Seismic Response Analysis of the Planar Rocking Frame
Publication: Journal of Engineering Mechanics
Volume 141, Issue 7
Abstract
Unlike conventional seismic design, the columns of a rocking frame are designed to uplift and pivot during earthquake excitation. This paper investigates, analytically and numerically, the seismic response of a rocking frame with columns unequal in height (asymmetric), which are either freestanding or hybrid, i.e., enhanced with supplemental damping and recentering capacity. The paper establishes the equations of motion following the principles of analytical dynamics. Throughout the study, the deformation of the structural members is considered negligible. The analysis considers both pulse-type and non-pulse-type (historic) ground motions. It shows that the effect of asymmetry on the seismic stability of the rocking frame is marginal compared with the symmetric configuration, despite the very different kinematics of the corresponding rocking mechanisms. In contrast, the seismic stability of the hybrid rocking frame is very sensitive to fracture elongation of the supplemental restoring (tendons) and damping devices. The results confirm the high-performance seismic behavior of the planar rocking frame, thus illustrating its potential as an alternative seismic design paradigm.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support was provided by the Research Grants Council of Hong Kong, under grant reference number ECS 639613. Discussions with Lecturer Matthew DeJong of the University of Cambridge are also gratefully acknowledged.
References
Aaleti, S., and Sritharan, S. (2009). “A simplified analysis method for characterizing unbonded post-tensioned precast wall systems.” Eng. Struct., 31(12), 2966–2975.
Acikgoz, S., and DeJong, M. J. (2014). “The rocking response of large flexible structures to earthquakes.” Bull. Earthquake Eng., 12(2), 875–908.
Antonellis, G., and Panagiotou, M. (2013). “Seismic response of bridges with rocking foundations compared to fixed-base bridges at a near-fault site.” J. Bridge Eng., 04014007.
Brogliato, B., Zhang, H., and Liu, C. (2012). “Analysis of a generalized kinematic impact law for multibody-multicontact systems, with application to the planar rocking block and chains of balls.” Multibody Syst. Dyn., 27(3), 351–382.
Ceccarelli, M. (2007). Distinguished figures in mechanism and machine science: Their contributions and legacies, Springer, Netherlands.
Chatzis, M., and Smyth, A. (2012). “Modeling of the 3D rocking problem.” Int. J. Non Linear Mech., 47(4), 85–98.
Chen, Y. H., Liao, W. H., Lee, C. L., and Wang, Y. P. (2006). “Seismic isolation of viaduct piers by means of a rocking mechanism.” Earthquake Eng. Struct. Dyn., 35(6), 713–736.
Cheng, C.-T. (2008). “Shaking table tests of a self-centering designed bridge substructure.” Eng. Struct., 30(12), 3426–3433.
DeJong, M. J., and Dimitrakopoulos, E. G. (2014). “Dynamically equivalent rocking structures.” Earthquake Eng. Struct. Dyn., 43(10), 1543–1563.
Dimitrakopoulos, E., Kappos, A. J., and Makris, N. (2009). “Dimensional analysis of yielding and pounding structures for records without distinct pulses.” Soil Dyn. Earthquake Eng., 29(7), 1170–1180.
Dimitrakopoulos, E. G., and DeJong, M. J. (2012a). “Overturning of retrofitted rocking structures under pulse-type excitations.” J. Eng. Mech., 963–972.
Dimitrakopoulos, E. G., and DeJong, M. J. (2012b). “Revisiting the rocking block: Closed-form solutions and similarity laws.” Proc. R. Soc. London, Ser. A, 468(2144), 2294–2318.
Dimitrakopoulos, E. G., and DeJong, M. J. (2013). “Seismic overturning of rocking structures with external viscous dampers.” Computational methods in earthquake engineering, Manolis Papadrakakis, Michalis Fragiadakis, and Vagelis Plevris, eds., Springer, Greece, 243–258.
