Centrifuge Model Testing of Loess Landslides Induced by Excavation in Northwest China
Publication: International Journal of Geomechanics
Volume 20, Issue 4
Abstract
Excavation leads to unloading rebound and stress redistribution in the soil of a slope near the excavation face. The process of reequilibrium of the stress is followed by large deformation or even failure of the slope. In this study, the excavation-induced Yangya landslide was selected as a geological prototype. From reduced triaxial compression (RTC) tests, the characteristics of deformation and the mechanical response of unloading soil were analyzed, which were related to the instability and response mechanism of a loess slope under unloading. Furthermore, a geotechnical centrifuge was used to simulate the deformation and failure process under the condition of excavation at the slope toe. The deformation characteristics before and after the slope toe excavation and the response characteristics of the earth pressure inside the slope were studied. The results show that after excavation of the slope toe, local collapse occurs near the excavation surface. The displacement, the potential slip surface, and the tensile cracks of the slope develop progressively from the front edge to the trailing edge of the slope. Moreover, the failure of a loess slope induced by excavation is dependent on the change of pressure unloading ratio; when the confining pressure unloading ratio reaches a critical level, the shear strength decreases sharply. Differences also exist in the critical unloading confining pressure ratio between shallow and deep failures in excavation-induced landslides. Therefore, the scope of the unloading effect of the excavation on the slope directly determines the scale of the landslide. After excavation, stress relaxation clearly occurs within the slope, and the unloading effect is more obvious near the excavation surface. The excavation mainly affects the front and middle parts of the slope and has little or no effect on the rear part of the slope. The deformation and failure mechanisms of the loess slope induced by excavation are characteristic of a typical progressive retreat failure mode landslide.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or codes generated or used during the study are available from the corresponding author by request.
Acknowledgments
This project was partially supported by the National Key R&D Program of China (Grant No. 2017YFC1501002), the Major Program of the National Natural Science Foundation of China (Grant No. 41790445), the National Natural Science Fund for Distinguished Young Scholars of China (Grant No. 41702335), the National Natural Science Foundation of China (Grant No. 41572302), the State Key Laboratory of Geohazard Prevention and Geoenvironment Protection, Chengdu University of Technology (Grant No. SKLGP2017K008), the State Key Laboratory for GeoMechanics and Deep Underground Engineering, China University of Mining and Technology (Grant No. SKLGDUEK1718), and ARC Future Fellowship (Grant No. FT140100019). The first author would like to thank the Chinese Scholarship Council for financial support toward his joint Ph.D. at the University of Newcastle, Australia. We would also like to acknowledge the editors and reviewers for their invaluable comments, leading to a substantial improvement of this manuscript.
References
Arulanandan, K., P. Y. Thompson, B. L. Kutter, N. J. Meegoda, K. K. Muraleetharan, and C. Yogachandran. 1988. “Centrifuge modeling of transport processes for pollutants in soils.” J. Geotech. Eng. 114 (2): 185–205. https://doi.org/10.1061/(ASCE)0733-9410(1988)114:2(185).
ASTM. 2004. Standard test method for consolidated undrained triaxial compression test for cohesive soils. ASTM D4767-95. West Conshohocken, PA: ASTM.
ASTM. 2011. Standard test method for direct shear test of soils under consolidated drained conditions. ASTM D3080/D3080M. West Conshohocken, PA: ASTM.
Birle, E., D. Heyer, and N. Vogt. 2008. “Influence of the initial water content and dry density on the soil–water retention curve and the shrinkage behavior of a compacted clay.” Acta Geotech. 3 (3): 191–200. https://doi.org/10.1007/s11440-008-0059-y.
Bishop, A. W. 1967. “Progressive failure with special reference to the mechanism causing it.” In Proc., Geotechnical Conf. on the Shear Strength of Natural Soils and Rocks, 142–150. Oslo, Norway: Norwegian Geotechnical Institute.
