Compressibility of Recycled Materials for Use As Highway Embankment Fill
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 141, Issue 5
Abstract
Compressibility of recycled materials including bottom ash (BA), foundry slag (FSG), foundry sand (FSD), recycled asphalt pavement (RAP), recycled pavement material (RPM), recycled concrete aggregate (RCA), and recycled asphalt shingle (RAS) mixed with glacial outwash sand (GOS) was evaluated using one-dimensional (1D) compression tests. Results showed that except RCA, compressibility of all the compacted recycled materials is higher than that of the compacted GOS. Different compression mechanisms were attributed to each recycled material depending on the type, composition, and morphological characteristics of the particles. Bituminous recycled materials including RAP, RPM, and RAS-GOS mixtures exhibited relatively higher compressibility compared with nonbituminous recycled materials. At a constant vertical effective stress (), compression of the recycled materials increased over time with strain rates that are higher for bituminous recycled materials compared to nonbituminous recycled materials. The vertical strain rates () of all the recycled materials log-linearly increased with increasing . The slope of the curves, termed stress coefficient of compression, is independent of the elapsed time after loading. The stress coefficient of compression indicates degree of stress dependency for compression and is different for each recycled material. Secondary compression ratio is a power function of indicating that an embankment constructed with recycled materials settles at different rates along the embankment height. Temperature rises increased compressibility of the compacted RAP and RAS-GOS mixtures. On the other hand, thermal preloading significantly reduced the compressibility of the compacted RAP and RAS-GOS mixtures. Construction of embankments containing bituminous materials such as RAP, RPM, or RAS is recommended during summer to induce thermal preloading and reduce long-term settlement. Long-term settlements of typical highway embankments constructed with the recycled materials used in this study were below the allowable limit.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Support for this study was provided by the Recycled Materials Resource Center, which is supported by the Federal Highway Administration. The opinions, findings, conclusions, or recommendations expressed herein are those of the authors and do not necessarily represent the views of the sponsors.
References
Abichou, T., Benson, C. H., and Edil, T. B. (2000). “Foundry green sands as hydraulic barriers: Laboratory study.” J. Geotech. Geoenviron. Eng., 1174–1183.
ACAA (American Coal Ash Association). (2009). “Coal combustion product (CCP) production & use survey results.” Aurora, CO.
Ahmed, I. (1993). Use of waste material in highway construction, Noyes Data, Park Ridge, NJ.
Akisetty, C. K., Lee, S.-J., and Amirkhanian, S. N. (2009). “Effects of compaction temperature on volumetric properties of rubberized mixes containing warm-mix additives.” J. Mater. Civ. Eng., 409–415.
Alonso, E. S., Zamanillo, A. V., and Fresno, D. C. (2012). “Effect of type of compaction on mechanical properties in warm-mix asphalts.” J. Mater. Civ. Eng., 1043–1049.
American Foundry Society (AFS). (2014). “AFS-FIRST (Recycling).” 〈http://www.afsinc.org/government/AFSFirst.cfm〉 (Sep. 30, 2014).
ASTM. (1963). “Standard test method for particle-size analysis of soils.” D 422-63, West Conshohocken, PA.
ASTM. (1995). “Standard test method for measurement of hydraulic conductivity of porous material using a rigid-wall, compaction-mold permeameter.” D 5856-95, West Conshohocken, PA.
ASTM. (1996). “Standard test method for one-dimensional consolidation properties of soils.” D 2435-96, West Conshohocken, PA.
ASTM. (2000a). “Standard test methods for laboratory compaction characteristics of soil using standard effort [].” D 698-00a, West Conshohocken, PA.
ASTM. (2000b). “Standard test methods for specific gravity of soil solids by water pycnometer.” D 854-00, West Conshohocken, PA.
ASTM. (2000c). “Standard viscosity-temperature charts for asphalt.” D 2493-01, West Conshohocken, PA.
ASTM. (2008). “Standard specification for coal fly ash and raw or calcined natural pozzolan for use in concrete.” C 618-08, West Conshohocken, PA.
Azari, H., McCuen, R. H., and Stuart, K. D. (2003). “Optimum compaction temperature for modified binders.” J. Trans. Eng., 531–537.
Cao, L., Dong, L., and Sun, L. (2009). “Permanent deformation characteristic of asphalt mixture considering pavement temperature distribution.” Proc., 9th Int. Conf. Chinese Transp. Prof. (ICCTP), Critical Issues in Transportation Systems Planning, Development, and Management, Y. Wang, P. Yi, S. An, and H. Wang, eds., ASCE, Reston, VA, 1–8.
