Design of Riverbank Riprap Using Large, Individually Placed Blocks
Publication: Journal of Hydraulic Engineering
Volume 145, Issue 12
Abstract
The protection of river banks in mountain rivers by riprap requires large blocks with weights typically exceeding 1 t. Thus, the blocks have to be placed individually. Such packed riprap has a relatively small spacing between the blocks. Consequently, the interlocking forces between the blocks are high, and the resistance of this protection to erosion is increased compared with traditional dumped riprap used for bank protection in low-grade rivers. Based on 98 systematical laboratory experiments, an adapted design method was developed for the case of riprap riverbank protection using large, individually placed blocks. Three different block sizes were tested by varying the longitudinal channel slope and bank inclination. For comparison, 34 tests were performed with dumped riprap. A design relationship is presented as a function of block size relative to the flow depth and a modified block Froude number considering the mean flow velocity. The additional resistance of riprap to erosion with large, individually placed blocks compared with dumped riprap is quantified. The proposed equations are compared with existing riprap sizing equations. The suggested method proved to be reliable in the assessment of the stability of packed riprap. Furthermore, it is shown that a second layer significantly delays riprap failure.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by the Swiss Federal Office for the Environment (FOEN) under Contract No. A2111.0239/10-Q8 0019.PJ/J372-1192.
References
Abt, S. R., and T. L. Johnson. 1991. “Riprap design for overtopping flow.” J. Hydraul. Eng. 117 (8): 959–972. https://doi.org/10.1061/(ASCE)0733-9429(1991)117:8(959).
Abt, S. R., C. I. Thornton, H. A. Gallegos, and C. M. Ullmann. 2008. “Round-shaped riprap stabilization in overtopping flow.” J. Hydraul. Eng. 134 (8): 1035. https://doi.org/10.1061/(ASCE)0733-9429(2008)134:8(1035).
Ahmed, A. F. 1987. “Stability of riprap side slopes in open channels.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Southampton.
Anderson, A. G., A. S. Paintal, and J. T. Davenport. 1970. Tentative design procedure for riprap lined channels. Minneapolis: Univ. of Minnesota.
Bezzola, G. R., and C. Hegg, eds. 2007. Ereignisanalyse Hochwasser 2005, Teil 1—Prozesse, Schäden und erste Einordnung. Bern, Switzerland: Bundesamt für Umwelt BAFU.
Bezzola, G. R., and C. Hegg, eds. 2008. Ereignisanalyse Hochwasser 2005, Teil 2—Analyse von Prozessen, Massnahmen und Gefahrengrundlagen. Bern, Switzerland: Bundesamt für Umwelt BAFU.
Blodgett, J. C., and C. E. McConaughy. 1986. Rock riprap design for protection of stream channels near highway structures; Volume 2, Evaluation of riprap design procedures. Sacramento, CA: USGS.
Brown, S. A., and E. S. Clyde. 1989. Design of riprap revetment. Hydraulic Engineering Circular 11. McLean, VA: Federal Highway Administration.
Chow, V. T. 1959. Open channel hydraulics. New York: McGraw-Hill.
De Almeida, G. A. M., and J. P. Martin-Vide. 2009. “Riprap stability: Transverse and longitudinal versus continues protections.” J. Hydraul. Eng. 135 (6): 447–456. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000031.
Escarameia, M., and R. W. P. May. 1992. Channel protection. Turbulence downstream of structures. London: HR Wallingford.
Froehlich, D. C. 2013. “Sizing loose rock riprap to protect stream bank.” River Res. Appl. 29 (2): 219–235. https://doi.org/10.1002/rra.1587.
Froehlich, D. C., and C. A. Benson. 1996. “Sizing dumped rock riprap.” J. Hydraul. Eng. 122 (7): 389–396. https://doi.org/10.1061/(ASCE)0733-9429(1996)122:7(389).
Grace, J. L., Jr., C. C. Calhoun, Jr., and D. N. Brown. 1973. Drainage and erosion control facilities: Field performance investigation. Vicksburg, MS: US Army Engineer Waterways Experiment Station.
Hiller, P. H., J. Aberle, and L. Lia. 2017. “Displacements as failure origin of placed riprap on steep slopes.” J. Hydraul. Res. 56 (2): 141–155. https://doi.org/10.1080/00221686.2017.1323806.
Isbash, S. V. 1935. Construction of dams by dumping stones in flowing water. Eastport, ME: War Dept., US Engineer Office, Engineering Division.
Jafarnejad, M., M. J. Franca, M. Pfister, and A. J. Schleiss. 2017a. “Time-based failure analysis of compressed riverbank riprap.” J. Hydraul. Res. 55 (2): 224–235. https://doi.org/10.1080/00221686.2016.1212940.
