Load-Transfer Mechanism of Helical Piles Under Compressive and Impact Loading
Publication: International Journal of Geomechanics
Volume 21, Issue 6
Abstract
Helical piles are currently used to support large compressive loads, which requires accurate evaluation of their bearing capacity. High strain dynamic load testing is increasingly used to determine the capacity of helical piles. However, the load-transfer mechanism of helical piles under impact loading has never been thoroughly examined. In this study, the load-transfer mechanism and the interpreted ultimate bearing capacity at 12%, 10%, 8%, and 5% of helix-diameter failure criteria of helical piles installed in cohesionless and cohesive soils under both axial static and impact dynamic loading are investigated numerically. Three-dimensional nonlinear finite element models are developed and verified against two case studies. The verified models are employed to conduct a parametric study covering a range of helical pile configurations. The results showed that the load-transfer mechanism depends on the spacing ratio and the selected failure criteria. Furthermore, the limit equilibrium method overestimates and underestimates the bearing capacity for helical piles installed in cohesionless and cohesive soils, respectively, compared with the numerically predicted values.
Get full access to this article
View all available purchase options and get full access to this article.
References
Al-Baghdadi, T. 2018. “Screw piles as offshore foundations: Numerical and physical modelling.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Dundee.
Ali, O. K., and H. O. Abbas. 2019. “Performance assessment of screw piles embedded in soft clay.” Civil Engineering Journal 5 (8): 1788–1798. https://doi.org/10.28991/cej-2019-03091371.
Alpan, I. 1970. “The geotechnical properties of soils.” Earth Sci. Rev. 6 (1): 5–49. https://doi.org/10.1016/0012-8252(70)90001-2.
Alwalan, M. F., and M. H. El Naggar. 2020. “Finite element analysis of helical piles subjected to axial impact loading.” Comput. Geotech. 123: 103597. https://doi.org/10.1016/j.compgeo.2020.103597.
Anbazhagan, P., A. Uday, S. S. R. Moustafa, and N. S. N. Al-Arifi. 2017. “Soil void ratio correlation with shear wave velocities and SPT N values for Indo-Gangetic basin.” J. Geol. Soc. India 89 (4): 398–406. https://doi.org/10.1007/s12594-017-0621-z.
Bagheri, F., and M. H. El Naggar. 2015. “Effects of installation disturbance on behavior of multi-helix piles in structured clays.” DFI J. 9 (2): 80–91. https://doi.org/10.1179/1937525515Y.0000000008.
Bak, J., B. H. Choi, J. Lee, J. Bae, K. Lee, and D. Kim. 2019. “Behaviour of single and group helical piles in sands from model experiments.” In Vol. 278 of Proc., MATEC Web of Conf. Les Ulis, France: EDP Sciences.
Basarkar, S. S., M. Kumar, and R. Vaidya. 2011. “High strain dynamic pile testing practices in India-favourable situations and correlation studies.” In Proc., Indian Geotechnical Conf., 1039–1042. Kochi, India: Indian Geotechnical Society.
Begemann, H. K. S. 1974. “General report for Central and Western Europe.” In Proc., European Symp. on Penetration Testing, 9–39. Stockholm, Sweden: National Swedish Building Research
Beim, J., and S. C. Luna. 2012. “Results of dynamic and static load tests on helical piles in the varved clay of Massachusetts.” DFI J. 6 (1): 58–67. https://doi.org/10.1179/dfi.2012.005.
Bentley Systems. 2019. PLAXIS 2d geotechnical finite element analysis software. Advancing Infrastructure. Delft, Netherlands: Bentley Systems.
Bowles, L. E. 1996. Foundation analysis and design, 66–190. New York: McGraw-Hill.
Clayton, D. J. 2005. Basic helical screw pile design, 1–28. ECP Torque Anchor Brand of Helical Screw Piles. Olathe, KS: Earth Contact Products.
Cannon, J. G. 2000. “The application of high strain dynamic pile testing to screwed steel piles.” In Proc., 6th Int. Conf. on the Application of Stress-Wave Theory to Piles, 393–398. Rotterdam, Netherlands: Taylor & Francis Group/A.A. Balkema.
CH2M Hill. 2013. Geotechnical report for the APE yard helical pile test program. Rep. No. SEA130450001/ES020513062946SEA. Bellevue, WA: CH2M Hill.
