Geochemical Analysis of Leached Elements from Fly Ash Stabilized Soils
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 141, Issue 5
Abstract
Leaching controlling mechanisms of As, Ba, Ca, Cd, Mg, Se, and Sr from soil alone, fly ash alone, and soil-fly ash mixtures were investigated at a pH range of 1.5–14 through geochemical modeling. Results of the pH-static tests from previous studies indicated that As and Se concentrations increased at alkaline conditions, while Ca, Cd, Mg, and Sr concentrations increased when the pH of the aqueous solutions were acidic. Leaching of Ba tended to increase slightly at alkaline pH values. Effluent pH, oxidation-reduction (i.e., redox) potential , and element concentrations measured from pH-static tests were used as input data in the geochemical model. Geochemical modeling results indicated that release of the elements, except As and Se, are controlled by the dissolution and precipitation of oxide, hydroxide, sulfate, and carbonate solids of the elements. For a given element, these solids controlling the leaching of elements were very consistent regardless of soil and fly ash types. Model-based predictions indicated that leaching of Mg and Cd were controlled by carbonate minerals, and both carbonate and sulfate minerals were controlling solids for Ca, Ba, and Sr, depending on the pH of the leachate. According to the results of geochemical modeling analyses, leaching of As and Se were controlled by neither the dissolution nor precipitation of oxide, hydroxide solid minerals. The research reported in this paper suggests that the sorption mechanism was most probably controlling the leaching behavior of As and Se elements.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research reported in this paper was financially supported by the Federal Highway Administration (FHWA) Recycled Materials Resource Center (RMRC), Maryland State Highway Administration (MSHA), Maryland Water Resources Research Center (MWRRC), and Maryland Department of Natural Resources (MDNR). Endorsement by RMRC, MSHA, MWRRC, MDNR, nor the fly ash suppliers is implied, and should not be assumed. The writers thank Dr. William Balem for support during analyzing the results of the pH-dependent leaching tests and geochemical modeling analyses.
References
Allison, J. D., Brown, D. S., and Novo-Gradac, K. J. (1991). “MINTEQA2/PRODEFA2: A geochemical assessment model for environmental systems: Version 3.0 user’s manual.”, U.S. Environmental Protection Agency, Washington, DC.
Apul, D. S., Gardner, K. H., Eighmy, T. T., Fallman, A.-M., and Comans, R. N. J. (2005). “Simultaneous application of dissolution/precipitation and surface complexation/surface precipitation modeling to contaminant leaching.” Environ. Sci. Technol., 39(15), 5736–5741.
Archer, D. G. (1998). “Thermodynamic properties of import to environmental processes and remediation. I. Previous thermodynamic property values for cadmium and some of its compounds.” J. Phys. Chem. Ref. Data, 27(5), 915–946.
Ariese, F., et al. (2002). “Leaching studies of inorganic and organic compounds from fly ash.” Int. J. Environ. Anal. Chem., 82(11–12), 751–770.
ASTM. (2012). “Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete.” C618, West Conshohocken, PA.
ASTM. (2014). “Standard test methods for moisture, ash, and organic matter of peat and other organic soils.” D2974, West Conshohocken, PA.
Astrup, T., Dijkstra, J. J., Comans, R. N. J., Van der Sloot, H. A., and Christensen, T. H. (2006). “Geochemical modeling of leaching from MSWI air-pollution-control residues.” Environ. Sci. Technol., 40(11), 3551–3557.
Bin-Shafique, B., Benson, C. H., Edil, T. B., and Hwang, K. (2006). “Leachate concentrations from water leach and column leach tests on fly-ash stabilized soil.” Environ. Eng. Sci., 23(1), 53–67.
Bothe, J. V., and Brown, P. W. (1999). “The stabilities of calcium arsenates at 231 C.” J. Hazard. Mater., 69(2), 197–207.
Cetin, B. (2012). “Leaching of metals from high carbon fly ash mixed.” Ph.D. thesis, Univ. of Maryland, College Park, MD.
Cetin, B., and Aydilek, A. H. (2013). “pH and fly ash type effect on trace metal leaching from embankment soils.” Resour. Conserv. Recycl., 80, 107–117.
Cetin, B., Aydilek, A. H., and Guney, Y. (2010). “Stabilization of recycled base materials with high carbon fly ash.” Resour. Conserv. Recycl., 54(11), 878–892.
