Numerical Analysis for a Realistic Support Design: Case Study of the Komurhan Tunnel in Eastern Turkey
Publication: International Journal of Geomechanics
Volume 16, Issue 3
Abstract
The aim of this study was to highlight the importance of the numerical approach in realistic support design for tunneling. The Komurhan Tunnel, which is to be constructed between the Elazig–Malatya highway, located east of Elazig City in eastern Turkey, was selected as the application site of this study. The lithology of this area consists of Late Cretaceous–age ophiolitic rocks, known as Komurhan ophiolites. Field and laboratory studies were performed to determine the geotechnical properties of rock mass and intact rock materials. Empirical and numerical approaches were used, and the results were compared, focusing on tunnel design safety. The rock mass was classified in terms of the rock mass rating (RMR), rock mass index (RMi), Austrian tunneling method, and geological strength index rock mass classification systems, and then the support systems for the tunnel were determined accordingly. The support systems obtained from the classification systems were also analyzed using software based on the FEM. On the basis of the numerical analysis, a more reliable and safe support design was recommended. The results show that the support systems suggested by the RMi method were not sufficient for the walls; however, the support systems were found to be safe for the crowns. Furthermore, the support systems suggested by the RMR system did not provide enough stability for both walls and crowns. The support system recommended in this study reduced the thickness of the plastic zone and total displacement values.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge the financial support provided by the Firat University Scientific Research Projects Unit of Turkey (Project No. MF.12.23).
References
ASTM. (2000). “Standard test method for pressuremeter testing in soils: Annual book of ASTM standards.” D4719-07, West Conshohocken, PA.
Austrian Standards. (1994). “Untertagebauarbeiten Werkvertragsnorm.” ÖNORM B2203, Vienna, Austria (in German).
Baguelin, F., Jezequel, J. F., and Shields, D. H. (1978). The pressuremeter and foundation engineering, Trans Tech Publications, Clausthal, Germany.
Barton, N. (2002). “Some new Q-value correlations to assist in site characterisation and tunnel design.” Int. J. Rock Mech. Min. Sci., 39(2), 185–216.
Beyarslan, M. (1996). “Komurhan ofiyolit biriminin petrografik ve petrolojik incelenmesi.” Doktora Tezi, Fırat Universitesi Fen Bilimleri Enstitüsü, Elazığ, Turkey (in Turkish).
Beyarslan, M., and Bingöl, A. F. (2001). “Origin of Wehrlitic intrusions in the İspendere (Malatya) and Komurhan (Elazig) ophiolitic complex (Eastern Taurus–Turkey).” Geosound, 38, 39–47.
Bieniawski, Z. T. (1974). “Geomechanics classification of rock masses and its application in tunnelling.” Proc., 3rd Int. Congress on Rock Mechanics, Vol. 11A, International Society for Rock Mechanics, Lisbon, Portugal, 27–32.
Bieniawski, Z. T. (1978). “Determining rock mass deformability: Experience from case histories.” Int. J. Rock. Mech. Min. Sci. Geomech. Abstr., 15(5), 237–247.
Bieniawski, Z. T. (1989). Engineering rock mass classifications, John Wiley & Sons, New York, 237.
Bowles, J. E. (1988). Foundation analysis and design, McGraw-Hill Book Co., New York.
Chun, B.-S, Lee, Y.-J, Seo, D.-D., and Lim, B.-S. (2006). “Correlation deformation modulus by PMT with RMR and rock mass condition.” Tunnelling Underground Space Technol., 21(3–4), 231–232.
Cividini, A., Contini, A., Locatelli, L., and Gioda, G. (2012). “Investigation on the cause of damages of a deep tunnel.” Int. J. Geomech., 722–731.
Deere, D. U. (1964). “Technical description of rock cores for engineering purposed.” Rock Mech. Rock Eng., 1, 17–22.
Dips [Computer software]. Version 5.1. Rocscience, Toronto.
Franzius, J. N., and Potts, D. M. (2005). “Influence of mesh geometry on three-dimensional finite-element analysis of tunnel excavation.” Int. J. Geomech., 256–266.
Galera, J. M., Alvarez, M., and Bieniawski, Z. T. (2005). “Evaluation of the deformation modulus of rock masses: Comparison of pressuremeter and dilatometer tests with RMR prediction.” Proc., ISP5-PRESSIO, Paris, 1–25.
Genis, M., Basarir, H., Ozarslan, A., Bilir, E., and Balaban, E. (2007). “Engineering geological appraisal of the rock masses and preliminary support design, Dorukhan Tunnel, Zonguldak, Turkey.” Eng. Geol., 92(1–2), 14–26.
Gurocak, Z. (2011). “Analyses of stability and support design for a diversion tunnel at the Kapikaya dam site, Turkey.” Bull. Eng. Geol. Environ., 70(1), 41–52.
Gurocak, Z., Solanki, P., and Zaman, M. M. (2007). “Empirical and numerical analyses of support requirements for a diversion tunnel at the Boztepe dam site, eastern Turkey.” Eng. Geol., 91(2–4), 194–208.
Hoek, E., and Brown, E. T. (1997). “Practical estimates of rock mass strength.” Int. J. Rock Mech. Min. Sci., 34(8), 1165–1186.
