sodium sulfate concentration on the sulfate resistance of mortars with and without silica fume.” Cem. Concr. Res., 25(6), 1360–1368.
Alarcon-Ruiz, L., Platret, G., Massieu, E., and Ehrlacher, A. (2005). “The use of thermal analysis in assessing the effect of temperature on a cement paste.” Cem. Concr. Res., 35(3), 609–613.
Aziz, M. A., Aleem, S. A., Heikal, M., and Didamony, H. El. (2005). “Hydration and durability of sulphate-resisting and slag cement blends in Caron’s Lake water.” Cem. Concr. Res., 35(8), 1592–1600.
Barbarulo, R. (2002). “Comportement des matériaux cimentaires: Actions des sulfates et de la température.” Ph.D. thesis, École Normale Supérieure de Cachan, France–Université Laval, Canada, (in French).
Barbarulo, R., Peycelon, H., and Leclercq, S. (2007). “Chemical equilibria between C-S-H and ettringite, at 20 and 85°C.” Cem. Concr. Res., 37(8), 1176–1181.
Barker, A. P. (1989). “An electron optical examination of zoning in blast furnace slag hydrates. Part 1: Slag cement pastes at early ages.” Adv. Cem. Res., 2, 171–179.
Barnett, S. J., Soutsos, M. N., Millard, S. G., and Bungey, J. H. (2006). “Strength development of mortars containing ground granulated blast-furnace slag effect of curing temperature and determination of apparent activation energies.” Cem. Concr. Res., 36(3), 434–440.
Battagin, A. F. (1992). “Influence of degree of hydration of slag on slag cements.” Proc., 9th Int. Congress on the Chemistry of Cement, India, Vol. 3, 166–172.
Bentur, A. (1976). “Effect of gypsum on the hydration and strength of Pastes.” J. Am. Ceram. Soc., 59, 210–213.
Birchall, J. D., Howard, A. J., and Bailey, J. E. (1978). “On the hydration of portland cement.” Proc., Royal Society of London. Series A, Mathematical and Physical Sciences, 360, 445–453.
Divet, L., and Randriambololona, R. (1998). “Delayed ettringite formation: The effect of temperature and basicity on the interaction of sulphate and C-S-H phase.” Cem. Concr. Res., 28(3), 357–363.
Double, D. D. (1983). “New developments in understanding the chemistry of cement hydration.” Philos. Trans. R. Soc. A, 310(1511), 53–56.
Escalante-Garcia, J. I., and Sharp, J. H. (2001). “The microstructure and mechanical properties of blended cements hydrated at various temperatures.” Cem. Concr. Res., 31, 695–702.
Fall, M., Adrien, D., Célestin, J. C., Pokharel, M., and Touré, M. (2009a). “Saturated hydraulic conductivity of cemented paste backfill.” Miner. Eng., 22(15), 1307–1317.
Fall, M., and Benzaazoua, M. (2005). “Modeling the effect of sulphate on strength development of paste backfill and binder mixture optimization.” Cem. Concr. Res., 35, 301–314.
Fall, M., Benzaazoua, M., and Ouellet, S. (2005). “Experimental characterization of the effect of tailings fineness and density on the quality of cemented paste backfill.” Miner. Eng., 18(1), 41–44.
Fall, M., Benzaazoua, M., and Saa, E. (2008). “Mix proportioning of underground cemented paste backfill.” Tunnelling Underground Space Technol., 23(1), 80–90.
Fall, M., Célestin, J. C., and Han, F. S. (2009b). “Suitability of bentonite-paste tailings mixtures as engineering barrier material for mine waste containment facilities.” Miner. Eng., 22(9–10), 840–848.
Fall, M., Célestin, J. C., Pokharel, M., and Touré, M. (2010). “A contribution to understanding the effect of temperature on the mechanical properties of mine cemented tailings backfill: Experimental results.” Eng. Geol., 114(3–4), 397–413.
Fall, M., Nasir, O., and Celestin, J. C. (2007). Paste backfill response in deep mine temperature conditions, (CD-ROM), Symposium MineFill, Montreal.
Fall, M., and Pokharel, M. (2009). “Coupled effect of sulphate and temperature on the strength of cemented tailings backfills: Portland cement-paste backfill.” Cem. Concr. Compos., 32(10), 819–828.
Fall, M., and Samb, S. S. (2008). “Pore structure of cemented tailings materials under natural or accidental thermal loads.” Mater. Charact., 59(5), 598–605.
Fu, Y., Xie, P., and Beaudoin, J.-J. (1994). “Effect of the temperature on sulfate adsorption/desorption by tricalcium silicate hydrates.” Cem. Concr. Res., 24(8), 1428–1432.
Gani, M. S. J. (1997). Cement and concrete, 1st ed., Chapman and Hall, London.
Grice, T. (2001). “Recent mine developments in Australia.” Proc., 7th Int. Symp. on Mining with Backfill (MINEFILL), 351–357.
Gruskovnjak, A., et al. (2008). “Hydration mechanisms of super sulphated slag cement.” Cem. Concr. Res., 38(7), 983–992.