Cetin, B., Aydilek, A. H., and Guney, Y. (2012a). “Leaching of trace metals from high carbon fly ash stabilized highway base layers.” Resour. Conserv. Recycl., 58, 8–17.
Cetin, B., Aydilek, A. H., and Li, L. (2012b). “Experimental and numerical analysis of metal leaching from fly ash-amended highway bases.” Waste Manage., 32(5), 965–978.
Cetin, B., Aydilek, A. H., and Li, L. (2014). “Trace metal leaching from embankment soils amended with high-carbon fly ash.” J. Geotech. Geoenviron. Eng., 1–13.
Chittoori, B., Puppala, A., Wejrungsikul, T., and Hoyos, L. (2013). “Experimental studies on stabilized clays at various leaching cycles.” J. Geotech. Geoenviron. Eng., 1665–1675.
Cornelis, G., Poppe, S., Van Gerven, T., Van den Broeck, E., Ceulemans, M., and Vandecasteele, C. (2008). “Geochemical modelling of arsenic and selenium leaching in alkaline water treatment sludge from the production of non-ferrous metals.” J. Hazard. Mater., 159(2–3), 271–279.
Dijkstra, J. J., Van der Sloot, H. A., and Comans, R. N. J. (2002). “Process identification and model development of contaminant transport in MSWI bottom ash.” Waste Manage., 22(5), 531–541.
Eary, L. E., Rai, D., Mattigod, S. V., and Ainsworth, C. C. (1990). “Geochemical factors controlling the mobilization of inorganic constituents from fossil-fuel combustion residues: II. Review of the minor elements.” J. Environ. Qual., 19(2), 202–214.
Edil, T. B., Benson, C. H., Sazzad, B.-S., Tanyu, B. F., Kim, W.-H., and Senol, A. (2002). “Field evaluation of construction alternatives for roadways over soft subgrade.” Trans. Res. Rec., 1786, 36–48.
Electronic Code of Federal Regulations. (2015). 40 CFR 136, 〈〉 (Jan. 4, 2015).
Fruchter, J. S., Ral, D., and Zachara, J. M. (1990). “Identification of solubility-controlling solid phases in a large fly ash field lysimeter.” Environ. Sci. Technol., 24(8), 1173–1179.
Garavaglia, R., and Caramuscio, P. (1994). “Coal fly-ash leaching behaviour and solubility controlling solids.” Stud. Environ. Sci., 60, 87–102.
Iyer, R. S., Stanmore, B. R., and Pullammanappallil, P. C. (1999). “Solid-liquid mass transfer during leaching of calcium from dilute slurries of flyash. Chemical engineering research and design.” Trans. Inst. Chem. Eng. Part A, 77(8), 764–768.
Kirby, C. S., and Rimstidt, J. D. (1994). “Interaction of municipal solid waste ash with water.” Environ. Sci. Technol., 28(3), 443–451.
Komonweeraket, K., Benson, C. H., Edil, T. B., and Bleam, W. F., (2010). “Mechanisms controlling leaching of heavy metals from soil stabilized with fly ash.”, Geo Engineering Program, Univ. of Wisconsin, Madison, WI.
Komonweeraket, K., Benson, C. H., Edil, T. B., and Bleam, W. F. (2011). “Leaching behavior and mechanisms controlling the release of elements from soil stabilized with fly ash.” Proc., GeoFrontiers, ASCE, Reston, VA.
Komonweeraket, K., Cetin, B., Aydilek, A., Benson, C. H., and Edil, T. B. (2014). “Leaching characteristics of elements from fly ash mixed soils.” J. Fuel, in press.
Kosson, D. S., van der Sloot, H. A., and Eighmy, T. T. (1996). “An approach for estimation of contaminant release during utilization and disposal of municipal waste combustion residues.” J. Hazard. Mater., 47(1–3), 43–45.
Langmuir, D. (1997). Aqueous environmental geochemistry, Prentice-Hall, Upper Saddle River, NJ.
Mattigod, S. V., Rai, D., Eary, L. E., and Ainsworth, C. C. (1990). “Geochemical factors controlling the mobilization of inorganic constituents from fossil fuel combustion residues: I. Review of the major elements.” J. Environ. Qual., 19(2), 188–201.
McBride, M. B. (1994). Environmental chemistry of soils, Oxford University Press, New York.