Hoek, E., Carranza-Torres, C., and Corkum, B. (2002). “Hoek-Brown failure criterion—2002 edition.” Proc., 5th North American Rock Mechanics Symp., Vol. 1, Toronto, 267–273.
Hoek, E., and Diederichs, M. S. (2006). “Empirical estimation of rock mass modulus.” Int. J. Rock Mech. Min. Sci., 43(2), 203–215.
Hoek, E., Kaiser, P. K., and Bawden, W. F. (1995). Support of underground excavations in hard rock, Balkema, Netherlands, Rotterdam.
Huang, X., Schweiger, H. F., and Huang, H. (2013). “Influence of deep excavations on nearby existing tunnels.” Int. J. Geomech, 170–180.
ISRM (International Society for Rock Mechanics). (1981). Rock characterization, testing and monitoring, ISRM suggested methods, Pergamon Press, Oxford, U.K., 211.
ISRM (International Society for Rock Mechanics). (2007). The complete ISRM suggested methods for rock characterization, testing and monitoring: 1974-2006. ISRM Turkish National Group, Ankara, Turkey, 628.
Jade, S., and Sitharam, T. G. (2003). “Characterization of strength and deformation of jointed rock mass based on statistical analysis.” Int. J. Geomech., 43–54.
Kaya, A., and Bulut, F. (2013). “Stability analyses of tunnels excavated in weak rock masses using empirical and numerical methods.” J. Geol. Eng., 37(2), 103–116.
Kaya, A., Bulut, F., Alemdag, S., and Sayin, A. (2011). “Analysis of support requirements for a tunnel portal in weak rock: A case study in Turkey.” Sci. Res. Essays, 6(31), 6566–6583.
KGM (Turkish General Directorate of Highways). (1997). List of specifications of the underground tunnel excavations with NATM practice. Turkish Ministry of Public Works, Ankara, Turkey (in Turkish).
KGM (Turkish General Directorate of Highways). (2012). The geological and geotechnical report of Elazig-Malatya Highway Komurhan Tunnel and access roads. 8th Regional Directorate, Elazig, Turkey.
Marinos, P., and Hoek, E. (2000). “GSI: A geologically friendly tool for rock mass strength estimation.” Int. Proc. of the GeoEng2000 at the Int. Conf. on Geotechnical and Geological Engineering, Technomics, Lancaster, PA, 1422–1446.
Marinos, P., and Hoek, E. (2001). “Estimating the geotechnical properties of heterogeneous rock masses such as flysch.” Bull. Eng. Geol. Environ., 60(2), 85–92.
Ménard, L. (1956). “An apparatus for measuring the strength of soils in place.” M.S. thesis, Univ. of Illinois, Champaign, IL.
Ménard, L. (1975). “Interpretation and application of pressuremeter test results to foundation design.” Sols Soils, No. 26.
Palmström, A. (1982). The volumetric joint count: A useful and simple measure of the degree of rock mass jointing, IAEG Congress, New Delhi, India, 221–228.
Palmström, A. (1995). “RMi—A rock mass characterization system for rock engineering purposes.” Ph.D. thesis, Univ. of Oslo, Oslo, Norway.
Palmström, A. (2000). “Recent developments in rock support estimates by the RMi.” J. Rock Mech. Tunnelling Technol., 6(1), 1–19.
Ramamurthy, T. (2004). “A geo-engineering classification for rocks and rock masses.” Int. J. Rock Mech. Min. Sci., 41(1), 89–101.
Rizaoglu, T., Parlak, O., and Isler, F. (2004). “Geochemistry and tectonic setting of the Kömürhan Ophiolite in Southeast Anatolia.” Proc., 5th Int. Eastern Mediterranean Geology Symp., Thessaloniki, Greece.
Phase2 [Computer software]. Version 7.0. Rocscience, Toronto.
Sheorey, P. R., Murali Mohan, G., and Sinha, A. (2001). “Influence of elastic constants on the horizontal in situ stress.” Int. J. Rock Mech. Min. Sci., 38(8), 1211–1216.
Surjadinata, J., Hull, T., Carter, J., and Poulos, H. (2006). “Combined finite- and boundary-element analysis of the effects of tunneling on single piles.” Int. J. Geomech., 374–377.
Turkish Ministry of Public Works and Settlement. (1996). Evaluation of earthquake regions by geographical information systems, Turkish Ministry of Public Works and Settlement, Ankara, Turkey.
Yalcin, E. (2013). “Empirical and numerical analyses of support designs for Komurhan Tunnel (Elazig).” M.S. thesis, Firat Univ., Elazig, Turkey.
Yazgan, E. (1984). “Geodynamic evolution of the eastern Taurus region (Malatya-Elazig area, Turkey).” Proc., Int. Symp. on Geology of Taurus Belt, MTA, Ankara, Turkey, 199–208.
Information & Authors
Information
Published In
International Journal of Geomechanics
Volume 16 • Issue 3 • June 2016
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jan 12, 2015
Accepted: Jun 22, 2015
Published online: Dec 30, 2015
Discussion open until: May 30, 2016
Published in print: Jun 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.