Compressive Behavior of Steel-FRP Composite Bars Confined with Low Elastic Modulus FRP Spirals in Concrete Columns
Publication: Journal of Composites for Construction
Volume 26, Issue 5
Abstract
This paper provides an experimental study on the compressive behavior of steel fiber–reinforced polymer composite bars (SFCBs) confined in concrete columns. Thirty reduced-scale concrete columns, reinforced with different longitudinal SFCBs and fiber-reinforced polymer spirals, were tested under monotonic compression. The results showed that the maximum compressive peak stress of the SFCBs was approximately 50% of their tensile strength, and it was generally lower for those SFCBs that had a relatively high postyield stiffness ratio. The postyield stage of the compressive stress–strain curve of well-confined SFCBs did not develop with a stable postyield stiffness as in nonconfined monotonic compression, but first developed with a stiffness almost equal to zero and then increased rapidly until the compressive peak stress point was reached, which was potentially due to the forced transverse deformation effect. Because the actual compressive contribution of the SFCBs in concrete columns could be overestimated due to this effect, a tentative modification method was first proposed in this paper to calibrate the existing compressive stress–strain model of the SFCBs.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge financial support from the National Natural Science Foundation of China (Grant No: 52008211), the National Natural Science Foundation of China (Grant No: 52127813), the National Natural Science Foundation of China (Grant No: 52178120), and the Foundation Research Project of Jiangsu Province (The Natural Science Foundation of Colleges and Universities No. 20KJB560015).
Notation
The following symbols are used in this paper:
- A
- cross-sectional area;
- Acol
- cross-sectional area of the column;
- Aeq
- equivalent cross-sectional area of the SFCB;
- Asf
- cross-sectional area of the SFCB;
- Asfeq
- equivalent cross-sectional area of the SFCB;
- D
- manually measured diameter of the rebar;
- Deq
- equivalent diameter of the SFCB;
- mean stress value of three f-type columns under compression;
- s
- spiral spacing;
- α and β
- coefficient of Eq. (3);
- Δtra
- transverse displacement of the control section of the SFCB;
- strain of the SFCB under compression;
- strain of the tensile peak point of the SFCB under tension;
- strain of the compressive peak point of the SFCB under compression;
- λ
- slenderness ratio;
- σc
- compressive strength of plain concrete;
- σcl/ch
- stress of the cl-f- (or ch-f)-type column under compression;
- compressive peak stress of the SFCB under compression;
- maximum positive value of ;
- ρlon
- longitudinal reinforcement ratio; and
- ρtra
- transverse reinforcement ratio.
References
AASHTO. 2020. LRFD bridge design specifications. 9th ed. Washington, DC: AASHTO.
ACI (American Concrete Institute). 2019. Building code requirements for structural concrete (ACI 318-19) and commentary. ACI 318-19. Farmington Hills, MI: ACI.
Ahmad, J., T. Yu, and M. N. S. Hadi. 2021. “Basalt fiber-reinforced polymer-confined geopolymer concrete.” ACI Struct. J. 118 (1): 289–300.
Ahmed, A., S. Guo, Z. Zhang, C. Shi, and D. Zhu. 2020. “A review on durability of fiber reinforced polymer (FRP) bars reinforced seawater sea sand concrete.” Constr. Build. Mater. 256 (2020): 119484. https://doi.org/10.1016/j.conbuildmat.2020.119484.
ASTM. 2014. Standard test method for static modulus of elasticity and Poisson’s ratio of concrete in compression. ASTM C469-14. West Conshohocken, PA: ASTM.
ASTM. 2016. Standard test method for tensile properties of fiber reinforced polymer matrix composite bars. ASTM D7205/D7205M-06. West Conshohocken, PA: ASTM.
ASTM. 2021. Standard test method for compressive strength of cylindrical concrete specimens. ASTM C39M-21. West Conshohocken, PA: ASTM.
Bae, S., A. M. Mieses, and O. Bayrak. 2005. “Inelastic buckling of reinforcing bars.” J. Struct. Eng. 131 (2): 314–321. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:2(314).
Bai, Y. 2014. Behavior and modeling of RC columns confined with large-rupture strain FRP composites. Hong Kong: The Hong Kong Polytechnic University.
Bai, Y.-L., J.-G. Dai, and J.-G. Teng. 2017a. “Monotonic stress–strain behavior of steel rebars embedded in FRP-confined concrete including buckling.” J. Compos. Constr. 21 (5): 04017043. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000823.
