Conformable Tire Patch Loading for FRP Composite Bridge Deck
Publication: Journal of Composites for Construction
Volume 13, Issue 6
Abstract
Fiber-reinforced polymer (FRP) composites are increasingly being used in bridge deck applications. However, there are currently only fledgling standards to design and characterize FRP deck systems. One area that should be addressed is the loading method for the FRP deck. It has been observed that the type of loading patch greatly influences the failure mode of a cellular FRP deck. The contact pressure distribution of a real truck loading is nonuniform with more concentration near the center of the contact area as a result of the conformable contact mechanics. Conversely, the conventional rectangular steel patch on a FRP deck act like a rigid flat punch and produces stress concentration near the edges. A proposed simulated tire patch has been examined for loading a cellular FRP deck with the load distribution characterized by a pressure sensitive film sensor and three-dimensional contact analysis using ANSYS. A loading profile is proposed as a design tool for analyzing FRP deck systems for strength and durability. Local top surface strains and displacements of the cellular FRP deck are found to be higher with proposed loading profile compared to those for the conventional uniformly distributed loading. Parametric studies on the deck geometry show that the global displacement criterion used for characterizing bridge deck is inadequate for a cellular FRP deck and that the local effects must be considered.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers gratefully acknowledge the financial support of the Virginia Transportation Research Council (Contract No. UNSPECIFIEDVTRC-MOA-03–010) and Virginia Department of Transportation (VDOT).
References
AASHTO. (1996). “Standard specifications for highway bridges.” American Association of State Highway and Transportation Officials, Washington, D.C.
AASHTO-LRFD. (1998). “Design specifications.” 2nd Ed., American Association of State Highway and Transportation Officials, Washington, D.C.
ANSYS. (2007). ANSYS theory reference, ⟨http://www.ansys.com⟩ (June 1, 2008).
Blab, R. (1999). “Introducing improved loading assumptions into analytical pavement models based on measured contact stresses of tires.” Proc., Int. Conf. on Accelerated Pavement Testing, Transportation Research Board, Reno, Nev.
Coleman, J. T. (2002). “Continuation of field and laboratory tests of a proposed bridge deck panel fabricated from pultruded fiber-reinforced polymer components.” MS thesis, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Davalos, J. F., Qiao, P., Frank Xu, X., Robinson, J., and Barth, K. E. (2001). “Modeling and characterization of fiber-reinforced plastic honeycomb sandwich panels for highway bridge applications.” Compos. Struct., 52(3–4), 441–452.
De Beer, M. (1996). “Measurement of tyre/pavement interface stresses under moving wheel loads.” Heavy Vehicle Sys., Int. J. Vehicle Des., 3(1), 97–115.
De Beer, M., Sadzik, E. M., Fisher, C., and Coetzee, C. H. (2005). “Tyre-pavement contact stress patterns from the test tyres of the Gautrans Heavy Vehicle Simulator (HVS) MK .” Proc., 24th Annual Southern African Transport Conf. and Exhibition, Document Transformation Technologies, Pretoria, South Africa.
Faraji, A. (2005). Elastic and elastoplastic contact analysis: Using boundary elements and mathematical programming, WIT, Southampton, U.K.
Fernando, E. G., Musani, D., Park, D. W., and Liu, W. (2006). Evaluation of effects of tire size and inflation pressure on tire contact stresses and pavement response, Texas Transportation Institute, Austin, Tex.
GangaRao, H. V. S., and Vali, A. (1990). “Truck-tire steel grid deck contact pressure distributions.” J. Struct. Eng., 116(3), 791–808.
Gladwell, G. M. L. (1980). Contact problems in the classical theory of elasticity, Sijthoff & Noordhoff, Alphen aan den Rijn, The Netherlands.
Johnson, K. L. (1985). Contact mechanics, Cambridge University Press, Cambridge, Cambridgeshire, New York.
Laursen, T. A. (2002). Computational contact and impact mechanics: Fundamentals of modeling interfacial phenomena in nonlinear finite element analysis, Springer, Berlin.