Denver, H. 1982. “Modulus of elasticity for sand determined by SPT and CPT.” In Vol. 1 of Proc., 2nd European Symp. on Penetration Testing, 35–40. Amsterdam, The Netherlands: Taylor & Francis Group.
Dikmen, Ü. 2009. “Statistical correlations of shear wave velocity and penetration resistance for soils.” J. Geophys. Eng. 6 (1): 61–72. https://doi.org/10.1088/1742-2132/6/1/007.
Elkasabgy, M. A. 2011. “Dynamic and static performance of large-capacity helical piles in cohesive soils.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Univ. of Western Ontario, Electronic Thesis and Dissertation Repository.
Elkasabgy, M. A., and M. H. El Naggar. 2013. “Dynamic response of vertically loaded helical and driven steel piles.” Can. Geotech. J. 50 (5): 521–535. https://doi.org/10.1139/cgj-2011-0126.
Elkasabgy, M., and M. H. El Naggar. 2015. “Axial compressive response of large-capacity helical and driven steel piles in cohesive soil.” Can. Geotech. J. 52 (2): 224–243. https://doi.org/10.1139/cgj-2012-0331.
El Naggar, M. H., and Y. Abdelghany. 2007. “Helical screw piles (HSP) capacity for axial cyclic loadings in cohesive soils.” In Proc., 4th Int. Conf. on Earthquake Geotechnical Engineering, paper 1567. Thessaloniki, Greece: ISSMGE.
El Sharnouby, M. M., and M. H. El Naggar. 2012. “Field investigation of axial monotonic and cyclic performance of reinforced helical pulldown micropiles.” Can. Geotech. J. 49 (5): 560–573. https://doi.org/10.1139/t2012-017.
Elsherbiny, Z. H., and M. H. El Naggar. 2013. “Axial compressive capacity of helical piles from field tests and numerical study.” Can. Geotech. J. 50 (12): 1191–1203. https://doi.org/10.1139/cgj-2012-0487.
Fakharian, K., S. F. Masouleh, and A. S. Mohammadlou. 2014. “Comparison of end-of-drive and restrike signal matching analysis for a real case using continuum numerical modelling.” Soils Found. 54 (2): 155–167. https://doi.org/10.1016/j.sandf.2014.02.007.
Fateh, A. M. A., A. Eslami, and A. Fahimifar. 2017. “Direct CPT and CPTu methods for determining bearing capacity of helical piles.” Mar. Georesour. Geotechnol. 35 (2): 193–207. https://doi.org/10.1080/1064119X.2015.1133741.
Feizee, S. 2008. “Evaluation of design parameters of pile using dynamic testing and analyses.” Ph.D. thesis, Dept. of Civil and Environment Engineering, Amirkabir Univ. of Technology.
Fujiwara, T. 1972. “Estimation of ground movements in actual destructive earthquakes.” In Proc., 4th European Symp. on Earthquake Engineering, 125–132. Imperial College, London: Bulgarian Academy of Sciences.
Gavin, K., P. Doherty, and A. Tolooiyan. 2014. “Field investigation of the axial resistance of helical piles in dense sand.” Can. Geotech. J. 51 (11): 1343–1354. https://doi.org/10.1139/cgj-2012-0463.
George, B. E., S. Banerjee, and S. R. Gandhi. 2017. “Numerical analysis of helical piles in cohesionless soil.” Int. J. Geotech. Eng. 14 (4): 361–375. https://doi.org/10.1080/19386362.2017.1419912.
Gibson, G. C., and H. M. Coyle. 1968. Soil damping constants related to common soil properties in sands and clays. Bryan, TX: Texas Transportation Institute.
Green, T. A., and M. L. Kightley. 2005. “CAPWAP testing-theory and application.” In Vol. 16 of Proc. Int. Conf. on Soil Mechanics and Geotechnical Engineering. Rotterdam, Netherlands: AA Balkema.
Gunaratne, M. 2013. The foundation engineering handbook. Boca Raton, FL: CRC Press.
Harnish, J., and M. H. El Naggar. 2017. “Large-diameter helical pile capacity – torque correlations.” Can. Geotech. J. 54 (7): 968–986. https://doi.org/10.1139/cgj-2016-0156.