Bai, Y.-L., J.-G. Dai, and J. G. Teng. 2017b. “Buckling of steel reinforcing bars in FRP-confined RC columns: An experimental study.” Constr. Build. Mater. 140: 403–415. https://doi.org/10.1016/j.conbuildmat.2017.02.149.
Basaran, B., and I. Kalkan. 2020. “Development length and bond strength equations for FRP bars embedded in concrete.” Compos. Struct. 251 (2020): 112662. https://doi.org/10.1016/j.compstruct.2020.112662.
Deitz, D. H., I. E. Hark, and H. Gesund. 2003. “Physical properties of glass fiber reinforced polymer rebars in compression.” J. Compos. Constr. 7 (4): 363–366. https://doi.org/10.1061/(ASCE)1090-0268(2003)7:4(363).
Dhakal, R. P., and K. Maekawa. 2002. “Modeling for postyield buckling of reinforcement.” J. Struct. Eng., 128 (9): 1139–1147. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:9(1139).
Dong, Z., G. Wu, and Y. Xu. 2016. “Experimental study on the bond durability between steel-FRP composite bars (SFCBs) and sea sand concrete in ocean environment.” Constr. Build. Mater. 115: 277–284. https://doi.org/10.1016/j.conbuildmat.2016.04.052.
Dong, Z.-Q., G. Wu, X.-L. Zhao, and J.-L. Lian. 2018. “Long-term bond durability of fiber-reinforced polymer bars embedded in seawater sea-sand concrete under ocean environments.” J. Compos. Constr. 22 (5): 04018042. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000876.
Dong, Z., G. Wu, H. Zhu, X.-L. Zhao, Y. Wei, and H. Qian. 2020. “Flexural behavior of seawater sea-sand coral concrete–UHPC composite beams reinforced with BFRP bars.” Constr. Build. Mater. 265 (2020): 120279. https://doi.org/10.1016/j.conbuildmat.2020.120279.
Ge, W., K. Chen, Z. Guan, A. Ashour, W. Lu, and D. Cao. 2021. “Eccentric compression behaviour of concrete columns reinforced with steel-FRP composite bars.” Eng. Struct. 238: 112240. https://doi.org/10.1016/j.engstruct.2021.112240.
Ibrahim, A. I., G. Wu, and Z.-Y. Sun. 2017. “Experimental study of cyclic behavior of concrete bridge columns reinforced by steel basalt-fiber composite bars and hybrid stirrups.” J. Compos. Constr. 21 (2): 04016091. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000742.
Li, Y. L., J. G. Teng, X. L. Zhao, and R. K. S. Raman. 2018. “Theoretical model for seawater and sea sand concrete-filled circular FRP tubular stub columns under axial compression.” Eng. Struct. 160: 71–84. https://doi.org/10.1016/j.engstruct.2018.01.017.
Maranan, G. B., A. C. Manalo, B. Benmokrane, W. Karunasena, and P. Mendis. 2016. “Behavior of concentrically loaded geopolymer-concrete circular columns reinforced longitudinally and transversely with GFRP bars.” Eng. Struct. 117: 422–436. https://doi.org/10.1016/j.engstruct.2016.03.036.
Monti, G., and C. Nuti. 1992. “Nonlinear cyclic behavior of reinforcing bars including buckling.” J. Struct. Eng. 118 (12): 3268–3284. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:12(3268).
Solyom, S., and G. L. Balázs. 2021. “Analytical and statistical study of the bond of FRP bars with different surface characteristics.” Compos. Struct. 270 (2021): 113953. https://doi.org/10.1016/j.compstruct.2021.113953.
Sun, Z., G. Wu, J. Zhang, Y. Zeng, and W. Xiao. 2017. “Experimental study on concrete columns reinforced by hybrid steel-fiber reinforced polymer (FRP) bars under horizontal cyclic loading.” Constr. Build. Mater. 130: 202–211. https://doi.org/10.1016/j.conbuildmat.2016.10.001.
Sun, Z.-Y., G. Wu, Z.-S. Wu, and J. Zhang. 2014. “Nonlinear behavior and simulation of concrete columns reinforced by steel-FRP composite bars.” J. Bridge Eng. 19 (2): 220–234. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000515.
Sun, Z. Y., G. Wu, Z. S. Wu, M. Zhang, and X. Q. Hu. 2009. “Experimental study on the bond behavior between steel fiber composite bar (SFCB) and concrete.” Earthquake Resistant Eng. Retrofitting 31 (1): 21–27.
