Empirical Model for Shear Strength of Artificial Rock Containing a Single Nonpersistent Joint
Publication: International Journal of Geomechanics
Volume 21, Issue 8
Abstract
This paper proposes an empirical equation to evaluate the shear strength of rock mass with nonpersistent joints. A novel specimen preparation method is proposed and is used to created plaster specimens containing nonpersistent joints. Utilizing the proposed method, it is possible to create specimens with nonpersistent closed joints with different roughness levels along different directions. The normal stress applied to embedded nonpersistent joints is the key factor for estimating the joint friction contribution to the shear strength of rock mass with the joints. An analytical equation and an experimental approach are proposed to calculate the normal stress applied to the nonpersistent joints. Seemingly good agreement was found between the normal stress values obtained using the analytical equation and those measured by the experimental approach. To study the effects of four influential parameters, namely rock bridge ratio, material strength, joint roughness, and normal stress, on the shear strength of specimens with a single nonpersistent joint, an experimental layout was designed based on the Taguchi method. The results of the extensive experimental work were then expressed in terms of an empirical equation to calculate the shear strength of specimens embedding a single nonpersistent joint.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was supported by the Korea Institute of Energy Technology Evaluation and Planning (KETEP) and the Ministry of Trade, Industry & Energy (MOTIE) of the Republic of Korea (No. 20172510102340).
References
Antony, J. 2014. Design of experiments for engineers and scientists. 2nd ed. New York: Elsevier.
Asadizadeh, M., M. Moosavi, M. F. Hossaini, and H. Masoumi. 2018. “Shear strength and cracking process of nonpersistent jointed rocks: An extensive experimental investigation.” Rock Mech. Rock Eng. 51 (2): 415–428. https://doi.org/10.1007/s00603-017-1328-6.
Aydin, G., I. Karakurt, and K. Aydiner. 2013. “Prediction of the cut depth of granitic rocks machined by abrasive waterjet (AWJ).” Rock Mech. Rock Eng. 46 (5): 1223–1235. https://doi.org/10.1007/s00603-012-0307-1.
Bahaaddini, M., P. Hagan, R. Mitra, and B. K. Hebblewhite. 2016. “Numerical study of the mechanical behavior of nonpersistent jointed rock masses.” Int. J. Geomech. 16 (1): 04015035. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000510.
Bandis, S. C., A. C. Lumsden, and N. R. Barton. 1983. “Fundamentals of rock joint deformation.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 20 (6): 249–268. https://doi.org/10.1016/0148-9062(83)90595-8.
Barton, N. 1971. “A relationship between joint roughness and joint shear strength.” In Proc., Int. Symp. on Rock Mechanics, 1–8. Nancy, France: International Society for Rock Mechanics.
Barton, N. R. 1972. “A model study of rock-joint deformation.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 9 (5): 579–582. https://doi.org/10.1016/0148-9062(72)90010-1.
Barton, N. 1976. “The shear strength of rock and rock joints.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 13 (9): 255–279. https://doi.org/10.1016/0148-9062(76)90003-6.
Barton, N., and V. Choubey. 1977. “The shear strength of rock joints in theory and practice.” Rock Mech. 10 (1): 1–54. https://doi.org/10.1007/BF01261801.
Chen, N., X. Zhang, Q. Jiang, X. Feng, W. Wei, and B. Yi. 2018a. “Shear behavior of rough rock joints reinforced by bolts.” Int. J. Geomech. 18 (1): 04017130. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001048.
Chen, X., S. Zhang, and C. Cheng. 2018b. “Numerical study on effect of joint strength mobilization on behavior of rock masses with large nonpersistent joints under uniaxial compression.” Int. J. Geomech. 18 (11): 04018140. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001260.
Cheng, Y., L. N. Y. Wong, and C. Zou. 2015. “Experimental study on the formation of faults from en-echelon fractures in Carrara Marble.” Eng. Geol. 195: 312–326. https://doi.org/10.1016/j.enggeo.2015.06.004.
