Technical Papers
May 11, 2020

Flow Characteristics and Hydraulic Performance of a Gun-Type Impact Sprinkler with and without Aeration

Publication: Journal of Irrigation and Drainage Engineering
Volume 146, Issue 7

Abstract

A water jet aeration method was used to address the problem of high water application rates for rotating impact sprinklers operating at low pressures at the distal end of the wetted radius that cause uneven water distribution. Based on a Jinlong Spray Irrigation Co. model PY20 impact sprinkler, a gas suction component was adopted to form an aeration impact sprinkler. The performance characteristics of the impact sprinkler with and without aeration were compared at operating pressure levels of 200 and 300 kPa. Additional tests on the water jet breakup characteristics of the two impact sprinkler types were conducted using high-speed photography techniques. The initial aeration lengths of the aeration impact sprinkler and two jet breakup lengths of both the aeration impact sprinkler and original impact sprinkler were studied. The experimental results demonstrated that the wetted radii of both impact sprinkler types were nearly the same at the same operating pressure and flow rate. The aeration method increased the water application rate at the midpoint of the wetted radius. At a lower operating pressure of 200 kPa, Christiansen’s uniformity coefficient increased to 68.5% for the aerated sprinkler and from 65.4% for the nonaerated impact sprinkler. The aeration impact sprinkler produced a larger average droplet diameter than that of the original impact sprinkler in the middle of the sprinkler profile, while the average droplet diameter toward the distal end of the profile was smaller. For the aeration impact sprinkler under operating pressure levels of 200 and 300 kPa, the aeration durations were 0.0137 and 0.007 s, and the initial aeration lengths were 7.7 and 8 mm, respectively. The jet breakup lengths were lower for the aeration impact sprinkler than for the original and increased with increasing operating pressure for both sprinkler types. The experimental results proved that the aeration impact sprinkler is not only feasible for agricultural irrigation, but it improves important performance characteristics at low operating pressures compared to a standard impact sprinkler.

Get full access to this article

View all available purchase options and get full access to this article.

Data Availability Statement

All data, models, and code generated or used during the study appear in the published article.

Acknowledgments

We are grateful for research funding from the National Natural Science Foundation of China (Nos. 51809119 and 51679109), the Natural Science Foundation of Jiangsu Province (BK20170555), the Natural Science Foundation of the Higher Education Institutions of Jiangsu Province (17KJB470001), and the Open Research Subject of Key Laboratory of Fluid and Power Machinery (Xihua University), Ministry of Education (szjj2019-017).