Carpenter, A. C., Gardner, K. H., Fopiano, J., Benson, C. H., and Edil, T. B. (2007). “Life cycle based risk assessment of recycled materials in roadway construction.” Waste Manage., 27(10), 1458–1464.
Chuhan, F. A., Kjeldstad, A., Bjorlykke, K., and Hoeg, K. (2003). “Experimental compression of loose sands: relevance to porosity reduction during burial in sedimentary basins.” Can. Geotech. J., 40(5), 995–1011.
Edil, T. B., and Fox, P. J. (1994). “Field test of thermal precompression.” Settlement ‘94, Specialty Conf. of the American Society of Civil Engineers, A. T. Yeung and G. Y. Félio, eds., Vol. 2, ASCE, Reston, VA, 1274–1286.
FHWA. (2008). “User guideline for byproducts and secondary use materials in pavement construction.”, U.S. Dept. of Transportation, 〈http://www.fhwa.dot.gov/pavement/pub_details.cfm?id=384〉 (Aug. 2014).
FIRST (Foundry Industry Recycling Starts Today). (2004). “Foundry sand facts for civil engineers.”, Federal Highway Administration, Washington, DC.
Fu, P., and Harvey, J. T. (2007). “Temperature sensitivity of foamed asphalt mix stiffness: field and lab study.” Int. J. Pave. Eng., 8(2), 137–145.
Fukumoto, T. (1992). “Particle breakage characteristics of granular soils.” Soils Found., 32(1), 26–40.
Gambatese, J. A., and Rajendran, S. (2005). “Sustainable roadway construction: energy consumption and material waste generation of roadways.” Proc., Construction Research Congress, I. D. Tommelein, ed., ASCE, Reston, VA, 1–13.
Goodhue, M. J., Edil, T. B., and Benson, C. H. (2001). “Interaction of foundry sands with geosynthetics.” J. Geotech. Geoenviron. Eng., 353–362.
Guthrie, S. W., Cooley, D., and Eggett, D. L. (2007). “Effects of reclaimed asphalt pavement on mechanical properties of base materials.”, Transportation Research Board, Washington, DC, 44–52.
Hagerty, M. M., Hite, D. R., Ullrich, C. R., and Hagerty, D. J. (1993). “One-dimensional high pressure compression of granular material.” J. Geotech. Geoenviron. Eng., 1–18.
Hansen, K. R., and Copeland, A. (2013). “Annual asphalt pavement industry survey on recycled materials and warm-mix asphalt Usage: 2009–2012.” National Asphalt Pavement Association (NAPA), Washington, DC.
Hanson, J. L. (1996). “Thermal precompression of peat.” Ph.D. dissertation, Univ. of Wisconsin-Madison, Madison, WI.
Holtz, R. D., Kovacs, W. D., and Sheahan, T. C. (2011). An introduction to geotechnical engineering, Pearson Education, Upper Saddle River, NJ.
Houston, S. L., Houston, W. N., and Williams, N. D. (1985). “Thermo-mechanical behaviour of seafloor sediments.” J. Geotech. Eng., 1249–1263.
Huang, H. W. (1990). “The use of bottom ash in highway embankments, subgrade, and subbases.”, Purdue Univ., West Lafayette, IN.
Javed, S., and Lovell, C. W. (1994). “Use of waste foundry sand in highway construction.”, Purdue School of Engineering, West Lafayette, IN.
Karimpour, H. (2012). “Time effects in relation to crushing in sand.” Ph.D. dissertation, Catholic Univ. of America, Washington, DC.
Kilbert, C. J. (2002). “Policy instruments for a sustainable built environment.” J. Land Use Environ. Law, 17(2), 379–394.
Kim, B., Prezzi, M., and Salgado, R. (2005). “Geotechnical properties of fly and bottom ash mixtures for use in highway embankments.” J. Geotech. Geoenviron. Eng., 914–924.
Kleven, J. R., Edil, T. B., and Benson, C. H. (2000). “Evaluation of excess foundry system sands for use as subbase material.”, Transportation Research Board, Washington, DC, 40–48.
Krivit, D. (2007). “Recycling of tear-off shingles: Best practices guide.” Construction Materials Recycling Association (CMRA), Aurora, IL.
Kuo, S.-S., Mahgoub, H. S., and Nazef, A. (2002). “Investigation of recycled concrete made with limestone aggregate for a base course in flexible pavement.”, Transportation Research Board, Washington, DC, 99–108.
