Static Soil Resistance to Pipe Ramming in Granular Soils
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 141, Issue 3
Abstract
Pipe ramming is a cost-effective trenchless pipe installation method in which percussive blows generated by a pneumatically or hydraulically powered encased piston rammer are used to advance a pipe or culvert through the ground. To evaluate the feasibility of a pipe ramming installation, engineers must be able to reliably predict the pipe drivability and installation stresses. Assessment of the drivability of the pipe and selection of the optimal hammer for pipe ramming installation requires that the static and dynamic soil resistance to ramming at the pipe face and along the casing be reliably estimated. However, pipe ramming-specific models are not currently available, and engineers often resort to the existing traditional pipe-jacking and microtunneling models for static soil resistance computations. This paper describes the results of four full-scale pipes rammed in the field and the corresponding static soil resistance to ramming in granular soils. A companion paper addresses dynamic soil resistance and pipe drivability. The accuracy of the existing pipe jacking and microtunneling-based static soil resistance models is evaluated herein and found to provide unsatisfactory estimates of the face and casing resistance. New semiempirical pipe ramming-specific models are proposed based on the field observations and are found to produce good estimates of static soil resistance for use in pipe drivability evaluations.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge support from the Oregon DOT and Federal Highway Administration through Research Contract No. SPR-710. The research described in this paper was carried out with significant support from the Oregon and Southwest Washington Chapter of the National Utility Contractors Association. The authors are grateful for the support and donations provided by Gonzales Boring and Tunneling, J. W. Fowler Construction, Armadillo Underground, Emery & Sons, Inc., Wyo-Ben, Inc., RDO Equipment, Moore Excavation, and Peterson Machinery. The authors also gratefully acknowledge the helpful cooperation from the Wildish Sand and Gravel Company, the Ontario Ministry of Transportation, Golder Associates, and Jim Robinson Contracting. The authors are grateful for the comments by the anonymous reviewers, which served to improve the quality of this paper.
References
Allgemeine Technische Vertragsbedingungen für Bauleistungen (ATV). (1990). “Standard ATV-A 161E, structural calculation of driven pipes.” Gesellschaftzur Förderung der Abwassertechnik, German Association for the Water Environment, Bonn, Germany.
Ariaratnam, S. T., Chan, W., and Choi, D. (2006). “Utilization of trenchless construction methods in mainland China to sustain urban infrastructure.” Pract. Period. Struct. Des. Constr., 134–141.
ASTM. (2008). “Standard test method for high-strain dynamic testing of deep foundations.” D4945, West Conshohocken, PA.
Auld, F. A. (1982). “Determination of pipe jacking loads.” Proc., Pipe Jacking Association, Pipe Jacking Association, London.
Bennett, R. D. (1998). “Jacking forces and ground deformations associated with microtunneling.” Ph.D. thesis, Univ. of Illinois at Urbana–Champaign, Urbana, IL.
Briaud, J.-L., and Tucker, L. (1984). “Piles in sand: A method including residual stresses.” J. Geotech. Engrg., 1666–1680.
CAPWAP 2006-3 [Computer software]. Cleveland, Pile Dynamics.
Gavin, K. G., and O’Kelly, B. C. (2007). “Effect of friction fatigue on pile capacity in dense sand.” J. Geotech. Geoenviron. Eng., 63–71.
Goble, G. G., and Rausche, F. (1976). “Wave equation analysis of pile driving–WEAP program.” IP-76-14.1–IP-76-14.4, U.S. DOT, Federal Highway Administration, Washington, DC.
Golder Associates. (2010). “Foundation investigation report: Culvert site 6-Station 13+405, Township of Colborne.” Rep. No. 09-1132-0027-2000-R03, London, ON, Canada.
Holcomb, D. (2012). “Failing 96-inch diameter CMP replaced utilizing pipe ramming technology.” Proc., No-Dig Show 2012, North American Society for Trenchless Technology, Nashville, TN.
Lowery, L. L., Jr., Hirsch, T. J., Edwards, T. C., Coyle, H. M., and Samson, C. H., Jr. (1969). “Pile driving analysis—State of art.” Research Rep. No. 33-13, Texas A&M Univ., College Station, TX.