References

Bautista-Capetillo, C., O. Robles, H. Salinas, and E. Playán. 2014. “A particle tracking velocimetry technique for dropcharacterization in agricultural sprinklers.” Irrig. Sci. 32 (6): 437–447. https://doi.org/10.1007/s00271-014-0440-6.
Chen, C., L. D. Tang, Z. Gu, and Y. Tang. 2015. “Effect of finger on the irrigation quality in dices of lawn sprinklers.” [In Chinese.] Water Saving Irrig. J. 1: 20–23. https://doi.org/10.3969/j.issn.1007-4929.2015.01.006.
Christiansen, J. E. 1942. Irrigation by sprinkling. Berkley, CA: Univ. of California.
Deng, J., W. L. Xu, J. X. Qu, and Y. Q. Yang. 2002. “Influence of aeration on scouring.” [In Chinese.] J. Hydraul. Eng. 33 (10): 8–13. https://doi.org/10.13243/j.cnki.slxb.2002.10.002.
Gao, Z. Y. 2010. “The development of irrigation and drainage and technical research and extension in China.” [In Chinese.] Water Res. Hydropower Eng. 41 (12): 8–14. https://doi.org/10.13928/j.cnki.wrahe.2010.12.017.
Hu, S. G., and M. Z. Zhu. 1996. “The status and application of cavitating water jets.” [In Chinese.] J. Univ. Shanghai Sci. Technol. 18 (1): 1–8. https://doi.org/10.13255/j.cnki.jusst.1996.01.001.
ISO. 2012. Agricultural irrigation equipment-Sprinklers.Part 3: Characterization of distribution and test methods. ISO 15886-3. Geneva: ISO.
Issaka, Z., H. Li, Y. Jiang, P. Tang, C. Chen, and R. O. Darko. 2018. “Hydraulic performance characteristics of impact sprinkler with a fixed water dispersion device.” Int. J. Agric. Biol. Eng. 11 (6): 104–112. https://doi.org/10.25165/j.ijabe.20181106.4026.
James, R. D., and J. W. Jacobs. 1996. “A round turbulent jet produced by an oscillating diaphragm.” Phys. Fluids. 8 (9): 2484–2495. https://doi.org/10.1063/1.869040.
Jiang, Y., C. Chen, H. Li, and Q. J. Xiang. 2016. “Influences of nozzle parameters and low-pressure on jet breakup and droplet characteristics.” Int. J. Agric. Biol. Eng. 9 (4): 22–32. https://doi.org/10.3965/j.ijabe.20160904.2103.
Kincaid, D. C. 1991. “Impact sprinkler pattern modification.” Trans. ASAE. 34 (6): 2397–2403. https://doi.org/10.13031/2013.31885.
Lefebvre, A. H., and X. F. Wang. 1988. “Spray characteristics of aerated-liquid pressure atomizers.” J. Propul. Power. 4 (4): 293–298. https://doi.org/10.2514/3.23066.
Li, J. S., H. Kawano, and K. Yu. 1994. “Droplet size distributions from different shaped sprinkler nozzles.” Trans. ASAE. 37 (6): 1871–1878. https://doi.org/10.13031/2013.28278.
Li, X. S., J. B. Zhang, and W. T. Han. 2015. “Experiments on hydraulic performance of impact sprinkler with adjustable elevation angle.” [In Chinese.] Trans. Chin. Soc. Agric. Eng. 46 (2): 34–39. https://doi.org/10.6041/j.issn.1000-1298.2015.02.006.
Liu, J. P., S. Q. Yuan, H. Li, and X. Y. Zhu. 2011. “Combination uniformity improvement of impact sprinkler.” [In Chinese.] Trans. Chin. Soc. Agric. Eng. 27 (5): 107–111. https://doi.org/10.3969/j.issn.1002-6819.2011.07.018.
Liu, J. Z., and J. M. Zhu. 1993. “Study on the flow theory of cavitation water jet.” [In Chinese.] J. Hydraul. Eng. 15 (10): 33–38. https://doi.org/10.13243/j.cnki.slxb.1993.10.005.
Liu, L. S., H. Yang, J. X. Wu, and Y. Z. Yan. 2005. “Studies on breakup of liquid-sheet and spray characteristics downstream of the annular-spout effervescent atomizer.” [In Chinese.] J. Combust. Sci. Tech. 11 (2): 121–125. https://doi.org/10.3321/j.issn:1006-8740.2005.02.005.
Phukan, S., P. Kumar, J. Panda, B. R. Nayak, K. N. Tiwari, and R. P. Singh. 2001. “Application of drag reducing commercial and purified guargum for reduction of energy requirement of sprinkler irrigation and percolation rate of the soil.” Agric. Water Manage. 47 (2): 101–118. https://doi.org/10.1016/S0378-3774(00)00103-7.
Tang, P., H. Li, C. Chen, C. H. Zou, and Y. Jiang. 2015. “Arm movement law and hydraulic performance of vertical impact sprinkler with counterweight.” [In Chinese.] Trans. Chin. Soc. Agric. Eng. 31 (8): 37–44. https://doi.org/10.3969/j.issn.1002-6819.2015.02.006.
Wang, X., G. Li, C. C. Guo, W. T. Han, and X. M. Yao. 2015. “Optimization of impact sprinkler sub-nozzle parameters of elevation angle and position.” [In Chinese.] Trans. Chin. Soc. Agric. Eng. 31 (11): 89–95. https://doi.org/10.11975/j.issn.1002-6819.2015.11.013.
Wu, F., Y. S. Fan, S. M. Zai, and J. S. Li. 2004. “Manufacture of sprinkling irrigation machine with low water pressure and adjustable spraying range.” [In Chinese.] Water Saving Irrig. 3: 16–17. https://doi.org/10.3969/j.issn.1007-4929.2004.03.006.
Xu, H., S. H. Gong, R. Q. Jia, and X. A. Liu. 2010a. “Study on droplet size distribution of ZY sprinkler head.” [In Chinese.] J. Hydraul. Eng. 41 (12): 1416–1422. https://doi.org/10.13243/j.cnki.slxb.2010.12.013.
Xu, W. H., C. C. Gao, and H. X. Qin. 2010b. “Experimental study on performance of pulsed liquid jet pump.” [In Chinese.] Nucl. Power Eng. 31 (4): 48–51.
Xu, Y., J. Z. Ge, S. Y. Tian, S. Y. Li, L. N. R. Anthony, M. Zhan, and C. G. Cao. 2015. “Effects of water-saving irrigation practices and drought resistant rice variety on greenhouse gas emissions from a no-till paddy in the central lowlands of China.” Sci. Total Environ. 505 (Feb): 1043–1052. https://doi.org/10.1016/j.scitotenv.2014.10.073.
Yan, H. J., Z. Q. Liu, F. X. Wang, X. G. Yang, and M. Wang. 2007. “Research and development of impact sprinklers in China.” [In Chinese.] J. China Agric. Univ. 12 (1): 77–80. https://doi.org/10.3321/j.issn:1007-4333.2007.01.016.
Zhang, Y. S., D. L. Zhu, L. Zhang, and X. H. Gong. 2014. “Study on translocating speed and water distribution uniformity of lightweight lateral move irrigation system.” [In Chinese.] J. Drain. Irrig. Mach. Eng. 32 (7): 625–630. https://doi.org/10.3969/j.issn.1674-8530.13.0160.
Zhu, X. Y., S. Q. Yuan, J. Y. Jiang, J. P. Liu, and X. F. Liu. 2015. “Comparison of fluidic and impact sprinklers based on hydraulic performance.” Irrig. Sci. 33 (5): 367–374. https://doi.org/10.1007/s00271-015-0472-6.
Zhu, X. Y., S. Q. Yuan, and J. P. Liu. 2011. “Hydraulic performance of impact sprinkler type PY115 at low pressure.” [In Chinese.] Trans. Chin. Soc. Agric. Eng. 42 (11): 76–80.
Zou, X. X., Y. Li, C. Roger, Q. Z. Gao, Y. F. Wan, and X. B. Qin. 2013. “Cost-effectiveness analysis of water-saving irrigation technologies based on climate change response: A case study of China.” Agric. Water Manage. 129 (Nov): 9–20. https://doi.org/10.1016/j.agwat.2013.07.004.