Hasancebi, N., and R. Ulusay. 2007. “Empirical correlations between shear wave velocity and penetration resistance for ground shaking assessments.” Bull. Eng. Geol. Environ. 66 (2): 203–213. https://doi.org/10.1007/s10064-006-0063-0.
Hird, C. C., and S. A. Stanier. 2010. “Modelling helical screw piles in clay using a transparent soil.” In Proc., 7th Int. Conf. on Physical Modelling in Geotechnics, 769–774. Zurich, Switzerland: CRC Press.
Holscher, P., H. Brassinga, M. Brown, P. Middendorp, M. Profittlich, and F. A. Van Tol. 2011. Rapid load testing on piles: Interpretation guidelines. Boca Raton, FL: CRC Press.
Imai, T. 1977. “P and S wave velocities of the ground in Japan.” In Vol. 2 of Proc., IX Int. Conf. on Soil Mechanics and Foundation Engineering, 127–132. Tokyo: Japanese Society of Soil Mechanics and Foundation Engineering.
Imai, T., H. Fumoto, and K. Yokota. 1975. “The relation of mechanical properties of soils to P- and S-wave velocities in Japan.” In Proc., 4th Japanese Earthquake Engineering Symp., translated by H. Umehara [In Japanese.] 86–96. Tokyo: Japan Association for Earthquake Engineering.
Jinan, Z. 1987. “Correlation between seismic wave velocity and the number of blow of SPT and depth.” In Selected Papers from the Chinese Journal of Geotechnical Engineering, 92–100. Nanjing, China: American Society of Civil Engineers.
Justason, M. D. 1997. Report of load testing at the Taipei municipal incinerator expansion project. Taipei, Taiwan: Taipei Municipal.
Khazaei, J., and A. Eslami. 2016. “Behavior of helical piles–as a geoenvironmental choice–by frustum confining vessel.” Adv. Sci. Technol. Res. J. 10 (31): 8–22. https://doi.org/10.12913/22998624/64113.
Kim, D., K. Baek, and K. Park. 2018. “Analysis of the bearing capacity of helical pile with hexagonal joints.” Materials 11 (10): 1890. https://doi.org/10.3390/ma11101890.
Knappett, J. A., M. J. Brown, A. J. Brennan, and L. Hamilton. 2014. “Optimising the compressive behaviour of screw piles in sand for marine renewable energy applications.” In Vol. IC of Proc., DFI/EFFC 11th Int. Conf. on Piling and Deep Foundations. Stockholm, Sweden: Deep Foundations Institute.
Krasiński, A., and M. Wiszniewski. 2017. “Static load test on instrumented pile – field data and numerical simulations.” Stud. Geotech. Mech. 39 (3): 17–25. https://doi.org/10.1515/sgem-2017-0026.
Lanyi-Bennett, S. A., and L. Deng. 2019. “Effects of inter-helix spacing and short-term soil setup on the behaviour of axially loaded helical piles in cohesive soil.” Soils Found. 59 (2): 337–350. https://doi.org/10.1016/j.sandf.2018.12.002.
Lee, S. H. H. 1990. “Regression models of shear wave velocities in Taipei basin.” J. Chin. Inst. Eng. 13 (5): 519–532. https://doi.org/10.1080/02533839.1990.9677284.
Likins, G., and F. Rausche. 2004. “Correlation of CAPWAP with static load tests.” In Proc., 7th Int. Conf. on the Application of Stress Wave Theory to Piles, 153–165. Selangor, Malaysia: The Institute of Engineers, Malaysia.
Livneh, B., and M. H. El Naggar. 2008. “Axial testing and numerical modeling of square shaft helical piles under compressive and tensile loading.” Can. Geotech. J. 45 (8): 1142–1155. https://doi.org/10.1139/T08-044.
Long, J. H., J. Hendrix, and D. Jaromin. 2009. “Comparison of five different methods for determining pile bearing capacities.” Wisconsin Highway Research Program. minds.wisconsin.edu/handle/1793/53923.
Lutenegger, A. J. 2009. “Cylindrical shear or plate bearing? — Uplift behavior of multi-helix screw anchors in clay.” Contemporary Topics in Deep Foundations, Geotechnical Special Publication 185, edited by M. Iskander, D. F. Laefer, and M. H. Hussein, 456–463. Reston, VA: ASCE.
