Yielding Steel Dampers as Restraining Devices to Control Seismic Sliding of Laminated Rubber Bearings for Highway Bridges: Analytical and Experimental Study
Publication: Journal of Bridge Engineering
Volume 24, Issue 11
Abstract
The performance of concrete shear keys as restraining devices for laminated rubber bearing–supported highway bridges was examined in past earthquakes such as the 1999 Chi-Chi and the 2008 Wenchuan earthquakes, where the widely observed shear key failure and bearing sliding significantly increased the risk of span unseating. To avoid such scenarios, economical yielding steel dampers are proposed to replace conventional shear keys as restraining devices on bridges. If designed properly, the steel dampers are expected to control bearing displacement within limit without imposing much additional demand on the substructure. The primary objective of this study was to develop a simplified procedure for designing the yielding steel dampers to control sliding displacement of the laminated rubber bearings to a specified value for the considered earthquake hazard. By treating the global bridge system as a serial-parallel combination of different components, the correlations of various parameters were investigated. On that basis, a simple formulation was developed, followed by a series of nonlinear time history analyses and a shake table test as verifications. The outcome of this study highlights the cost-effectiveness of using yielding steel dampers and laminated rubber bearings as an earthquake-resistant system for highway bridges compared with other popular isolation systems. The proposed design procedure was also verified to be quite efficient in properly designing the yielding steel dampers for a satisfactory bridge seismic performance.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research is supported by the National Natural Science Foundation (51678434) of China, the Self-Innovation Project of SLDRCE of Tongji University (SLDRCE15-A-01), the Natural Sciences and Engineering Research Council (NSERC) of Canada through a Discovery Grant, and the UBC Faculty of Applied Science. The support is gratefully acknowledged.
References
AASHTO. 2010. Guide specifications for seismic isolation design. 3rd ed. Washington, DC: AASHTO.
AASHTO. 2011. Guide specifications for LRFD seismic bridge design. 2nd ed. Washington, DC: AASHTO.
Abrahamson, N. A. 1992. “Non-stationary spectral matching.” Seismol. Res. Lett. 63 (1): 30.
Aiken, I. D., D. K. Nims, A. S. Whittaker, and J. M. Kelly. 1993. “Testing of passive energy dissipation systems.” Earthq. Spectra 9 (3): 335–370. https://doi.org/10.1193/1.1585720.
Bergman, D. M., and S. C. Goel. 1987. Evaluation of cyclic testing of steel-plate devices for added damping and stiffness. Rep. No. UMCE 87–10. Ann Arbor, MI: Univ. of Michigan.
Bray, J. D., and A. Rodriguez-Marek. 2004. “Characterization of forward-directivity ground motions in the near-fault region.” Soil Dyn. Earthquake Eng. 24 (11): 815–828. https://doi.org/10.1016/j.soildyn.2004.05.001.
Buckle, I. G., M. C. Constantinou, M. Dicleli, and H. Ghasemi. 2006. Seismic isolation of highway bridges. Rep. No. MCEER-06-SP07. Buffalo, NY: Multidisciplinary Center for Earthquake Engineering Research.
Buckle, I., M. Hube, G. Chen, W. H. Yen, and J. Arias. 2012. “Structural performance of bridges in the offshore Maule earthquake of 27 February 2010.” Earthq. Spectra 28 (S1): S533–S552. https://doi.org/10.1193/1.4000031.
Camara, A., R. Cristantielli, M. A. Astiz, and C. Málaga-Chuquitaype. 2017. “Design of hysteretic dampers with optimal ductility for the transverse seismic control of cable-stayed bridges.” Earthquake Eng. Struct. Dyn. 46 (11): 1811–1833. https://doi.org/10.1002/eqe.2884.
Chang, K. C., K. Y. Kuo, K. Y. Liu, and C. H. Lu. 2004. “On seismic retrofit strategies of highway bridges-experiences learned from Chi-Chi earthquake.” In Proc., 13th World Conf. on Earthquake Engineering (WCEE), 639. Vancouver: International Association for Earthquake Engineering.
Chen, G., E. R. Bothe, and J. J. F. Ger. 2001. “Experimental characterization of metallic dampers for seismic retrofit of highway bridges.” Transp. Res. Rec. 1770 (1): 124–131. https://doi.org/10.3141/1770-16.
