Numerical Modeling and Performance Assessment of Bridge Column Strengthened by FRP and Polyurea under Combined Collision and Blast Loading
Publication: Journal of Composites for Construction
Volume 26, Issue 2
Abstract
Highway bridge piers could be underdesigned for a multihazardous condition involving vehicle collision and air blast based on the current design code. The piers are often positioned in such a fashion that it is neither possible nor economically feasible to place protective devices around them. This paper numerically investigated two potential strengthening techniques, the placement of a fiber-reinforced polymer (FRP) wrap and polyurea coating onto the column surface, to improve column resistance against the extreme demands from combined collision and blast loads. Finite-element models of isolated reinforced concrete (RC) columns with an FRP wrap and polyurea coating were developed using a commercial software, LS-DYNA. The modeling techniques were validated separately against impact and blast experimental results. Collisions were supplied from a medium-size F800 single-unit truck at various velocities, and air blasts of varying magnitude were represented using the arbitrary Lagrangian–Eulerian approach. Bare and strengthened column response to various collision and blast demands was compared to assess the effectiveness of strengthening. The results indicated that using the FRP wrap and polyurea coating on columns could effectively mitigate the effects of combined vehicle collision and air blast. The effectiveness of each scheme differed as a function of geometric and material properties and column demands. Parametric studies were then conducted to evaluate the influences of various design parameters on column performance and identify optimal strengthening schemes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded, in part, by the Mid-America Transportation Center via a grant from the US Department of Transportation’s University Transportation Centers Program, and this support is gratefully acknowledged. The authors would like to gratefully acknowledge the University of Nebraska’s Holland Computing Center for providing computational resources.
References
AASHTO. 2017. Load and resistance factor design (LRFD) bridge design specifications. Washington, DC: AASHTO.
Abdelkarim, O. I., and M. A. ElGawady. 2016. “Performance of hollow-core FRP–concrete–steel bridge columns subjected to vehicle collision.” Eng. Struct. 123: 517–531. https://doi.org/10.1016/j.engstruct.2016.05.048.
Ackland, K., C. Anderson, and T. D. Ngo. 2013. “Deformation of polyurea-coated steel plates under localised blast loading.” Int. J. Impact Eng. 51: 13–22. https://doi.org/10.1016/j.ijimpeng.2012.08.005.
AuYeung, S., and A. Alipour. 2016. “Evaluation of AASHTO suggested design values for reinforced concrete bridge piers under vehicle collisions.” Transp. Res. Rec. 2592: 1–8. https://doi.org/10.3141/2592-01.
Brown, M. D., and A. S. Loewe. 2011. Reference manual to mitigate potential terrorist attacks against buildings. FEMA 426. Washington, DC: US Dept. of Homeland Security Federal Emergency Management Agency.
Chan, S., Z. Fawaz, K. Behdinan, and R. Amid. 2007. “Ballistic limit prediction using a numerical model with progressive damage capability.” Compos. Struct. 77 (4): 466–474. https://doi.org/10.1016/j.compstruct.2005.08.022.
Chen, C. C., and D. G. Linzell. 2014. “Numerical simulations of dynamic behavior of polyurea toughened steel plates under impact loading.” J. Comput. Eng. 2014: 416049.
Dai, L. H., C. Wu, F. J. An, and S. S. Liao. 2018. “Experimental investigation of polyurea-coated steel plates at underwater explosive loading.” Adv. Mater. Sci. Eng. 2018: 1264276.
Davidson, J. S., S. Sudame, and R. J. Dinan. 2004. Development of computational models and input sensitivity study of polymer reinforced concrete masonry walls subjected to blast. Birmingham, AL: Dept. of Civil and Environmental Engineering, Univ. of Alabama at Birmingham.
Dinan, R., J. Fisher, M. I. Hammons, and J. R. Porter. 2003. Failure mechanisms in unreinforced concrete masonry walls retrofitted with polymer coatings. Tyndall AFB, FL: Air Force Research Laboratory.