Mabsout, M. E., and J. L. Tassoulas. 1994. “A finite element model for the simulation of pile driving.” Int. J. Numer. Methods Eng. 37 (2): 257–278. https://doi.org/10.1002/nme.1620370206.
Mahutka, K. P., F. König, and J. Grabe. 2006. “Numerical modelling of pile jacking, driving and vibratory driving.” In Proc., Int. Conf. on Numerical Simulation of Construction Processes in Geotechnical Engineering for Urban Environment, edited by T. Triantafyllidis, 235–246. Rotterdam, Netherlands: AA Balkema.
Middendorp, P. 2000. “Keynote lecture: Statnamic the engineering of art.” In Proc., 6th Int. Conf. on the Application of Stress Wave Theory to Piles, edited by S. Niyama and J. Beim, 551–562. Rotterdam, Netherlands: Taylor & Francis Group / A.A. Balkema.
Mohajerani, A., D. Bosnjak, and D. Bromwich. 2016. “Analysis and design methods of screw piles: A review.” Soils Found. 56 (1): 115–128. https://doi.org/10.1016/j.sandf.2016.01.009.
Motamedinia, H., N. Hataf, and G. Habibagahi. 2019. “A study on failure surface of helical anchors in sand by PIV/DIC technique.” Int. J. Civ. Eng. 17 (12): 1813–1827. https://doi.org/10.1007/s40999-018-0380-2.
Nabizadeh, F., and A. J. Choobbasti. 2017. “Field study of capacity helical piles in sand and silty clay.” Transp. Infrastruct. Geotechnol. 4 (1): 3–17. https://doi.org/10.1007/s40515-016-0036-0.
Nath, B. 1990. “A continuum method of pile driving analysis: Comparison with the wave equation method.” Comput. Geotech. 10 (4): 265–285. https://doi.org/10.1016/0266-352X(90)90018-Q.
Naveen, B. P., C. R. Parthasarathy, and T. G. Sitharam. 2014. “Numerical modeling of pile load test.” In Proc., 4th China Int. Piling and Deep Foundations Summit, 156–161. Shanghai, China: Shanghai Fangxun Construction Consulting Co., Ltd.
Obrzud, R., and A. Truty. 2018. The hardening soil model-a practical guidebook. Software engineering. Z_Soil.PC 100701. Lausanne, Switzerland: Zace Services.
Ohba, S., and I. Toriuma. 1970. “Research on vibrational characteristics of soil deposits in Osaka, part 2, on velocities of wave propagation and predominant periods of soil deposits.” Summaries of Technical Papers of Annual Meeting. [In Japanese.] Tokyo: Architectural Institute of Japan.
Papadopoulos, B. P. 1992. “Settlements of Shallow Foundations on cohesionless soils.” J. Geotech. Eng. 118 (3): 377–393. https://doi.org/10.1061/(ASCE)0733-9410(1992)118:3(377).
Perko, H. A. 2009. Helical piles: A practical guide to design and installation. New York: John Wiley & Sons.
Perko, H. A. 2000. “Energy method for predicting installation torque of helical foundations and anchors.” In New technological and design developments in deep foundations, Geotechnical Special Publication 100, edited by N. D. Dennis, R. Castelli, and M. W. O'Neil, 342–352. Reston, VA: ASCE.
Plaxis 2D. 2019. Reference manual. Advancing Infrastructure. Delft, Netherlands: Bentley Systems.
Rajagopal, C., C. H. Solanki, and Y. K. Tandel. 2012. “Comparison of static and dynamic load test of pile.” Electron. J. Geotech. Eng. 17: 1905–1914.
Rao, S. N., Y. V. S. N. Prasad, and M. D. Shetty. 1991. “The behaviour of model screw piles in cohesive soils.” Soils Found. 31 (2): 35–50. https://doi.org/10.3208/sandf1972.31.2_35.
Rao, S. N., Y. V. S. N. Prasad, and C. Veeresh. 1993. “Behaviour of embedded model screw anchors in soft clays.” Géotechnique 43 (4): 605–614. https://doi.org/10.1680/geot.1993.43.4.605.
Sakr, M. 2009. “Performance of helical piles in oil sand.” Can. Geotech. J. 46 (9): 1046–1061. https://doi.org/10.1139/T09-044.
