Abstract
In vibration-based damage identification, a common problem is that modal information is not enough and insensitive to local damage. To solve this problem, an effective method is to increase the amount of modal information and enhance the sensitivity of the experimental data to the local damage. In this paper, a damage identification method based on additional virtual masses and Bayesian theory is proposed. First, the virtual structure with optimal additional mass and high sensitivity to local damage is determined through sensitivity analysis, and then a large number of virtual structures can be obtained by adding virtual masses; thus, a lot of modal and statistical information of virtual structures can be obtained. Second, the Bayesian theory is used to obtain the posterior probability distribution of the damage factor when structural a priori information is considered. Third, by finding the extreme value of the probability density function, the damage factor is derived based on the a priori information and the statistical information of virtual structures. Finally, the effectiveness of the proposed method is verified by numerical simulations and experiments of a 3-story frame structure. Experimental and numerical results show that the proposed method can be used to identify the damage severity of each substructure and thus damaged substructures can be localized and quantified; the error in damage factor is basically within 5%, which shows the accuracy of the proposed method. The proposed method can not only provide the structural damage localization and quantification result (i.e., the damage factor), but also the probability distribution of the damage factor; moreover, it has high sensitivity to damage and high accuracy and efficiency.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to express their gratitude for financial support from the National Natural Science Foundation of China (51508070 and 51778106), the National Key Basic Research Program of China (2015CB060000), the Fundamental Research Funds for the Central Universities (DUT16LK10 and DUT16YQ101), the Opening Fund of State Key Laboratory of Structural Analysis for Industrial Equipment (GZ1601), the Foundation of Key Laboratory of Structures Dynamic Behavior and Control (Ministry of Education) in Harbin Institute of Technology, and the project DEC-2014/15/B/ST8/04363 of the National Science Centre, Poland.
References
An, Y. H., D. L. Guan, Y. L. Ding, and J. P. Ou. 2017. “Fast warning method for rigid hangers in a high-speed railway arch bridge using long-term monitoring data.” J. Perform. Constr. Facil. 31 (6): 04017103. https://doi.org/10.1061/(ASCE)CF.1943-5509.0001097.
Beck, J. L., and L. S. Katafygiotis. 1998. “Updating models and their uncertainties. I: Bayesian statistical framework.” J. Eng. Mech. 124 (4): 455–461. https://doi.org/10.1061/(ASCE)0733-9399(1998)124:4(455).
Błachowski, B., Y. H. An, B. F. Spencer Jr., and J. P., Ou. 2017. “Axial strain accelerations approach for damage localization in statically determinate truss structures.” Comput.-Aided Civ. Infrastruct. Eng. 32 (4): 304–318. https://doi.org/10.1111/mice.12258.
Cha, P. D., and L. G. de Pillis. 2001. “Model updating by adding known masses.” Int. J. Numer. Methods Eng. 50 (11): 2547–2571. https://doi.org/10.1002/nme.136.
Chen, Z. D. 2015. Modal updating method and experimental study using additional virtual masses. [In Chinese.] Dalian, China: Dalian Univ. of Technology.
Dems, K., and Z. Mróz. 2010. “Damage identification using modal, static and thermographic analysis with additional control parameters.” Comput. Struct. 88 (21–22): 1254–1264. https://doi.org/10.1016/j.compstruc.2010.07.005.
Deng, C., S. W. Hu, and P. Y. Gu. 2013. “Modal identification and finite element model updating by adding known masses.” Appl. Mech. Mater. 405: 808–815. https://doi.org/10.4028/www.scientific.net/AMM.405-408.808.
Dinh, H. M., T. Nagayama, and Y. Fujino. 2012. “Structural parameter identification by use of additional known masses and its experimental application.” Struct. Control Health Monit. 19 (3): 436–450. https://doi.org/10.1002/stc.444.
Fan, W., and P. Z. Qiao. 2011. “Vibration-based damage identification methods: A review and comparative study.” Struct. Health Monit. 10 (1): 83–111. https://doi.org/10.1177/1475921710365419.
