Effectiveness of Surface-Applied Corrosion Inhibitors for Concrete Bridges
Publication: Journal of Materials in Civil Engineering
Volume 23, Issue 3
Abstract
While the effectiveness of corrosion-inhibiting admixtures in new concrete has been well documented, there is little research on their surface-applied counterparts for existing structures. This study was undertaken to assess whether surface-applied products can delay, slow, or stop the corrosion process in contaminated concrete. A total of 348 specimens were tested using six commercially available corrosion inhibitors, at six levels of initial chloride content, and under two accelerated corrosive environments of salt-water spray and wet-dry cycles. Half of the specimens were intentionally cracked before applying the inhibitors, while the others were cracked afterward. Corrosion current and half-cell potential readings were taken weekly during the environmental exposure. Corroded bars were then assessed visually for surface rust and rib loss; and their mass loss and strength reduction were measured. Progression of chloride content over time was measured using companion concrete cubes. The inhibitors generally delayed the onset of corrosion and slowed the process, up to an initial chloride content of 0.5% by weight of cement. Each product seemed effective up to an extent in exposure time and the chloride content. However, no product stopped the corrosion process, and none purged chloride ions. The products may be most effective as preventive measures for fully hardened “virgin” concrete with initial chloride content below those specified to induce corrosion.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgements
Support for this study was provided by the North Carolina Department of Transportation and the Federal Highway Administration. The writers are grateful to the Materials and Test Unit of NCDOT for continuous support and valuable suggestions. The findings and opinions expressed here however are those of the writers, and not necessarily the views of the sponsoring agencies.
References
Aquron. (2002). “Aquron 7000 system.” Technical sheet, Aquron Corp., Rockwall, TX.
ASTM. (1999a). “Standard test method for determining the effects of chemical admixtures on the corrosion of embedded steel reinforcement in concrete exposed to chloride environments,” G 109-89 (R 99), West Conshohocken, PA.
ASTM. (1999b). “Standard test method for half-cell potentials for uncoated reinforcing steel in concrete.” C 876-91 (R 99), West Conshohocken, PA.
ASTM. (2003a). “Standard practice for preparing, cleaning, and evaluating corrosion test specimens.” G1-03, West Conshohocken, PA.
ASTM. (2003b). “Standard test method for acid-soluble chloride in mortar and concrete.” C 1152-03, West Conshohocken, PA.
ASTM. (2003c). “Standard test methods and definitions for mechanical testing of steel products.” A 370-03a, West Conshohocken, PA.
Axim. (1999). “Axim post III: Post treatment corrosion inhibitor and penetrating sealing compound for concrete.” Axim Italcementi Group-corrosion inhibitor products, Axim, Middlebranch, OH.
Bentur, A., Berke, N. S., and Diamond, S. (1997). Steel corrosion in concrete: Fundamentals and civil engineering practice, E & FN Spon, New York.
Brown, M. C. (1999). “Assessment of commercial corrosion inhibiting admixture for reinforced concrete.” M.Sc. thesis, Virginia Polytechnic Institute and State Univ., Blacksburg, VA.
ChemRex. (2002). “Sonocrete corrosion inhibitor: Surface applied migrating corrosion inhibitor.” Sonneborn Concrete Repair Systems, ChemRex, Shakopee, MN.
Clemena, G. G., and Virmani, P. (1998). “Corrosion protection—concrete bridges.” FHWA-RD-98-088, Federal Highway Administration, Washington, DC.
Cortec. (2001). “MCI: Migrating corrosion inhibitors for concrete structures.” Buyers Guide, Cortec Corp., St. Paul, MN.
Grace. (1999). “Postrite: A revolution in the battle against corrosion,” Application Guide, W. R. Grace, Cambridge, MA.
Mirmiran, A., Rizkalla, S. H., and Cook, A. (2004). “Corrosion inhibitors for concrete bridges.” FHWA/NC/2003-14, North Carolina State Dept. of Transportation.
Pullar-Strecker, P. (2002). “ICE design and practice guides.” Concrete reinforcement corrosion from assessment to repair decisions, Thomas Telford Publishing, London.
Sika. (2001). “Sika FerroGard 903: Penetrating corrosion inhibiting, impregnation coating for hardened concrete.” Product Information, Sika Corp., Lyndhurst, NJ.
Skold, R. V., and Larson, T. E. (1957). “Measurement of the instantaneous corrosion rate by means of polarization data.” Corrosion (Houston), 13(2), 139–142.
Sprinkler, M. M. (2003). “Final report Evaluation of corrosion inhibitors for concrete bridge deck patches and overlays.” VTRC 03-R14, Virginia Transportation Research Council, Charlottesville, VA, 36.
Virmani, Y. P., and Clemena, G. G. (1998). “Corrosion protection: Concrete bridges.” FHWA RD-98-088, Federal Highway Administration, Washington, DC.
Information & Authors
Information
Published In
Copyright
© 2011 American Society of Civil Engineers.
History
Received: Nov 28, 2008
Accepted: Aug 3, 2010
Published online: Aug 5, 2010
Published in print: Mar 1, 2011
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.