Sakr, M. 2010. “High capacity helical piles–a new dimension for bridge foundations.” In Proc., 8th Int. Conf. on Short and Medium Span Bridges, 142-1–142-11. Niagara Falls, Canada: Canadian Society for Civil Engineering.
Sakr, M. 2011. “Installation and performance characteristics of high capacity helical piles in cohesionless soils.” DFI J. 5 (1): 39–57. https://doi.org/10.1179/dfi.2011.004.
Sakr, M. 2013. “Comparison between high strain dynamic and static load tests of helical piles in cohesive soils.” Soil Dyn. Earthquake Eng. 54: 20–30. https://doi.org/10.1016/j.soildyn.2013.07.010.
Salhi, L., O. Nait-Rabah, C. Deyrat, and C. Roos. 2013. “Numerical modeling of single helical pile behavior under compressive loading in sand.” Electron. J. Geotech. Eng. 18: 4319–4338.
Schmertmann, J. H. 1970. “Static cone to compute static settlement over sand.” J. Soil Mech. Found. Div. 96: 1011–1043. https://doi.org/10.1061/JSFEAQ.0001418.
Soltani-Jigheh, H., and P. Zahedi. 2020. “Load transfer mechanism of screw piles in sandy soils.” Indian Geotech. J. 50: 871–879. https://doi.org/10.1007/s40098-020-00431-5.
Spagnoli, G., and C. D. H. C. Tsuha. 2020. “A review on the behavior of helical piles as a potential offshore foundation system.” Mar. Georesour. Geotechnol. 38 (9): 1013–1036. https://doi.org/10.1080/1064119X.2020.1729905.
Stanier, S. A., J. A. Black, and C. C. Hird. 2014. “Modelling helical screw piles in soft clay and design implications.” Proc. Inst. Civ. Eng. – Geotech. Eng. 167 (5): 447–460. https://doi.org/10.1680/geng.13.00021.
Tappenden, K., D. Sego, and P. Robertson. 2009. “Load transfer behavior of full-scale instrumented screw anchors.” In Contemporary topics in deep foundations, Geotechnical Special Publication 185, edited by M. Iskander, D. F. Laefer, and M. H. Hussein, 472–479. Reston, VA: ASCE.
Tappenden, K. M. 2007. “Predicting the axial capacity of screw piles installed in western Canadian soils.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Univ. of Alberta.
Tappenden, K. M., and D. C. Sego. 2007. “Predicting the axial capacity of screw piles installed in Canadian soils.” In Proc., OttawaGeo2007, the Diamond Jubilee, 60th Canadian Geotechnical Conf. and 8th Joint CGS/IAH-CNC Groundwater Conf., 1608–1615. Ottawa, Canada: OttawaGeo2007 Organizing Committee.
Tsuha, C. D. H. C., J. M. S. M. dos Santos Filho, and T. D. C. Santos. 2016. “Helical piles in unsaturated structured soil: A case study.” Can. Geotech. J. 53 (1): 103–117. https://doi.org/10.1139/cgj-2015-0017.
Vaidya, R. 2006. “Introduction to high strain dynamic pile testing and reliability studies in southern India.” In Proc., Indian Geotechnical Conf., 901–904. Chennai, India: Indian Geotechnical Society.
Webb, D. L. 1970. “Settlement of structures on deep alluvial sandy sediments in Durban, South Africa.” In Proc., Conf. on the In-Situ Behavior of Soils and Rocks, 181–188. London, UK: British Geotechnical Society.
White, B., A. Alzawi, T. Bradka, and Y. Phang. 2013. “High strain dynamic load testing on helical piles–Case study.” In Proc., 1st Int. Geotechnical Symp. on Helical Foundations, 336–346. Univ. of Massachusetts, Amherst: International Society for Helical Foundations.
Zhang, D. J. Y. 1999. “Predicting capacity of helical screw piles in alberta soils.” Master thesis, Dept. of Civil and Environmental Engineering, Univ. of Alberta.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 21 • Issue 6 • June 2021
Copyright
© 2021 American Society of Civil Engineers.
History
Received: May 3, 2020
Accepted: Jan 17, 2021
Published online: Mar 25, 2021
Published in print: Jun 1, 2021
Discussion open until: Aug 25, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.