El-Tawil, S., E. Severino, and P. Fonseca. 2005. “Vehicle collision with bridge piers.” J. Bridge Eng. 10 (3): 345–353. https://doi.org/10.1061/(ASCE)1084-0702(2005)10:3(345).
Erki, M., and U. Meier. 1999. “Impact loading of concrete beams externally strengthened with CFRP laminates.” J. Compos. Constr. 3 (3): 117–124. https://doi.org/10.1061/(ASCE)1090-0268(1999)3:3(117).
Eugene Kim, K. H., and B. Andrawes. 2017. “Load rating of deteriorated and FRP-retrofitted bridge abutment timber piles.” J. Bridge Eng. 22 (9): 04017058. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001090.
Fang, C., T. Y. Yosef, D. G. Linzell, and J. D. Rasmussen. 2021a. “Computational modeling and dynamic response of highway bridge columns subjected to combined vehicle collision and air blast.” Eng. Fail. Anal. 125 (2021): 105389. https://doi.org/10.1016/j.engfailanal.2021.105389.
Fang, C., T. Y. Yosef, D. G. Linzell, and J. D. Rasmussen. 2021b. “Residual axial capacity estimates for bridge columns subjected to combined vehicle collision and air blast.” J. Bridge Eng. 26 (7): 04021035. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001735.
Hallquist, J. O. 2014. LS-DYNA keyword user’s manual. Livermore, CA: Livermore Software Technology Corp.
Han, H., F. Taheri, N. Pegg, and Y. Lu. 2007. “A numerical study on the axial crushing response of hybrid pultruded and ±45 braided tubes.” Compos. Struct. 80 (2): 253–264. https://doi.org/10.1016/j.compstruct.2006.05.012.
Hollaway, L. C., and J. G. Teng. 2008. Strengthening and rehabilitation of civil infrastructures using fibre-reinforced polymer (FRP) composites. Cambridge: Woodhead Publishing.
Iqbal, N., M. Tripathi, S. Parthasarathy, D. Kumar, and P. Roy. 2016. “Polyurea coatings for enhanced blast-mitigation: A review.” RSC Adv. 6 (111): 109706–109717. https://doi.org/10.1039/C6RA23866A.
Iqbal, N., P. Sharma, D. Kumar, and P. Roy. 2018. “Protective polyurea coatings for enhanced blast survivability of concrete.” Constr. Build. Mater. 175: 682–690. https://doi.org/10.1016/j.conbuildmat.2018.04.204.
Jacques, E., A. Lloyd, P. Imbeau, D. Palermo, and J. Quek. 2015. “GFRP-retrofitted reinforced concrete columns subjected to simulated blast loading.” J. Struct. Eng. 141 (11): 04015028. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001251.
Jayasinghe, L. B., D. P. Thambiratnam, N. Perera, and J. Jayasooriya. 2013. “Computer simulation of underground blast response of pile in saturated soil.” Comput. Struct. 120: 86–95. https://doi.org/10.1016/j.compstruc.2013.02.016.
Koneshwaran, S., D. P. Thambiratnam, and C. Gallage. 2015. “Blast response of segmented bored tunnel using coupled SPH–FE method.” Structures 2: 58–71. https://doi.org/10.1016/j.istruc.2015.02.001.
Lewis, B. A. 2004. Manual for LS-DYNA soil material model 147. Springfield, VA: Federal Highway Administration.
Liu, L., H. Feng, H. Tang, and Z. Guan. 2018. “Impact resistance of Nomex honeycomb sandwich structures with thin fibre reinforced polymer facesheets.” J. Sandwich Struct. Mater. 20 (5): 531–552. https://doi.org/10.1177/1099636216664076.
Malvar, L. J. 1998. “Review of static and dynamic properties of steel reinforcing bars.” Mater. J. 95 (5): 609–616.