Borja, R. I., and J. A. White. 2010. “Continuum deformation and stability analyses of a steep hillside slope under rainfall infiltration.” Acta Geotech. 5 (1): 1–14. https://doi.org/10.1007/s11440-009-0108-1.
Cao, Z. H., H. L. Liu, G. Q. Kong, and H. Zhou. 2015. “Physical modeling of pipe piles under oblique pullout loads using transparent soil and particle image velocimetry.” J. Cent. South Univ. 22 (11): 4329–4336. https://doi.org/10.1007/s11771-015-2981-0.
Chen, R. P., Z. C. Li, Y. M. Chen, C. Y. Ou, Q. Hu, and M. Rao. 2015. “Failure investigation at a collapsed deep excavation in very sensitive organic soft clay.” J. Perform. Constr. Facil. 29 (3): 04014078. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000557.
Cui, S. H., X. J. Pei, H. Y. Wu, and R. Q. Huang. 2018. “Centrifuge model test of an irrigation-induced loess landslide in the Heifangtai loess platform, Northwest China.” J. Mt. Sci. 15 (1): 130–143. https://doi.org/10.1007/s11629-017-4490-0.
Dell’Avanzi, E., J. G. Zornberg, and A. Cabral. 2004. “Suction profiles and scale factors for unsaturated flow under increased gravitational field.” Soils Found. 44 (3): 1–11. https://doi.org/10.3208/sandf.44.3_79.
Fan, Z. J., P. H. S. W. Kulatilake, J. B. Peng, W. Y. Che, Y. Z. Li, and Z. J. Meng. 2016. “In-flight excavation of a loess slope in a centrifuge model test.” Geotech. Geol. Eng. 34 (5): 1577–1591. https://doi.org/10.1007/s10706-016-0067-x.
Garakani, A. A., S. M. Haeri, A. Khosravi, and G. Habibagahi. 2015. “Hydro-mechanical behavior of undisturbed loessial soil under different stress state conditions.” Eng. Geol. 195 (Sep): 28–41. https://doi.org/10.1016/j.enggeo.2015.05.026.
Haeri, S. M., A. Khosravi, A. A. Garakani, and S. Ghazizadeh. 2017. “Effect of soil structure and disturbance on hydromechanical behavior of collapsible loessial soils.” Int. J. Geomech. 17 (1): 04016021. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000656.
Huang, R. Q., X. J. Pei, X. M. Fan, W. F. Zhang, S. G. Li, and B. L. Li. 2012. “The characteristics and failure mechanism of the largest landslide triggered by the Wenchuan earthquake, May 12, 2008, China.” Landslides 9 (1): 131–142. https://doi.org/10.1007/s10346-011-0276-6.
Jefferson, C., J. S. Smith, M. C. R. Davies, and B. Rea. 2008. “An investigation of periglacial slope stability in relation to soil properties based on physical modelling in the geotechnical centrifuge.” Geomorphology 93 (3–4): 437–459. https://doi.org/10.1016/j.geomorph.2007.03.009.
Jiang, M. J., H. J. Hu, J. B. Peng, and S. Leroueil. 2011. “Experimental study of two saturated natural soils and their saturated remoulded soils under three consolidated undrained stress paths.” Front. Archit. Civ. Eng. China 5 (2): 225–238. https://doi.org/10.1007/s11709-011-0108-8.
Jiang, Y., W. Chen, G. Wang, G. Sun, and F. Zhang. 2017. “Influence of initial dry density and water content on the soil-water characteristic curve and suction stress of a reconstituted loess soil.” Bull. Eng. Geol. Environ. 76 (3): 1085–1095. https://doi.org/10.1007/s10064-016-0899-x.
Keramati, M., N. Shariatmadari, M. Karimpour-Fard, and M. R. N. Shahrbabak. 2016. “Dynamic behaviour of MSW materials under cyclic triaxial testing: A case of Kahrizak landfill, Tehran, Iran.” Iran. J. Sci. Technol. Trans. Civ. Eng. 40 (2): 75–83. https://doi.org/10.1007/s40996-016-0006-3.