Dimitrakopoulos, E. G., DeJong, M. J., and Giouvanidis, A. I. (2013). “Seismic assessment of rocking bridge bents using an equivalent rocking block.” 2013 World Congress on Advances in Structural Engineering and Mechanics (Session T4I-I), Korea Federation of Science and Technology Societies, International Association of Structural Engineering & Mechanics (IASEM), Korea National Tourism Corporation, Jeju Convention & Visitors Bureau, Jeju, Korea.
Eatherton, M. R., et al. (2014). “Design concepts for controlled rocking of self-centering steel-braced frames.” J. Struct. Eng., 04014082.
ElGawady, M. A., and Sha’lan, A. (2011). “Seismic behavior of self-centering precast segmental bridge bents.” J. Bridge Eng., 328–339.
Fielder, W., Virgin, L., and Plaut, R. (1997). “Experiments and simulation of overturning of an asymmetric rocking block on an oscillating foundation.” Eur. J. Mech. A. Solids, 16(5), 905–923.
Freudenstein, F. (2010). “Approximate synthesis of four-bar linkages.” Resonance, 15(8), 740–767.
Housner, G. W. (1963). “The behavior of inverted pendulum structures during earthquakes.” Bull. Seismol. Soc. Am., 53(2), 403–417.
Kafle, B., Lam, N. T., Gad, E. F., and Wilson, J. (2011). “Displacement controlled rocking behaviour of rigid objects.” Earthquake Eng. Struct. Dyn., 40(15), 1653–1669.
Kam, W. Y., Pampanin, S., Palermo, A., and Carr, A. J. (2010). “Self-centering structural systems with combination of hysteretic and viscous energy dissipations.” Earthquake Eng. Struct. Dyn., 39(10), 1083–1108.
Kelly, J. M., and Tsztoo, D. (1977). “Earthquake simulation testing of a stepping frame with energy-absorbing devices.” Bull. N. Z. Natl. Soc. Earthquake Eng., 10(4), 196–207.
Makris, N., and Vassiliou, M. F. (2012). “Planar rocking response and stability analysis of an array of free-standing columns capped with a freely supported rigid beam.” Earthquake Eng. Struct. Dyn., 42(3), 431–449.
Makris, N., and Vassiliou, M. F. (2014). “Are some top-heavy structures more stable?” J. Struct. Eng., 06014001.
Makris, N., and Zhang, J. (2001). “Rocking response of anchored blocks under pulse-type motions.” J. Eng. Mech., 484–493.
Mander, J. B., and Cheng, C.-T. (1997). “Seismic resistance of bridge piers based on damage avoidance design.” Technical Rep., National Center for Earthquake Engineering Research, State Univ. of New York, Buffalo, New York.
Marriott, D., Pampanin, S., and Palermo, A. (2009). “Quasi-static and pseudo-dynamic testing of unbonded post-tensioned rocking bridge piers with external replaceable dissipaters.” Earthquake Eng. Struct. Dyn., 38(3), 331–354.
Oppenheim, I. J. (1992). “The masonry arch as a four-link mechanism under base motion.” Earthquake Eng. Struct. Dyn., 21(11), 1005–1017.
Palermo, A., Pampanin, S., and Calvi, G. M. (2005). “Concept and development of hybrid solutions for seismic resistant bridge systems.” J. Earthquake Eng., 9(6), 899–921.
Palermo, A., Pampanin, S., and Marriott, D. (2007). “Design, modeling, and experimental response of seismic resistant bridge piers with posttensioned dissipating connections.” J. Struct. Eng., 1648–1661.
Pang, J. B., Stanton, J. F., and Eberhard, M. O. (2008). “A precast concrete bridge bent designed to re-center after an earthquake.” Research Rep., Washington State Transportation Center, Univ. of Washington, Seattle, Washington.
Papaloizou, L., and Komodromos, P. (2009). “Planar investigation of the seismic response of ancient columns and colonnades with epistyles using a custom-made software.” Soil Dyn. Earthquake Eng., 29(11), 1437–1454.