Marshall, M. (1998). “Pipe-jacked tunneling: Jacking loads and ground movements.” Ph.D. thesis, Magdalen College, Univ. of Oxford, Trinity, U.K.
Meskele, T. (2013). “Engineering design and analysis of pipe ramming installations.” Ph.D. dissertation, School of Civil and Construction Engineering, Oregon State Univ., Corvallis, OR.
Meskele, T., and Stuedlein, A. W. (2014a). “Analysis of a 610-mm-diameter pipe installed using pipe ramming.” J. Perform. Constr. Facil., 04014009.
Meskele, T., and Stuedlein, A. W. (2014b). “Drivability analyses for pipe-ramming installations.” J. Geotech. Geoenviron. Eng., 04014107.
Milligan, G. W. E., and Norris, P. (1994). Pipe jacking: Research results and recommendations, Pipe Jacking Association, London.
Miner, R. M. (2003). “Dynamic testing and analysis, Perham Creek Culvert Project, MP 57.5 Columbia River Highway, Hood River County, OR.” Letter Rep. Prepared for the Oregon DOT, Robert Miner Dynamic Testing (RMDT), Manchester, WA.
Najafi, M. (2008) “Pipe ramming projects.” ASCE manuals and reports on engineering practice No. 115, ASCE, Reston, VA.
Naval Facilities Engineering Command (NAVFAC). (1986). “Foundations and earth structures.” Design manual DM 7-02, Alexandria, VA.
Norris, P. (1992). “The behavior of jacked concrete pipes during site installation.” Ph.D. thesis, Pembrook College, Univ. of Oxford, Trinity, U.K.
Pellet-Beaucour, A.-L., and Kastner, R. (2002). “Experimental and analytical study of friction forces during microtunneling operations.” Tunn. Undergr. Space Technol., 17(1), 83–97.
Rausche, F., Likins, G., Liang, L., and Hussein, M. (2010). “Static and dynamic models for CAPWAP signal matching.” Proc., GeoFlorida 2010: Art of Foundation Engineering Practice, Geotechnical special publication 198, M. H. Hussein, J. B. Anderson, and W. M. Camp, eds., ASCE, Reston, VA, 534–553.
Rausche, F., Moses, F., and Goble, G. (1972). “Soil resistance predictions from pile dynamics.” J. Soil Mech. and Found. Div., 98(9), 917–937.
Samson, C. H., Jr., Hirsch, T. J., and Lowery, L. L., Jr. (1963). “Computer study of dynamic behavior of piling.” J. Struct. Div., 89(4), 413–450.
Simicevic, J., and Sterling, R. (2001). “Guidelines for pipe ramming.” Technical Rep. No. 2001.04, Trenchless Technology Center, Louisiana Tech Univ., Ruston, LA.
Smith, E. A. L. (1960). “Pile driving analysis by the wave equation.” J. Soil Mech. and Found. Div., 86(4), 35–64.
Staheli, K. (2006). “Jacking force prediction: An interface friction approach based on pipe surface roughness.” Ph.D. dissertation, Georgia Institute of Technology, Atlanta.
Stein, D. (2005). Trenchless technology for installation of cables and pipelines, Stein and Partner, Arnsberg, Germany.
Stuedlein, A. W., and Meskele, T. (2012). “Preliminary design and engineering of pipe ramming installations.” J. Pipeline Syst. Eng. Pract., 125–134.
Terzaghi, K. (1943). Theoretical soil mechanics, Wiley, New York.
Weber, W., and Hurtz, G. (1981). “Ermittlung der Rohrreibung und Entwicklung eines Bohrgerätes.” Tiefbau, Ingenieurbau, Straßenbau, 23(8), 550–555 (in German).
White, D. J., and Lehane, B. M. (2004). “Friction fatigue on displacement piles in sand.” Géotechnique, 54(10), 645–658.
Zubko, N. (2003). “Oregon project launches pipe ramming to the next level.” Trenchless Technology Magazine, Feb, 2–3.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: May 25, 2014
Accepted: Oct 1, 2014
Published online: Nov 3, 2014
Published in print: Mar 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.