Tang, Y., Z. Sun, G. Wu, and Y. Wei. 2021. “Experimental study on cyclic behavior of SFCBs with different slenderness ratios.” J. Mater. Civ. Eng. 33 (8): 04021204. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003831.
Tang, Y., Z. Sun, and G. Wu. 2019. “Compressive behavior of sustainable steel-FRP composite bars with different slenderness ratios.” Sustainability 11 (4): 1118. https://doi.org/10.3390/su11041118.
Tavassoli, A., J. Liu, and S. Sheikh. 2015. “Glass fiber-reinforced polymer-reinforced circular columns under simulated seismic loads.” ACI Struct. J. 112 (1): 103–114. https://doi.org/10.14359/51687227.
Teng, J. G., J. F. Chen, S. T. Smith, and L. Lam. 2002. FRP: Strengthened RC structures. Weinheim, Germany: Wiley.
Wang, Y., G. Chen, B. Wan, B. Han, and J. Ran. 2021. “Axial compressive behavior and confinement mechanism of circular FRP-steel tubed concrete stub columns.” Compos. Struct. 256 (2021): 113082. https://doi.org/10.1016/j.compstruct.2020.113082.
Wu, G., Z. T. Lü, and Z. S. Wu. 2006. “Strength and ductility of concrete cylinders confined with FRP composites.” Constr. Build. Mater. 20 (3): 134–148. https://doi.org/10.1016/j.conbuildmat.2005.01.022.
Wu, G., Z.-S. Wu, Y.-B. Luo, Z.-Y. Sun, and X.-Q. Hu. 2010. “Mechanical properties of steel-FRP composite bar under uniaxial and cyclic tensile loads.” J. Mater. Civ. Eng. 22 (10): 1056–1066. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000110.
Wu, Z. S., X. Wang, and K. Iwashita. 2008. “Development of high performance structures with hybrid FRP composites.” In Vols. 1 and 2 of Proc., 10th Int. Symp. On Structural Engineering for Young Experts, 11–20.
Xue, W., F. Peng, and Z. Fang. 2018. “Behavior and design of slender rectangular concrete columns longitudinally reinforced with fiber-reinforced polymer bars.” ACI Struct. J. 115 (2): 311–322.
Zhou, Y., H. Gao, Z. Hu, Y. Qiu, M. Guo, X. Huang, and B. Hu. 2021. “Ductile, durable, and reliable alternative to FRP bars for reinforcing seawater sea-sand recycled concrete beams: Steel/FRP composite bars.” Constr. Build. Mater. 269: 121264. https://doi.org/10.1016/j.conbuildmat.2020.121264.
Zhou, Y., X. Zheng, F. Xing, L. Sui, Y. Zheng, and X. Huang. 2020. “Investigation on the electrochemical and mechanical performance of CFRP and steel-fiber composite bar used for impressed current cathodic protection anode.” Constr. Build. Mater. 255: 119377. https://doi.org/10.1016/j.conbuildmat.2020.119377.
Zhou, Y., Y. Zheng, J. Pan, L. Sui, F. Xing, H. Sun, and P. Li. 2019. “Experimental investigations on corrosion resistance of innovative steel-FRP composite bars using X-ray microcomputed tomography.” Composites, Part B 161: 272–284. https://doi.org/10.1016/j.compositesb.2018.10.069.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Dec 18, 2021
Accepted: May 25, 2022
Published online: Jul 21, 2022
Published in print: Oct 1, 2022
Discussion open until: Dec 21, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Shu Fang, Lijuan Li, Zhenpeng Luo, Zhuangcheng Fang, Dongchao Huang, Feng Liu, Hongliang Wang, Zhe Xiong, Novel FRP interlocking multi-spiral reinforced-seawater sea-sand concrete square columns with longitudinal hybrid FRP–steel bars: Monotonic and cyclic axial compressive behaviours, Composite Structures, 10.1016/j.compstruct.2022.116487, 305, (116487), (2023).
- Jie Liu, Yu Yuan, Libin Wang, Zhongxiang Liu, Jun Yang, Parameter Study of Interfacial Capacities for FRP–Steel Bonded Joints Based on 3D FE Modeling, Materials, 10.3390/ma15217787, 15, 21, (7787), (2022).
- Yunlou Sun, Jinyu Fu, Zeyang Sun, Jian Zhang, Yang Wei, Gang Wu, Flexural behavior of concrete beams reinforced by partially unbonded steel-FRP composite bars, Engineering Structures, 10.1016/j.engstruct.2022.115050, 272, (115050), (2022).