Mohan, P., D. Marzougui, and C. D. Kan. 2006. “Validation of a single unit truck model for roadside hardware impact.” Int. J. Veh. Syst. Modell. Test. 2 (1): 1–15.
Mohotti, D., M. Ali, T. Ngo, J. Lu, and P. Mendis. 2014. “Strain rate dependent constitutive model for predicting the material behaviour of polyurea under high strain rate tensile loading.” Mater. Des. 53: 830–837. https://doi.org/10.1016/j.matdes.2013.07.020.
Murray, Y. D. 2007. Users manual for LS-DYNA concrete material model 159. McLean, VA: U.S. Dept. of Transportation.
Murray, Y. D., A. Y. Abu-Odeh, and R. P. Bligh. 2007. Evaluation of LS-DYNA concrete material model 159. McLean, VA: U.S. Dept. of Transportation.
Mutalib, A. A., and H. Hao. 2010. “Numerical analysis of FRP-composite-strengthened RC panels with anchorages against blast loads.” J. Perform. Constr. Facil. 25 (5): 360–372. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000199.
Mutalib, A. A., and H. Hao. 2011. “Development of P–I diagrams for FRP strengthened RC columns.” Int. J. Impact Eng. 38 (5): 290–304. https://doi.org/10.1016/j.ijimpeng.2010.10.029.
Nam, J. W., H. J. Kim, S. B. Kim, N. H. Yi, and J. H. J. Kim. 2010. “Numerical evaluation of the retrofit effectiveness for GFRP retrofitted concrete slab subjected to blast pressure.” Compos. Struct. 92 (5): 1212–1222. https://doi.org/10.1016/j.compstruct.2009.10.031.
Natalia, L. C., J. M. John, A. Domenico, M. Costantino, and P. Andrea. 2018. “Polyurea coated and plane reinforced concrete panel behavior under blast loading: numerical simulation to experimental results.” Trends Civ. Eng. Archit. 1 (4): 1–12.
Nystrom, H. E., S. E. Watkins, A. Nanni, and S. Murray. 2003. “Financial viability of fiber-reinforced polymer (FRP) bridges.” J. Manage. Eng. 19 (1): 2–8. https://doi.org/10.1061/(ASCE)0742-597X(2003)19:1(2).
O’Hare, E. V. 2011. “Computational assessment of steel-jacketed bridge pier column performance under blast loads.” Master’s thesis, Dept. of Civil and Environmental Engineering, Pennsylvania State Univ., State College.
Pham, T. M., and H. Hao. 2016. “Impact behavior of FRP-strengthened RC beams without stirrups.” J. Compos. Constr. 20 (4): 04016011. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000671.
Razaqpur, A. G., A. Tolba, and E. Contestabile. 2007. “Blast loading response of reinforced concrete panels reinforced with externally bonded GFRP laminates.” Composites, Part B 38 (5–6): 535–546. https://doi.org/10.1016/j.compositesb.2006.06.016.
Reese, L., T. Qiu, D. G. Linzell, E. O'hare, and Z. Rado. 2014. “Field tests and numerical modeling of vehicle impacts on a boulder embedded in compacted fill.” Int. J. Prot. Struct. 5 (4): 435–451. https://doi.org/10.1260/2041-4196.5.4.435.
Reid, J. D., B. A. Coon, B. A. Lewis, S. H. Sutherland, and Y. D. Murray. 2004. Evaluation of LS-DYNA soil material model 147. McLean, VA: Federal Highway Administration.
Roland, C., J. Twigg, Y. Vu, and P. Mott. 2007. “High strain rate mechanical behavior of polyurea.” Polymer 48 (2): 574–578. https://doi.org/10.1016/j.polymer.2006.11.051.
Ross, C. A., M. R. Purcell, and E. L. Jerome. 1997. “Blast response of concrete beams and slabs externally reinforced with fiber reinforced plastics (FRP).” In Proc., 15th Structures Congress, 673–677. Reston, VA: ASCE.