Lambe, W. T. 1967. “Stress path method.” J. Soil Mech. Found. Div. 93 (6): 309–331.
Lee, Y. S., C. Y. Cheuk, and M. D. Boltonbolton. 2008. “Instability caused by a seepage impediment in layered fill slopes.” Can. Geotech. J. 45 (10): 1410–1425. https://doi.org/10.1139/T08-067.
Leroueil, S. 2001. “Natural slopes and cuts: Movement and failure mechanisms.” Géotechnique 51 (3): 197–243. https://doi.org/10.1680/geot.2001.51.3.197.
Li, M., G. Zhang, J. M. Zhang, and C. F. Lee. 2011. “Centrifuge model tests on a cohesive soil slope under excavation conditions.” Soils Found. 51 (5): 801–812. https://doi.org/10.3208/sandf.51.801.
Ling, H., and H. I. Ling. 2012. “Centrifuge model simulations of rainfall-induced slope instability.” J. Geotech. Geoenviron. Eng. 138 (9): 1151–1157. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000679.
Ling, H. I., M.-H. Wu, D. Leshchinsky, and B. Leshchinsky. 2009. “Centrifuge modeling of slope instability.” J. Geotech. Geoenviron. Eng. 135 (6): 758–767. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000024.
Liu, D. S. 1985. Loess and the environment, 1–481. [In Chinese.] Beijing: China Ocean Press.
Mahmood, N. S. 2018. “The intrinsic properties of reconstituted soils.” Ph.D. dissertation, Dept. of Civil Engineering, Univ. of Arkansas.
Maiorano, R. M. S., G. Russo, and C. Viggiani. 2014. “A landslide in stiff, intact clay.” Acta Geotech. 9 (5): 817–829. https://doi.org/10.1007/s11440-013-0249-0.
Milne, F. D., M. J. Brown, J. A. Knappett, and M. C. R. Davies. 2012. “Centrifuge modelling of hillslope debris flow initiation.” Catena 92 (May): 162–171. https://doi.org/10.1016/j.catena.2011.12.001.
Mirshekari, M., M. Ghayoomi, and A. Borghei. 2018. “A review on soil-water retention scaling in centrifuge modeling of unsaturated sands.” Geotech. Test. J. 41 (6): 979–997. https://doi.org/10.1520/GTJ20170120.
Ng, C. W. W. 1999. “Stress paths in relation to deep excavations.” J. Geotech. Geoenviron. Eng. 125 (5): 357–363. https://doi.org/10.1061/(ASCE)1090-0241(1999)125:5(357).
Ng, C. W. W., K. Viroon, and A. Leung. 2016. “Centrifuge modelling of the effects of root geometry on transpiration-induced suction and stability of vegetated slopes.” Landslides 13 (5): 925–938. https://doi.org/10.1007/s10346-015-0645-7.
Panet, M., and A. Guenot. 1982. “Analysis of convergence behind the face of a tunnel.” In Proc., 3rd Int. Symp. on Tunneling’82, 197–204. London: Institution of Mining and Metallurgy.
Pei, X. J., F. Y. Zhang, W. J. Wu, and S. Y. Liang. 2015. “Physicochemical and index properties of loess stabilized with lime and fly ash piles.” Appl. Clay Sci. 114 (Sep): 77–84. https://doi.org/10.1016/j.clay.2015.05.007.
Pei, X. J., X. C. Zhang, B. Guo, G. H. Wang, and F. Y. Zhang. 2017. “Experimental case study of seismically induced loess liquefaction and landslide.” Eng. Geol. 223 (Jun): 23–30. https://doi.org/10.1016/j.enggeo.2017.03.016.
Professional Standard of China. 1999. Specification of soil test. SL237. [In Chinese.] Beijing: China Water & Power Press.