Mudd, G. M., Weaver, T. R., and Kodikara, J. (2004). “Environmental geochemistry of leachate from leached brown coal ash.” J. Environ. Eng., 1514–1526.
Murarka, I. P., Rai, D., and Ainsworth, C. C. (1992). “Geochemical basis for predicting leaching of inorganic constituents from coal-combustion residues.” Waste Testing and Quality Assurance Symp., Washington, DC, 279–288.
Narukawa, T., Takatsu, A., Chiba, K., Riley, K. W., and French, D. H. (2005). “Investigation on chemical species of arsenic, selenium and antimony in fly ash from coal fuel thermal power stations.” J. Environ. Monit., 7(12), 1342–1348.
Reardon, E. J., Czank, C. A., Warren, C. J., Dayal, R., and Johnston, H. M. (1995). “Determining controls on element concentrations in fly ash leachate.” Waste Manage. Res., 13(5), 435–450.
Roy, W. R., and Griffin, R. A. (1984). “Illinois basin coal fly ashes.” Environ. Sci. Technol., 18(10), 739–742.
Sauer, J. J., Benson, C. H., Aydilek, A. H., and Edil, T. B. (2012). “Trace elements leaching from organic soils stabilized with high carbon fly ash.” J. Geotech. Geoenviron. Eng., 968–980.
Seames, W. S., and Wendt, J. O. L. (2000). “Partitioning of arsenic, selenium, and cadmium during the combustion of Pittsburgh and Illinois #6 coals in a self-sustained combustor.” Fuel Process. Technol., 63(2), 179–196.
Smith, R. M., and Martell, A. E. (1976). “Critical stability constants.” Inorganic complexes, Vol. 4, Plenum Press, New York.
Stumm, W., and Morgan, J. J. (1996). Aquatic chemistry: Chemical equilibria and rates in natural waters, Wiley, New York.
Taştan, E. O., Edil, T. B., Benson, C. H., and Aydilek, A. H. (2012). “Stabilization of organic soils with fly ash.” J. Geotech. Geoenviron. Eng., 819–833.
Theis, T. L., and Wirth, J. L. (1977). “Sorptive behavior of trace metals on fly ash in aqueous system.” Environ. Sci. Technol., 11(12), 1096–1100.
van der Hoek, E. E., van Elteren, J. T., and Comans, R. N. J. (1996). “Determination of As, Sb, and Se speciation in fly-ash leachates.” Int. J. Environ. Anal. Chem., 63(1), 67–79.
van der Sloot, H. A., Comans, R. N. J., and Hjelmar, O. (1996). “Similarities in the leaching behaviour of trace contaminants from waste, stabilized waste, construction materials and soils.” Sci. Total Environ., 178(1–3), 111.
van der Sloot, H. A., and Dijkstra, J. J. (2004). “Development of horizontally standardized leaching tests for construction materials: A material based or release based approach?”, Dutch Ministry of Housing, Spatial Planning, and the Environment, Amsterdam, Netherlands.
Wagemann, R. (1978). “Some theoretical aspects of stability and solubility of inorganic arsenic in freshwater environment.” Water Res., 12(3), 139–145.
Wang, J., Teng, X., Wang, H., and Ban, H. (2004). “Characterizing the metal adsorption capability of a Class F coal fly ash.” Environ. Sci. Technol., 38(24), 6710–6715.
Warren, C. J., and Dudas, M. J. (1984). “Weathering processes in relation to leachate properties of alkaline fly ash.” J. Environ. Qual., 13(4), 530–538.
Warren, C. J., and Dudas, M. J. (1985). “Formation of secondary minerals in artificially weathered fly ash.” J. Environ. Qual., 14(3), 405–410.
Xu, Y.-H., Nakajima, T., and Ohki, A. (2001). “Leaching of arsenic from coal fly ashes. 1. Leaching behavior of arsenic and mechanism study.” Toxicol. Environ. Chem., 81(1–2), 55–68.
Yan-Chu, H. (1994). Arsenic in the environment. Part I: Cycling and characterization, Wiley, New York.
Information & Authors
Information
Published In
Journal of Geotechnical and Geoenvironmental Engineering
Volume 141 • Issue 5 • May 2015
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jun 30, 2014
Accepted: Dec 16, 2014
Published online: Jan 27, 2015
Published in print: May 1, 2015
Discussion open until: Jun 27, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.