Information & Authors

Information

Published In

Go to Journal of Irrigation and Drainage Engineering
Journal of Irrigation and Drainage Engineering
Volume 146Issue 7July 2020

History

Received: Jun 19, 2019
Accepted: Jan 30, 2020
Published online: May 11, 2020
Published in print: Jul 1, 2020
Discussion open until: Oct 11, 2020

Permissions

Request permissions for this article.

Authors

Affiliations

Assistant Research Fellow, Research Center of Fluid Machinery Engineering and Technology, Jiangsu Univ., Zhenjiang 212013, China; Assistant Research Fellow, Key Laboratory of Fluid and Power Machinery, Ministry of Education, Xihua Univ., Chengdu 610039, China (corresponding author). ORCID: https://orcid.org/0000-0003-4031-5587. Email: [email protected]
Qingjiang Xiang [email protected]
Associate Research Fellow, Research Center of Fluid Machinery Engineering and Technology, Jiangsu Univ., Zhenjiang 212013, China. Email: [email protected]
Research Fellow, Research Center of Fluid Machinery Engineering and Technology, Jiangsu Univ., Zhenjiang 212013, China. Email: [email protected]
Zhengdian Xu [email protected]
Doctoral Student, Research Center of Fluid Machinery Engineering and Technology, Jiangsu Univ., Zhenjiang 212013, China. Email: [email protected]

Metrics & Citations

Metrics

Citations

Download citation

If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.

View Options

Get Access

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Get Access

Access content

Please select your options to get access

Log in/Register Log in via your institution (Shibboleth)
ASCE Members: Please log in to see member pricing

Purchase

Save for later Information on ASCE Library Cards
ASCE Library Cards let you download journal articles, proceedings papers, and available book chapters across the entire ASCE Library platform. ASCE Library Cards remain active for 24 months or until all downloads are used. Note: This content will be debited as one download at time of checkout.

Terms of Use: ASCE Library Cards are for individual, personal use only. Reselling, republishing, or forwarding the materials to libraries or reading rooms is prohibited.
ASCE Library Card (5 downloads)
$105.00
Add to cart
ASCE Library Card (20 downloads)
$280.00
Add to cart
Buy Single Article
$35.00
Add to cart

Media

Figures

Other

Tables

Share

Share

Copy the content Link

Share with email

Email a colleague

Share