LabView version 8.5 [Computer software]. National Instruments, Austin, TX.
Ladd, C. C., Foote, R., Ishihara, K., Schlosser, F., and Poulos, H. G. (1977). “Stress-deformation and strength characteristics.” State-of-the-Art Report, Proc., 9th Int. Conf. on Soil Mechanics and Foundation Engineering, Vol. 2, Tokyo, 421–494.
Lade, P. V., Liggio, C. D., Jr., and Nam, J. (2009). “Strain rate, creep and stress drop-creep experiments on crushed coral sand.” J. Geotech. Geoenviron. Eng., 941–953.
Lade, P. V., Nam, J., and Liggio, C. D., Jr. (2010). “Effects of particle crushing in stress drop-relaxation experiments on crushed coral sand.” J. Geotech. Geoenviron. Eng., 500–509.
Lade, P. V., Yamamuro, J. A., and Bopp, P. A. (1997). “Influence of time effects on instability of granular materials.” Comput. Geotech., 20(3–4), 179–193.
Lee, J., Edil, T., Tinjum, J., and Benson, C. (2010). “Quantitative assessment of environmental and economic benefits of using recycled construction materials in highway construction.”, Transportation Research Board, Washington, DC, 138–142.
Lee, K. L., and Farhoomand, I. (1967). “Compressibility and crushing of granular soil in anisotropic triaxial compression.” Can. Geotech. J., 4(1), 68–86.
Lee, S. J., Amirkhanian, S. N., Putman, B. J., and Kim, K. W. (2007). “Laboratory study of the effects of compaction on the volumetric and rutting properties of crm asphalt mixtures.” J. Mater. Civ. Eng., 1079–1089.
Marshal, R. J. (1967). “Large scale testing of rockfill materials.” J. Soil Mech. Found. Div., 93(SM2), 27–43.
Mast, D. G., and Fox, P. J. (1998). “Geotechnical performance of highway embankment constructed using waste foundry sand.”, JTRP, West Lafayette, IN, 66–85.
Mesri, G., and Castro, A. (1987). “The concept and during secondary compression.” J. Geotech. Eng., 230–247.
Mesri, G., Feng, T. W., and Benak, J. M. (1990). “Post densification penetration resistance of clean sands.” J. Geotech. Geoenviron. Eng., 1095–1115.
Mesri, G., and Godlewski, P. M. (1977). “Time and stress-compressibility interrelationship.” J. Geotech. Eng. Div., 103(5), 417–430.
Mesri, G., Stark, T. D., Ajlouni, M. A., and Chen, C. S. (1997). “Secondary compression of peat with or without surcharging.” J. Geotech. Geoenviron. Eng., 411–421.
Mesri, G., and Vardhanabhuti, B. (2009). “Compression of granular materials.” Can. Geotech. J., 46(4), 369–392.
NCHRP (National Cooperative Highway Research Program). (1971). “Construction of embankments.”, Transportation Research Board, National Research Council, Washington, DC, 38.
NCHRP (National Cooperative Highway Research Program). (1975). “Treatment of soft foundations for highway embankments.”, Transportation Research Board, National Research Council, Washington, DC, 25.
Palit, S. K., Reddy, K. S., and Pandey, B. B. (2004). “Laboratory evaluation of crumb rubber modified asphalt mixes.” J. Mater. Civ. Eng., 45–53.
Pestana, J. M., and Whittle, A. J. (1995). “Compression model for cohesionless soils.” Géotechnique, 45(4), 611–631.
RMRC (Recycled Materials Resource Center). (2014). “User guidelines for by-products and secondary use materials in pavement construction.”〈http://www.rmrc.unh.edu/tools/uguidelines/index.asp〉 (Aug. 2014).
Roberts, F. L., Kandhal, P. S., Brown, E. R., Lee, D. Y., and Kennedy, T. W. (1996). Hot mix asphalt materials, mixture design, and construction, National Asphalt Paving Association Education Foundation, Lanham, MD.
Roberts, J. E., and de Souza, J. M. (1958). The compressibility of sands, Vol. 58, Massachusetts Institute of Technology, MA, 1269–1277.
Shayan, A., and Xu, A. (2003). “Performance and properties of structural concrete made with recycled concrete aggregate.” ACI Mater. J., 100(5), 371–380.