Professional Standard of China. 2008. Standard for engineering classification of soil. [In Chinese.] GB/T 50145-2007. Beijing: China Planning Press.
Richard, G., I. Cousin, J. F. Sillon, A. Bruand, and J. Guérif. 2001. “Effect of compaction on the porosity of a silty soil: Influence on unsaturated hydraulic properties.” Eur. J. Soil Sci. 52 (1): 49–58. https://doi.org/10.1046/j.1365-2389.2001.00357.x.
Rogers, C. D. F., T. A. Dijkstra, and I. J. Smalley. 1994. “Hydro consolidation and subsidence of loess: Studies from China, Russia, North America and Europe: In memory of Jan Sajgalik.” Eng. Geol. 37 (2): 83–113. https://doi.org/10.1016/0013-7952(94)90045-0.
Schofield, A. N. 1980. “Cambridge geotechnical centrifuge operations.” Geotechnique 30 (3): 227–268. https://doi.org/10.1680/geot.1980.30.3.227.
Takemura, J., M. Kondoh, T. Esaki, M. Kouda, and O. Kusakabe. 1999. “Centrifuge model tests on double propped wall excavation in soft clay.” Soil Found. 39 (3): 75–87. https://doi.org/10.3208/sandf.39.3_75.
Tamrakar, S. B., Y. Toyosawa, K. Itoh, and S. Timpong. 2006. “Failure heights comparison during excavation using in-flight excavator.” In Physical modelling in geotechnics, edited by C. W. W. Ng, L. M. Zhang, and Y. H. Wang, 385–390. London: Taylor & Francis.
Tan, Y., and B. Wei. 2011. “Performance of an overexcavated metro station and facilities nearby.” J. Perform. Constr. Facil. 26 (3): 241–254. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000231.
Tang, H., Z. Duan, D. P. Wang, and Q. Dang. 2020. “Experimental investigation of creep behavior of loess under different moisture contents.” Bull. Eng. Geol. Environ. 79 (1): 411–422. https://doi.org/10.1007/s10064-019-01545-8.
Toyosawa, Y., N. Horii, S. Tarnate, and N. Suemasa. 1996. “Failure characteristics of a sheet pile wall in centrifuge tests.” In Proc., Int. Symp. on Geotechnical Aspects of Underground Construction in Soft Ground, edited by E. R. J. Mair and R. N. Taylor, 225–230. London: Taylor & Francis.
Tu, X. B., A. K. L. Kwong, F. C. Dai, L. G. Tham, and H. Min. 2009. “Field monitoring of rainfall infiltration in a loess slope and analysis of failure mechanism of rainfall-induced landslides.” Eng. Geol. 105 (1–2): 134–150. https://doi.org/10.1016/j.enggeo.2008.11.011.
Vanapalli, S. K., D. G. Fredlund, and D. E. Pufahl. 1999. “The influence of soil structure and stress history on the soil-water characteristics of a compacted till.” Géotechnique 49 (2): 143–159. https://doi.org/10.1680/geot.1999.49.2.143.
Viswanadham, B. V. S., and S. Rajesh. 2009. “Centrifuge model tests on clay based engineered barriers subjected to differential settlements.” Appl. Clay Sci. 42 (3–4): 460–472. https://doi.org/10.1016/j.clay.2008.06.002.
Wang, G. 1992. “Relationship between the origin of loess landslides and the human activities in China.” In Landslides, Vol. 1 of Proc., 6th Int. Symp. on Landslides, 263–268. Rotterdam, Netherlands: A.A. Balkema.
Wang, J. D., S. F. Xiao, and Z. Y. Zhang. 2001. “The mechanism for movement of irrigation–induced high-speed loess landslide.” [In Chinese.] J. Eng. Geol. 9 (3): 241–246.
Wang, J. J., Y. Liang, H. P. Zhang, Y. Wu, and X. Lin. 2014. “A loess landslide induced by excavation and rainfall.” Landslides 11 (1): 141–152. https://doi.org/10.1007/s10346-013-0418-0.