Coulomb, C. 1773. “Test on the applications of the rules of maxima and minima to some problems of statics related to architecture.” Mem. Math. Phys. 7: 343–382.
Deng, Q., and P. Zhang. 1984. “Research on the geometry of shear fracture zones.” J. Geophys. Res.: Solid Earth 89 (B7): 5699–5710. https://doi.org/10.1029/JB089iB07p05699.
Fereshtenejad, S. 2020. “Fundamental study on shear behavior of non-persistent joints.” Ph.D. thesis, Dept. of Energy Systems Engineering, Seoul National Univ.
Fereshtenejad, S., and J.-J. Song. 2016. “Fundamental study on applicability of powder-based 3D printer for physical modeling in rock mechanics.” Rock Mech. Rock Eng. 49 (6): 2065–2074. https://doi.org/10.1007/s00603-015-0904-x.
Fereshtenejad, S., and J. J. Song. 2021. “Applicability of powder-based 3D printing technology in shear behavior analysis of rock mass containing nonpersistent joints.” J. Struct. Geol. 143: 104251. https://doi.org/10.1016/j.jsg.2020.104251.
Fisher, R. A. 1949. The design of experiments. 5th ed. Oxford: Oliver & Boyd.
Franz, J. 2009. An investigation of combined failure mechanisms in large scale open pit slopes. Sydney, Australia: Univ. of New South Wales.
Gao, Y., and L. N. Y. Wong. 2014. “A re-examination of the Joint Roughness Coefficient (JRC) and its correlation with the roughness parameter Z2.” In Proc., 48th U.S. Rock Mechanics/Geomechanics Symp., Minneapolis, MN: American Rock Mechanics Association.
Ge, Y., H. Tang, M. A. M. Ez Eldin, L. Wang, Q. Wu, and C. Xiong. 2017. “Evolution process of natural rock joint roughness during direct shear tests.” Int. J. Geomech. 17: 5.
Gehle, C., and H. K. Kutter. 2003. “Breakage and shear behaviour of intermittent rock joints.” Int. J. Rock Mech. Min. Sci. 40 (5): 687–700. https://doi.org/10.1016/S1365-1609(03)00060-1.
Ghazvinian, A., M. R. Nikudel, and V. Sarfarazi. 2007. “Effect of rock bridge continuity and area on shear behavior of joints.” In Proc., 11th ISRM Congress, 247–250. Lisbon, Portugal: International Society for Rock Mechanics and Rock Engineering.
Ghazvinian, A., V. Sarfarazi, W. Schubert, and M. Blumel. 2012. “A study of the failure mechanism of planar non-persistent open joints using PFC2D.” Rock Mech. Rock Eng. 45 (5): 677–693.
Goktan, R. M., and N. Gunes Yilmaz. 2005. “A new methodology for the analysis of the relationship between rock brittleness index and drag pick cutting efficiency.” J. South. Afr. Inst. Min. Metall. 105 (10): 727–733.
Jennings, J. E. 1970. “A mathematical theory for the calculation of the stability of slopes in open cast mines.” In Proc., Planning Open Pit Mines, 87–102. Cape Town: AA Balkema.
Jiang, M., J. Liu, G. B. Crosta, and T. Li. 2017. “DEM analysis of the effect of joint geometry on the shear behavior of rocks.” C. R. Méc. 345 (11): 779–796. https://doi.org/10.1016/j.crme.2017.07.004.
Jiang, Y., P. Yan, Y. Wang, H. Luan, and Y. Chen. 2020. “Numerical investigations on shear behavior and failure mechanism of nonpersistent jointed rocks.” Geotech. Geol. Eng. 38 (2): 1639–1651. https://doi.org/10.1007/s10706-019-01119-1.
Kanafi, M. M. 2016. “Surface generator: artificial randomly rough surfaces.” MATLAB Central File Exchange. Accessed September 15, 2020. https://www.mathworks.com/matlabcentral/fileexchange/60817-surface-generator-artificial-randomly-rough-surfaces.