Häcker, C. J., and Bentz, D. P. (2000). “Influence of sulphate source and content on hydration kinetics and compressible strength of portland cement.” Dr. CH-2000-06-13-NIST/industry consortium, Wilhelm Dyckerhoff Institut, Wiesbaden-Biebrich, Germany.
Hassani, F., and Archibald, J. (1998). Mine backfill, (CD-ROM), Canadian Institute of Mine, Metallurgy and Petroleum, 262.
Hekal, E. E., Kishar, E., and Mostafa, H. (2002). “Magnesium sulfate attack on hardened blended cement pastes under different circumstances.” Cem. Concr. Res., 32(9), 1421–1427.
Jelenić, I., Panović, A., Halle, R., and Gaćeša, T. (1977). “Effect of gypsum on the hydration and strength development of commercial portland cements containing alkali sulfates.” Cem. Concr. Res., 7(3), 239–245.
Kesimal, A., Ercikdi, B., and Yilmaz, E. (2003). “The effect of desliming by sedimentation on paste backfill performance.” Miner. Eng., 16(10), 1009–1011.
Kesimal, A., Yilmaz, E., Ercikdi, B., and Deveci, H. (2005). “Effect of properties of tailings and binder on the short-and long-term strength and stability of cemented paste backfill.” Mater. Lett., 59(28), 3703–3709.
Kühl, H., and Schleicher, E. (1952). Gipsschlackenzement, Fachbuchverlag GmbH, Leipzig, Germany. 34.
Landriault, D. (1995). “Paste backfill mix design for Canadian underground hard rock mining.” 97th Annual General Meeting of CIM. Rock Mechanics and Strata Control Session, Halifax, Nova Scotia, 229–238.
Levens, R. L., Marcy, A. D., and Boldt, C. M. K. (1996). Environmental impacts of cemented mine waste backfill. RI 9599, U. S. Bureau of Mines, Washington, DC, 23.
Lothenbach, B., Winnefeld, F., Alder, C., Wieland, E., and Lunk, P. (2007). “Effect of temperature on the pore solution, microstructure and hydration products of portland cement pastes.” Cem. Concr. Res., 37(4), 483–491.
Manmohan, D., and Mehta, P. K. (1981). “Influence of pozzolanic slag, and chemical admixtures on pore size distribution and permeability of hardened cement pastes.” Cem., Concr., Aggregates, 3(1), 63–67.
Mehta, P. K. (1976). “Scanning electron micrographic studies of ettringite formation cement and concrete.” Cem. Concr. Res., 6, 169–182.
Nasir, O., and Fall, M. (2008). “Shear behavior of cemented pastefill-rock interfaces.” Eng. Geol., 101(3-4), 146–153.
Noumowé, A. (1995). “Effet des hautes températures (20°C–600°C) sur le béton.” Ph.D. thesis, Institut National des Sciences Appliquées.
Odler, I. (1981). “Interaction between gypsum and the C-S-H phase formed in hydration.” Proc. 7th Int. Congr. Chem. Cem., Paris 1980, Vol. 4, Paris, 493–495.
Perkins, R. B., and Palmer, C. D. (1998). “Solubility of ettringite at 5–75°C.” Geochim. Cosmochim. Acta, 63(13/14), 1969–1980.
Ping, X., and Beaudoin, J. J. (1992a). “Mechanism of sulphate expansion. I: Thermodynamic Principle of Crystallization Pressure.” Cem. Concr. Res., 22(4), 631–640.
Ping, X., and Beaudoin, J. J. (1992b). “Mechanism of sulphate expansion. II: Validation of Thermodynamic Theory.” Cem. Concr. Res., 22(5), 845–854.
Pokharel, M. (2008). “Geotechnical and environmental response of paste tailings systems to coupled thermo-chemical loadings.” M.A.Sci. thesis, Univ. of Ottawa, 248.
Smolczyk, H. G. (1965). “Die hydratations-produkte hüttensandreicher zemente.” Zem.-Kalk-Gips, 5, 238–246.
Stark, J. (1995). “Sulfathüttenzement.” Wiss. Z. Hochsch. Archit. Bauwes. Weimar, 41(6/7), 7–15
Taylor, H. F. W. (1964). The chemistry of cements, 1st ed., Vol. 1, Academic Press, London.
Taylor, H. F. W. (1997). Cement chemistry, 2nd Ed., Thomas Telford, London.
USSC (2009). “U.S. Silica Company,” Industrial minerals. Berkeley Springs, WV.
Wu, X., Jiang, W., and Roy, D. M. (1990). “Early activation and properties of slag cement.” Cem. Concr. Res., 20(6), 961–974.
Yilmaz, E., Kesimal, A., and Ercikdi, B. (2003). “The factors affecting strength and stability of paste backfill.” Turkish J. An. Earth Sci., 28, 155–169 (in Turkish).
Zhou, Q., and Glasser, F. P. (2001). “Thermal stability and decomposition mechanisms of ettringite at .” Cem. Concr. Res., 31(9), 1333–1339.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 23 • Issue 5 • May 2011
Pages: 511 - 525
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Sep 4, 2009
Accepted: Oct 1, 2010
Published online: Oct 5, 2010
Published in print: May 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.