Soleimanbeigi, A. (2012). “Geotechnical evaluation of recycled asphalt shingles as structural fill.” Ph.D. dissertation, Dept. of Civil Environmental Engineering, Univ. of Wisconsin-Madison, Madison, WI.
Soleimanbeigi, A., Edil, T. B., and Benson, C. H. (2013). “Evaluation of fly ash stabilization of recycled asphalt shingles for use in structural fills.” J. Mater. Civ. Eng., 94–104.
Soleimanbeigi, A., Edil, T. B., and Benson, C. H. (2014a). “Creep response of recycled asphalt shingles.” Can. Geotech. J., 51(1), 103–114.
Soleimanbeigi, A., Edil, T. B., and Benson, C. H. (2014b). “Engineering properties of recycled materials for use as embankment fill.” Geo-Congress 2014 Technical Papers: Geo-Characterization and Modeling for Sustainability, ASCE, Reston, VA, 3645–3657.
Sondag, M. S., Chadbourn, B. A., and Drescher, A. (2002). “Investigation of recycled asphalt pavement (RAP) mixtures.”, Minnesota Dept. of Transportation, St. Paul, MN.
Stark, T. D., Arellano, D., Horvath, J. S., and Leshchinsky, D. (2004). “Guidelines and recommended standards for geofoam applications in highway embankments.”, Transportation Research Board, National Research Council, Washington, DC.
Takei, T., Kusakabe, O., and Hayashi, T. (2001). “Time-dependent behaviour of crushable materials in one-dimensional compression tests.” Soils Found., 41(1), 97–121.
Tavakoli, M., and Soroushian, P. (1996). “Strengths of aggregate concrete made using field-demolished concrete as aggregate.” ACI Mater. J., 93(2), 182–190.
Tayebali, A. A., Tsai, B.-W., and Monismith, C. L. (1994). “Stiffness of asphalt-aggregate mixes.”, Strategic Highway Research Program, National Research Council, Washington, DC.
Terzaghi, K., Peck, R. B., and Mesri, G. (1996). Soil mechanics in engineering practice, 3rd Ed., Wiley, New York.
Thevanayagam, S., Shenthan, T., Mohan, S., and Liang, J. (2002). “Undrained fragility of clean sands, silty sands, and sandy silts.” J. Geotech. Geoenviron. Eng., 849–859.
Townsend, T., Powell, J., and Xu, C. (2007). “Environmental issues associated with asphalt shingle recycling.” Construction Materials Recycling Association, U.S. EPA Innovations Workgroup, Aurora, IL.
USBR (U.S. Bureau of Reclamation). (1987). “Design of small dams.” Denver.
USEPA (U.S. Environmental Protection Agency). (2009). “Potential for reducing greenhouse gas emissions in the construction sector.” 〈http://www.epa.gov/sectors/pdf/construction-sector-report.pdf〉 (Nov. 15, 2012).
USGS (U.S. Geological Survey). (2010). “Minerals yearbook.” 〉http://minerals.usgs.gov/minerals/pubs/commodity/iron_&_steel_slag/myb1-2008-fesla.pdf〉 (Dec. 10, 2010).
Viyanant, C. (2006). “Potential use of recycled asphalt pavement and crushed concrete as backfill for Mechanically Stabilized Earth (MSE) walls.” Ph.D. dissertation, Dept. of Civil Architectural and Environmental Engineering, Univ. of Texas-Austin, Austin, TX.
Viyanant, C., Rathje, E. M., and Rauch, F. A. (2007). “Creep of compacted recycled asphalt pavement.” Can. Geotech. J., 44(6), 687–697.
Wen, H., and Edil, T. (2009). “Sustainable reconstruction of highways with in-situ reclamation of materials stabilized for heavier loads.” 8th Int. Conf. on Bearing Capacity of Roads, Railways, and Airfields, Taylor and Francis, Boca Raton, FL.
Willis, J. R. (2013). “Reclaimed asphalt shingles characterization: Best practices.” National Center for Asphalt Technology (NCAT), Auburn Univ., Auburn, AL.
Wright, P. H. (1996). Highway engineering, Wiley, New York.
Yoon, S., Balunaini, U., Yildirim, I. Z., Prezzi, M., and Siddiki, N. Z. (2009). “Construction of an embankment with a fly and bottom ash mixture: Field performance study.” J. Mater. Civ. Eng., 271–278.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: May 5, 2014
Accepted: Dec 11, 2014
Published online: Jan 23, 2015
Published in print: May 1, 2015
Discussion open until: Jun 23, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.