Jafarnejad, M., M. Pfister, E. Brühwiler, and A. J. Schleiss. 2017b. “Probabilistic failure analysis of riprap as riverbank protection under flood uncertainties.” J. Stochastic Environ. Res. Risk Assess. 31 (7): 1839–1851. https://doi.org/10.1007/s00477-016-1368-6.
Lagasse, P. F., P. E. Clopper, L. W. Zevenbergen, and J. F. Ruff. 2006. Riprap design criteria, recommended specifications, and quality control. Washington, DC: Transportation Research Board.
Lane, E. W. 1952. Progress report on results of studies on design of stable channels. Denver: Bureau of Reclamation.
Li, R. M., D. B. Simons, P. H. Blinco, and M. A. Samad. 1976. “Probabilistic approach to design of riprap riverbank protection.” In Vol. 1 of Proc., Symp. on Inland Waterways for Navigation, Flood Control, and Water Diversions, 1572–1591. Reston, VA: ASCE.
Maynord, S. T. 1992. Riprap stability: Studies in near-prototype size laboratory channel. Vicksburg, MS: US Army Engineer Waterways Experiment Station.
Maynord, S. T., and C. Neill. 2008. “Riprap design.” In Sedimentation engineering: ASCE manual and reports on engineering practice no. 110, edited by M. H. García, 1037–1056. Reston, VA: ASCE.
Maynord, S. T., J. F. Ruff, and S. R. Abt. 1989. “Riprap design.” J. Hydraul. Eng. 115 (7): 937–949. https://doi.org/10.1061/(ASCE)0733-9429(1989)115:7(937).
Maynord, S. T., J. F. Ruff, and S. R. Abt. 1991. “Closure of discussion on riprap design.” J. Hydraul. Eng. 117 (4): 542–544. https://doi.org/10.1061/(ASCE)0733-9429(1991)117:4(542.2).
Pilarczyk, K. W. 1990. “Coastal protection.” In Short course on coastal protection. Rotterdam, Netherlands: A.A. Balkema.
Racin, J. A., T. P. Hoover, and C. M. Crossett Avila. 2000. California bank and shore rock slope protection design: Practitioner’s guide and field evaluation of riprap methods. Sacramento, CA: Office of Structural Foundations, Transportation Laboratory.
Recking, A., and J. Pitlick. 2013. “Shields versus Isbash.” J. Hydraul. Eng. 139 (1): 51–54. https://doi.org/10.1061/(ASCE)HY.1943-7900.0000647.
Reese, A. 1984. “Riprap sizing four methods.” In Proc., ASCE Hydraulics Division Specialty Conf. New York: ASCE.
Richardson, E. V., and S. R. Davis. 2001. Evaluating scour at bridges. Washington, DC: Federal Highway Administration.
Schleiss, A. J. 2000. “Bemessung und Gestaltung von Blockwürfen an Gebirgsflüssen [Design and landscape integration of riprap in mountain rivers].” In Vol. 2 of Proc., Int. Symp. Interpraevent 2000, 351–360. Klagenfurt, Austria: Interpraevent.
Shields, A. 1936. Application of similarity principles and turbulence research to bed-load movement. Translated by W. P. Ott, and J. C. van Uchelen. Pasadena, CA: California Institute of Technology.
Simons, D. B., and F. Y. Senturk. 1992. Sediment transport technology. Fort Collins, CO: Water Resources Publications.
Stevens, M. A., D. B. Simons, and G. L. Lewis. 1976. “Safety factors for riprap protection.” J. Hydraul. Div. 102 (5): 637–655.
Stevens, M. A., D. B. Simons, and E. V. Richardson. 1984. “Riprap stability analysis.” Transp. Res. Rec. 950: 209–216.
Straub, L. G. 1953. “Dredge fills closure of Missouri River at Fort Randall.” In Proc., Minnesota Int. Hydraulics Convention, 61–75. Minneapolis: WMC Brown.
Ulrich, T. 1987. “Stability of rock protection on slopes.” J. Hydraul. Eng. 113 (7): 879–891. https://doi.org/10.1061/(ASCE)0733-9429(1987)113:7(879).
USACE. 1990. Hydraulic design of spillways. EM 1110-2-1603. Washington, DC: US Government Printing Office.
USACE. 1994. Hydraulic design of flood control channels. EM 1110-2-1601. Washington, DC: US Government Printing Office.
USBR (US Dept. of the Interior Bureau of Reclamation). 2014. Reclamation managing water in the West. Washington, DC: US Dept. of the Interior.
Wittler, R. J., and S. R. Abt. 1988. “Riprap design by modified safety factor method.” In Proc., 1988 National Conf. on Hydraulic Engineering, 143–148. Reston, VA: ASCE.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Sep 13, 2018
Accepted: Mar 29, 2019
Published online: Sep 30, 2019
Published in print: Dec 1, 2019
Discussion open until: Feb 29, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.