Papaloizou, L., and Komodromos, P. (2012). “Investigating the seismic response of ancient multi-drum colonnades with two rows of columns using an object-oriented designed software.” Adv. Eng. Software, 44(1), 136–149.
Pollino, M., and Bruneau, M. (2007). “Seismic retrofit of bridge steel truss piers using a controlled rocking approach.” J. Bridge Eng., 600–610.
Priestley, M. N., Seible, F., and Calvi, G. M. (1996). Seismic design and retrofit of bridges, Wiley, New York.
Priestley, M. N., and Tao, J. R. (1993). “Seismic response of precast prestressed concrete frames with partially debonded tendons.” PCI J., 38(1), 58–69.
Prieto, F., Lourenço, P. B., and Oliveira, C. (2004). “Impulsive Dirac-delta forces in the rocking motion.” Earthquake Eng. Struct. Dyn., 33(7), 839–857.
Psycharis, I. N., Fragiadakis, M., and Stefanou, I. (2013). “Seismic reliability assessment of classical columns subjected to near-fault ground motions.” Earthquake Eng. Struct. Dyn., 42(14), 2061–2079.
Ricker, N. (1943). “Further developments in the wavelet theory of seismogram structure.” Bull. Seismol. Soc. Am., 33(3), 197–228.
Ricker, N. (1944). “Wavelet functions and their polynomials.” Geophysics, 9(3), 314–323.
Roh, H., and Reinhorn, A. M. (2010). “Modeling and seismic response of structures with concrete rocking columns and viscous dampers.” Eng. Struct., 32(8), 2096–2107.
Sakai, J., and Mahin, S. A. (2004). “Mitigation of residual displacements of circular reinforced concrete bridge columns.” Proc., 13th World Conf. on Earthquake Engineering, Vancouver, Canada.
Skinner, R., Tyler, R., Heine, A., and Robinson, W. (1980). “Hysteretic dampers for the protection of structures from earthquakes.” Bull. N. Z. Natl. Soc. Earthquake Eng., 13(1), 22–36.
Solberg, K., Mashiko, N., Mander, J., and Dhakal, R. (2009). “Performance of a damage-protected highway bridge pier subjected to bidirectional earthquake attack.” J. Struct. Eng., 469–478.
Structural Engineers Association of California (SEA), Applied Technology Council (ATC) and Consortium of Universities for Research in Earthquake Engineering (CUREE). (1997). “Suites of earthquake ground motions.” 〈http://nisee.berkeley.edu/data/strong_motion/sacsteel/ground_motions.html〉 (Jan. 10, 2014).
Vassiliou, M. F., and Makris, N. (2011). “Estimating time scales and length scales in pulselike earthquake acceleration records with wavelet analysis.” Bull. Seismol. Soc. Am., 101(2), 596–618.
Voyagaki, E., Psycharis, I. N., and Mylonakis, G. (2013). “Rocking response and overturning criteria for free standing rigid blocks to single—lobe pulses.” Soil Dyn. Earthquake Eng., 46, 85–95.
Wacker, J. M., Hieber, D. G., Stanton, J. F., and Eberhard, M. O. (2005). “Design of precast concrete piers for rapid bridge construction in seismic regions.” Research Rep., Washington State Transportation Center, Univ. of Washington, Seattle, Washington.
Zulli, D., Contento, A., and Di Egidio, A. (2012). “3D model of rigid block with a rectangular base subject to pulse-type excitation.” Int. J. Non Linear Mech., 47(6), 679–687.
Information & Authors
Information
Published In
Journal of Engineering Mechanics
Volume 141 • Issue 7 • July 2015
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jun 12, 2014
Accepted: Jan 26, 2015
Published online: Apr 15, 2015
Published in print: Jul 1, 2015
Discussion open until: Sep 15, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.