Majumdar, P. K. (2008). “Strength and life prediction of FRP composite bridge deck.” Ph.D. dissertation, Virginia Tech, Blacksburg, Va.
Majumdar, P. K., Liu, Z., Lesko, J. J., and Cousins, T. E. (2007). “Evaluation of FRP composite deck for bridge rehabilitation.” Proc., SAMPE 2007, Society for the Advancement of Material and Process Engineering (SAMPE), Baltimore.
Marshek, K. M., Chen, H. H., Connell, R. B., and Saraf, C. L. (1986). “Effect of truck tire inflation pressure and axle load on flexible and rigid pavement performance.” Transp. Res. Rec., 1070, 14–21.
Myers, L. A., Roque, R., Ruth, B. E., and Drakos, C. (1999). “Measurement of contact stresses for different truck tire types to evaluate their influence on near-surface cracking and rutting.” Transp. Res. Rec., 1655, 175–184.
Pottinger, M. G. (1992). “Three-dimensional contact patch stress field of solid and pneumatic tires.” Tire Sci. Technol., 20(1), 3–32.
Pottinger, M. G., and McIntyre, J. E., III. (1999). “Effect of suspension alignment and modest cornering on the footprint behavior of performance tires and heavy duty radial tires.” Tire Sci. Technol., 27(3), 128–160.
Prozzi, J. A., and Luo, R. (2005). “Quantification of the joint effect of wheel load and tire inflation pressure on pavement response.” Transp. Res. Rec., 1919, 134–141.
Society of the Plastics Industry, Inc. (2007). Sensor Products Inc., ⟨http://www.pressurex.com⟩ (June 1, 2007).
Soon, S. -C., Drescher, A., and Stolarski, H. K. (2004). “Tire-induced surface stresses in flexible pavements.” Transp. Res. Rec.1896, 170–176.
Strongwell. (2007). Strongwell design manual, ⟨www.strongwell.com⟩ (Oct. 27, 2008).
Temeles, A. B. (2001). “Field and laboratory tests of a proposed bridge deck panel fabricated from pultruded fiber-reinforced polymer components.” MS Thesis, Virginia Polytechnic Institute and State University, Blacksburg, Va.
Tielking, J. T., and Abraham, M. A. (1994). Measurement of truck tire footprint pressures, National Research Council, Washington, D.C.
Tielking, J. T., and Roberts, F. L. (1987). “Tire contact pressure and its effect on pavement strain.” J. Transp. Eng., 113(1), 56–71.
Wang, F., and Machemehl, R. (2006a). Predicting truck tire pressure effects upon pavement performance, Center for Transportation Research, Univ. of Texas, Austin, Tex.
Wang, F., and Machemehl, R. B. (2005). “Analysis of effects of truck tire pressure on flexible pavements.” Canadian Society for Civil Engineers, Toronto, Canada.
Wang, F., and Machemehl, R. B. (2006b). “Mechanistic-empirical study of effects of truck tire pressure on pavement: Measured tire-pavement contact stress data.” Transp. Res. Rec., 1947, 136–145.
Wriggers, P. (2006). Computational contact mechanics, Springer, New York.
Yue, Z. Q., and Svec, O. J. (1995). “Effects of tire-pavement contact pressure distributions on the response of asphalt concrete pavements.” Can. J. Civ. Eng., 22(5), 849–860.
Zhou, A. (2002). “Stiffness and strength of fiber reinforced polymer composite bridge deck systems.” Ph.D. dissertation, Virginia Polytechnic Institute and State Univ., Blacksburg, Va.
Zhou, A., Coleman, J. T., Temeles, A. B., Lesko, J. J., and Cousins, T. E. (2005). “Laboratory and field performance of cellular fiber-reinforced polymer composite bridge deck systems.” J. Compos. Constr., 9(5), 458–467.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Jul 3, 2008
Accepted: Feb 24, 2009
Published online: Nov 13, 2009
Published in print: Dec 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.