Gong, M. S., X. H. Li, Y. B. Gao, and Q. F. Liu. 2014. “Study on probabilistic identification method of structural physical parameter based on Bayesian estimation.” Appl. Mech. Mater. 578: 1113–1117. https://doi.org/10.4028/www.scientific.net/AMM.578-579.1113.
Hou, J. L., Ł. Jankowski, and J. P. Ou. 2013. “Structural damage identification by adding virtual masses.” Struct. Multidiscip. Optim. 48 (1): 59–72. https://doi.org/10.1007/s00158-012-0879-0.
Hou, J. L., Ł. Jankowski, and J. P. Ou. 2014. “Substructure isolation and damage identification using free responses.” Sci. China Technol. Sci. 57 (9): 1698–1706. https://doi.org/10.1007/s11431-014-5622-1.
Katafygiotis, L. S., and J. L. Beck. 1998. “Updating models and their uncertainties. II: Model identifiability.” J. Eng. Mech. 124 (4): 463–467. https://doi.org/10.1061/(ASCE)0733-9399(1998)124:4(463).
Kołakowski, P., M. Wikło, and J. Holnicki-Szulc. 2008. “The virtual distortion method—A versatile reanalysis tool for structures and systems.” Struct. Multidiscip. Optim. 36 (3): 217–234. https://doi.org/10.1007/s00158-007-0158-7.
Kuok, S. C., and K. V. Yuen. 2012. “Structural health monitoring of canton tower using Bayesian framework.” Smart Struct. Syst. 10 (4–5): 375–391. https://doi.org/10.12989/sss.2012.10.4_5.375.
Kuok, S. C., and K. V. Yuen. 2016. “Investigation of modal identification and modal identifiability of a cable-stayed bridge with Bayesian framework.” Smart Struct. Syst. 17 (3): 445–470. https://doi.org/10.12989/sss.2016.17.3.445.
Li, D. S., D. Lu, and J. L. Hou. 2017. “Pipeline damage identification based on additional virtual masses.” Appl. Sci. 7 (10): 1040. https://doi.org/10.3390/app7101040.
Nalitolela, N. G., J. E. T. Penny, and M. I. Friswell. 1992. “A mass or stiffness addition technique for structural parameter updating.” Int. J. Anal. Exp. Modal Anal. 7 (3): 157–168.
Nalitolela, N. G., J. E. T. Penny, and M. I. Friswell. 1993. “Updating model parameters by adding an imagined stiffness to the structure.” Mech. Syst. Signal Process. 7 (2): 161–172. https://doi.org/10.1006/mssp.1993.1005.
Simoen, E., B. Moaveni, J. P. Conte, and G. Lombaert. 2013. “Uncertainty quantification in the assessment of progressive damage in a 7-story full-scale building slice.” J. Eng. Mech. 139 (12): 1818–1830. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000610.
Vanik, M. W., J. L. Beck, and S. K. Au. 2000. “Bayesian probabilistic approach to structural health monitoring.” J. Eng. Mech. 126 (7): 738–745. https://doi.org/10.1061/(ASCE)0733-9399(2000)126:7(738).
Yuen, K. V., S. K. Au, and J. L. Beck. 2004. “Two-stage structural health monitoring approach for Phase I benchmark studies.” J. Eng. Mech. 130 (1): 16–33. https://doi.org/10.1061/(ASCE)0733-9399(2004)130:1(16).
Yuen, K. V., J. L. Beck, and L. S. Katafygiotis. 2006. “Unified probabilistic approach for model updating and damage detection.” J. Appl. Mech. 73 (4): 555–564. https://doi.org/10.1115/1.2150235.
Yuen, K. V., and S. C. Kuok. 2011. “Bayesian methods for updating dynamic models.” Appl. Mech. Rev. 64 (1): 010802. https://doi.org/10.1115/1.4004479.
Zhang, F. L., H. B. Xiong, W. X. Shi, and X. Ou. 2016. “Structural health monitoring of Shanghai Tower during different stages using a Bayesian approach.” Struct. Control Health Monit. 23 (11): 1366–1384. https://doi.org/10.1002/stc.1840.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Oct 19, 2017
Accepted: May 9, 2018
Published online: Aug 11, 2018
Published in print: Oct 1, 2018
Discussion open until: Jan 11, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.