Wang, L. M., Z. X. Yuan, H. M. Sun, and J. Deng. 2010. “Criterions, prediction and prevention of loess liquefaction.” In Proc., 5th Int. Conf. on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics. Rolla, MO: Missouri Univ. of Science and Technology.
Xu, L., M. R. Coop, M. S. Zhang, and G. L. Wang. 2018. “The mechanics of a saturated silty loess and implications for landslides.” Eng. Geol. 236 (Mar): 29–42. https://doi.org/10.1016/j.enggeo.2017.02.021.
Xu, M., E. Song, and J. Chen. 2012. “A large triaxial investigation of the stress-path-dependent behavior of compacted rockfill.” Acta Geotech. 7 (3): 167–175. https://doi.org/10.1007/s11440-012-0160-0.
Xue, J. F., and K. Gavin. 2008. “Effect of rainfall intensity on infiltration into partly saturated slopes.” Geotech. Geol. Eng. 26 (2): 199–209. https://doi.org/10.1007/s10706-007-9157-0.
Xue, J.-F., and K. Gavin. 2007. “Simultaneous determination of critical slip surface and reliability index for slopes.” J. Geotech. Geoenviron. Eng. 137 (7): 878–886. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:7(878).
Yuan, Z. X., and L. M. Wang. 2009. “Collapsibility and seismic settlement of loess.” Eng. Geol. 105 (1–2): 119–123. https://doi.org/10.1016/j.enggeo.2008.12.002.
Zhang, D. X., and G. H. Wang. 2007. “Study of the 1920 Haiyuan earthquake-induced landslides in loess (China).” Eng. Geol. 94 (1–2): 76–88. https://doi.org/10.1016/j.enggeo.2007.07.007.
Zhang, F. Y., and G. H. Wang. 2018. “Effect of irrigation-induced densification on the post-failure behavior of loess flowslides occurring on the Heifangtai area, Gansu, China.” Eng. Geol. 236 (Mar): 111–118. https://doi.org/10.1016/j.enggeo.2017.07.010.
Zhang, G., Y. Hu, and L. P. Wang. 2015. “Behaviour and mechanism of failure process of soil slopes.” Environ. Earth Sci. 73 (4): 1701–1713. https://doi.org/10.1007/s12665-014-3522-0.
Zhang, S., X. J. Pei, S. Y. Wang, R. Q. Huang, X. C. Zhang, and Z. L. Chang. 2019a. “Centrifuge model testing of a loess landslide induced by rising groundwater in Northwest China.” Eng. Geol. 259 (Sep): 105170. https://doi.org/10.1016/j.enggeo.2019.105170.
Zhang, S., X. C. Zhang, X. J. Pei, S. Y. Wang, R. Q. Huang, Q. Xu, and Z. L. Wang. 2019b. “Model test study on the hydrological mechanisms and early warning thresholds for loess fill slope failure induced by rainfall.” Eng. Geol. 258 (Aug): 105135. https://doi.org/10.1016/j.enggeo.2019.05.012.
Zhao, Y., G. Zhang, D. Hu, and Y. Han. 2018. “Centrifuge model test study on failure behavior of soil slopes overlying the bedrock.” Int. J. Geomech. 18 (11): 04018144. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001292.
Zhuang, J. Q., and J. B. Peng. 2014. “A coupled slope cutting—A prolonged rainfall-induced loess landslide: A 17 October 2011 case study.” Bull. Eng. Geol. Environ. 73 (4): 997–1011. https://doi.org/10.1007/s10064-014-0645-1.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 20 • Issue 4 • April 2020
Copyright
©2020 American Society of Civil Engineers.
History
Received: Dec 30, 2018
Accepted: Sep 3, 2019
Published online: Jan 30, 2020
Published in print: Apr 1, 2020
Discussion open until: Jun 30, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.