Saleh, M., and L. Edwards. 2015. “Evaluation of soil and fluid structure interaction in blast modelling of the flying plate test.” Comput. Struct. 151: 96–114. https://doi.org/10.1016/j.compstruc.2015.01.010.
Sen, R., and G. Mullins. 2007. “Application of FRP composites for underwater piles repair.” Composites, Part B 38 (5–6): 751–758. https://doi.org/10.1016/j.compositesb.2006.07.011.
Sha, Y., and H. Hao. 2015. “Laboratory tests and numerical simulations of CFRP strengthened RC pier subjected to barge impact load.” Int. J. Struct. Stab. Dyn. 15 (2): 1450037. https://doi.org/10.1142/S0219455414500370.
Sharma, H., S. Hurlebaus, and P. Gardoni. 2012. “Performance-based response evaluation of reinforced concrete columns subject to vehicle impact.” Int. J. Impact Eng. 43: 52–62. https://doi.org/10.1016/j.ijimpeng.2011.11.007.
Soden, P., M. Hinton, and A. Kaddour. 2004. “Lamina properties, lay-up configurations and loading conditions for a range of fibre reinforced composite laminates.” In Failure criteria in fibre-reinforced-polymer composites, edited by M. J. Hinton, A. S. Kaddour, and P. D. Soden, 30–51. Amsterdam, Netherlands: Elsevier.
Tennessean News. 2014. “Tennessean News Archive.” Accessed August 15, 2014. https://www.tennessean.com/story/news/local/williamson/2014/08/15/franklin-tanker-explosion-65/14097717/.
Tuhin, I., and M. Tazarv. 2020. “Stress–strain relationship for polyurea-confined circular concrete columns under static loads.” ACI Mater. J. 117 (4): 81–94.
Wang, J., H. Ren, X. Wu, and C. Cai. 2017. “Blast response of polymer-retrofitted masonry unit walls.” Composites, Part B 128: 174–181. https://doi.org/10.1016/j.compositesb.2016.02.044.
Wang, W., C. Wu, and J. Li. 2018. “Numerical simulation of hybrid FRP–concrete–steel double-skin tubular columns under close-range blast loading.” J. Compos. Constr. 22 (5): 04018036. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000871.
Wassef, W., C. Smith, C. Clancy, and M. Smith. 2003. Comprehensive design example for prestressed concrete (PSC) girder superstructure bridge with commentary. Washington, DC: US Government Printing Office, Federal Highway Administration.
Williamson, E. B. 2010. Blast-resistant highway bridges: Design and detailing guidelines. NCHRP654. Washington, DC: Transportation Research Board, National Academies of Sciences, Engineering, Medicine.
Wu, K. C., B. Li, and K. C. Tsai. 2011. “Residual axial compression capacity of localized blast-damaged RC columns.” Int. J. Impact Eng. 38 (1): 29–40. https://doi.org/10.1016/j.ijimpeng.2010.09.002.
Xu, J., C. Demartino, B. Shan, Y. Heo, and Y. Xiao. 2020. “Experimental investigation on performance of cantilever CFRP-wrapped circular RC columns under lateral low-velocity impact.” Compos. Struct. 242: 112143. https://doi.org/10.1016/j.compstruct.2020.112143.
Zhang, Z. 2004. “Investigation on dynamic pulse buckling and damage behavior of composite laminated beams subject to axial impulse.” Ph.D. thesis, Dept. of Civil and Resource Engineering, Dalhousie Univ.
Information & Authors
Information
Published In
Copyright
© 2022 American Society of Civil Engineers.
History
Received: Apr 4, 2021
Accepted: Nov 13, 2021
Published online: Jan 12, 2022
Published in print: Apr 1, 2022
Discussion open until: Jun 12, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Xiuchen Xu, Hongchao Zhang, Xiaobo Du, Qiang Liu, Vehicle collision with RC structures: A state-of-the-art review, Structures, 10.1016/j.istruc.2022.08.107, 44, (1617-1635), (2022).