Kim, B. H., P. K. Kaiser, and G. Grasselli. 2007. “Influence of persistence on behaviour of fractured rock masses.” Geol. Soc. London, Spec. Publ. 284 (1): 161–173. https://doi.org/10.1144/SP284.11.
Ladanyi, B., and G. Archambault. 1969. Simulation of shear behavior of a jointed rock mass. Houston: American Rock Mechanics Association.
Lajtai, E. Z. 1969a. “Strength of discontinuous rocks in direct shear.” Géotechnique 19 (2): 218–233. https://doi.org/10.1680/geot.1969.19.2.218.
Lajtai, E. Z. 1969b. “Shear strength of weakness planes in rock.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 6 (5): 499–515. https://doi.org/10.1016/0148-9062(69)90016-3.
Lajtai, E. Z., B. J. Carter, and E. J. S. Duncan. 1994. “En echelon crack-arrays in potash salt rock.” Rock Mech. Rock Eng. 27 (2): 89–111. https://doi.org/10.1007/BF01020207.
Lee, Y.-K., J.-W. Park, and J.-J. Song. 2014. “Model for the shear behavior of rock joints under CNL and CNS conditions.” Int. J. Rock Mech. Min. Sci. 70: 252–263. https://doi.org/10.1016/j.ijrmms.2014.05.005.
Min, K.-B., J. Rutqvist, C.-F. Tsang, and L. Jing. 2004. “Stress-dependent permeability of fractured rock masses: A numerical study.” Int. J. Rock Mech. Min. Sci. 41 (7): 1191–1210. https://doi.org/10.1016/j.ijrmms.2004.05.005.
Montgomery, D. C. 2017. Design and analysis of experiments. Hoboken, NJ: John Wiley & Sons.
Muralha, J., G. Grasselli, B. Tatone, M. Blümel, P. Chryssanthakis, and J. Yujing. 2015. “ISRM suggested method for laboratory determination of the shear strength of rock joints: Revised version.” In The ISRM suggested methods for rock characterization, testing and monitoring: 2007–2014, edited by R. Ulusay, 131–142. Cham, Switzerland: Springer.
Naghadehi, Z. M., R. Jimenez, R. KhaloKakaie, and S.-M. E. Jalali. 2013. “A new open-pit mine slope instability index defined using the improved rock engineering systems approach.” Int. J. Rock Mech. Min. Sci. 61: 1–14. https://doi.org/10.1016/j.ijrmms.2013.01.012.
O’Reilly, K. J. 1980. “The effect of joint plane persistence on rock slope reliability.” Ph.D. thesis, Dept. of Civil Engineering, Massachusetts Institute of Technology.
Patton, F. D. 1966. Multiple modes of shear failure in rock. Richardson, TX: International Society for Rock Mechanics and Rock Engineering.
Savilahti, T., E. Nordlund, and O. Stephansson. 1990. “Shear box testing and modeling of joint bridge.” In Proc., Int. Symp. on Rock Joints, 295–300. Boca Raton, FL: CRC Press.
Segall, P., and D. D. Pollard. 1983. “Nucleation and growth of strike slip faults in granite.” J. Geophys. Res.: Solid Earth 88 (B1): 555–568. https://doi.org/10.1029/JB088iB01p00555.
Seidel, J. P., and C. M. Haberfield. 2002. “A theoretical model for rock joints subjected to constant normal stiffness direct shear.” Int. J. Rock Mech. Min. Sci. 39 (5): 539–553. https://doi.org/10.1016/S1365-1609(02)00056-4.
Shang, J., Z. Zhao, J. Hu, and K. Handley. 2018. “3D particle-based DEM investigation into the shear behaviour of incipient rock joints with various geometries of rock bridges.” Rock Mech. Rock Eng. 51 (11): 3563–3584. https://doi.org/10.1007/s00603-018-1531-0.
Sjöberg, J. 1996. Large scale slope stability in open pit mining : A review. Luleå, Sweden: Luleå tekniska universitet.
Song, J.-J. 2009. “Distribution-free method for estimating size distribution and volumetric frequency of rock joints.” Int. J. Rock Mech. Min. Sci. 46 (4): 748–760. https://doi.org/10.1016/j.ijrmms.2008.10.004.
Stimpson, B. 1978. Failure of slopes containing discontinuous planar points. Houston: American Rock Mechanics Association.
Taguchi, G., S. Chowdhury, and Y. Wu. 2005. Taguchi’s quality engineering handbook. CERN Document Server. Hoboken, NJ: Wiley.
Tchalenko, J. S., and N. N. Ambraseys. 1970. “Structural analysis of the Dasht-e Bayaz (Iran) earthquake fractures.” Geol. Soc. Am. Bull. 81 (1): 41–60. https://doi.org/10.1130/0016-7606(1970)81[41:SAOTDB]2.0.CO;2.
Tiryaki, B. 2006. “Evaluation of the indirect measures of rock brittleness and fracture toughness in rock cutting.” J. South. Afr. Inst. Min. Metall. 106 (6): 407–423.
Tse, R., and D. M. Cruden. 1979. “Estimating joint roughness coefficients.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 16 (5): 303–307. https://doi.org/10.1016/0148-9062(79)90241-9.
Ulusay, R. (Ed.). 2015. The ISRM Suggested Methods for Rock Characterization, Testing and Monitoring: 2007–2014. Cham, Switzerland: Springer.
Wong, R. H. C., W. L. Leung, and S. W. Wang. 2001. Shear strength studies on rock-like models containing arrayed open joints. Houston: American Rock Mechanics Association.
Zhang, H. Q., Z. Y. Zhao, C. A. Tang, and L. Song. 2006. “Numerical study of shear behavior of intermittent rock joints with different geometrical parameters.” Int. J. Rock Mech. Min. Sci. 43 (5): 802–816. https://doi.org/10.1016/j.ijrmms.2005.12.006.
Zhang, L., and H. H. Einstein. 2010. “The planar shape of rock joints.” Rock Mech. Rock Eng. 43 (1): 55–68. https://doi.org/10.1007/s00603-009-0054-0.
Zhang, X. 1990. “Shear resistance of en-echelon jointed rock masses in joint direction.” Int. J. Min. Geol. Eng. 8 (1): 1–12. https://doi.org/10.1007/BF00881124.
Zhang, X., Q. Jiang, P. H. S. W. Kulatilake, F. Xiong, C. Yao, and Z. Tang. 2019. “Influence of asperity morphology on failure characteristics and shear strength properties of rock joints under direct shear tests.” Int. J. Geomech. 19 (2): 04018196. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001347.
Zhao, J. 1997a. “Joint surface matching and shear strength part A: Joint matching coefficient (JMC).” Int. J. Rock Mech. Min. Sci. 34 (2): 173–178. https://doi.org/10.1016/S0148-9062(96)00062-9.
Zhao, J. 1997b. “Joint surface matching and shear strength part B: JRC-JMC shear strength criterion.” Int. J. Rock Mech. Min. Sci. 34 (2): 179–185. https://doi.org/10.1016/S0148-9062(96)00063-0.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: May 17, 2020
Accepted: Mar 11, 2021
Published online: May 19, 2021
Published in print: Aug 1, 2021
Discussion open until: Oct 19, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Mostafa Asadizadeh, Mahdi Moosavi, Mohammad Farouq Hossaini, Ahmadreza Hedayat, Taghi Sherizadeh, Hossein Masoumi, Numerical Modeling of Rock Blocks with Nonpersistent Rough Joints Subjected to Uniaxial Compressive and Shear Loadings, International Journal of Geomechanics, 10.1061/IJGNAI.GMENG-7858, 23, 7, (2023).
- Shan Dong, Yulin Peng, Zhichun Lu, Heng Zhang, Weihua Hou, Aijun Su, Shear characteristics and shear strength model of rock mass structural planes, Scientific Reports, 10.1038/s41598-022-17998-z, 12, 1, (2022).