Chen, G., S. Eads, and B. A. Hartnagel. 2006. “Commonly used steel rods for cost-effective seismic retrofit of steel-girder bridges: Energy dissipation and fatigue properties.” In Proc., Structures Congress 2006: Structural Engineering and Public Safety, 1–15. Reston, VA: ASCE.
Chopra, A. K. 2011. Dynamics of structures: Theory and applications to earthquake engineering. 4th ed. Upper Saddle River, NJ: Pearson/Prentice Hall.
Constantinou, M., A. Mokha, and A. Reinhorn. 1990. “Teflon bearings in base isolation II: Modeling.” J. Struct. Eng. 116 (2): 455–474. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:2(455).
Dargush, G. F., and T. T. Soong. 1995. “Behavior of metallic plate dampers in seismic passive energy dissipation systems.” Earthq. Spectra 11 (4): 545–568. https://doi.org/10.1193/1.1585827.
Filipov, E. T., L. A. Fahnestock, J. S. Steelman, J. F. Hajjar, J. M. LaFave, and D. A. Foutch. 2013a. “Evaluation of quasi-isolated seismic bridge behavior using nonlinear bearing models.” Eng. Struct. 49: 168–181. https://doi.org/10.1016/j.engstruct.2012.10.011.
Filipov, E. T., J. R. Revell, L. A. Fahnestock, J. M. LaFave, J. F. Hajjar, D. A. Foutch, and J. S. Steelman. 2013b. “Seismic performance of highway bridges with fusing bearing components for quasi-isolation.” Earthquake Eng. Struct. Dyn. 42 (9): 1375–1394. https://doi.org/10.1002/eqe.2277.
Ghaffary, A., and R. Karami Mohammadi. 2018. “Framework for virtual hybrid simulation of TADAS frames using OpenSees and Abaqus.” J. Vib. Control 24 (11): 2165–2179. https://doi.org/10.1177/1077546316679029.
Golzan, S. B., S. Langlois, and F. P. Legeron. 2017. “Implementation of a simplified method in design of hysteretic dampers for isolated highway bridges.” J. Bridge Eng. 22 (3): 04016127. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001012.
Guan, Z., J. Li, and Y. Xu. 2010. “Performance test of energy dissipation bearing and its application in seismic control of a long-span bridge.” J. Bridge Eng. 15 (6): 622–630. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000099.
Han, Q., X. Du, J. Liu, Z. Li, L. Li, and J. Zhao. 2009. “Seismic damage of highway bridges during the 2008 Wenchuan earthquake.” Earthq. Eng. Eng. Vib. 8 (2): 263–273. https://doi.org/10.1007/s11803-009-8162-0.
Hancock, J., J. Watson-Lamprey, N. A. Abrahamson, J. J. Bommer, A. Markatis, E. McCoy, and R. Mendis. 2006. “An improved method of matching response spectra of recorded earthquake ground motion using wavelets.” J. Earthquake Eng. 10 (sup001): 67–89. https://doi.org/10.1080/13632460609350629.
Jara, J. M., G. Raya, B. A. Olmos, and G. Martinez. 2017. “Applicability of equivalent linearization methods to irregular isolated bridges.” Eng. Struct. 141: 495–511. https://doi.org/10.1016/j.engstruct.2017.03.052.
JTG/T. 2008. Guidelines for seismic design of highway bridge. [In Chinese.] Beijing: Communications Press.
Kelly, J. M., R. I. Skinner, and A. J. Heine. 1972. “Mechanisms of energy absorption in special devices for use in earthquake resistant structures.” Bull. N. Z. Soc. Earthq. Eng. 5 (3): 63–88.
Kwon, O. S., and S. H. Jeong. 2013. “Seismic displacement demands on skewed bridge decks supported on elastomeric bearings.” J. Earthquake Eng. 17 (7): 998–1022. https://doi.org/10.1080/13632469.2013.791894.
Li, J., T. Peng, and Y. Xu. 2008. “Damage investigation of girder bridges under the Wenchuan earthquake and corresponding seismic design recommendations.” Earthq. Eng. Eng. Vib. 7 (4): 337–344. https://doi.org/10.1007/s11803-008-1005-6.
Li, J., N. Xiang, H. Tang, and Z. Guan. 2016. “Shake-table tests and numerical simulation of an innovative isolation system for highway bridges.” Soil Dynam. Earthq. Eng. 86: 55–70. https://doi.org/10.1016/j.soildyn.2016.05.002.
Liu, C., R. Gao, and B. Guo. 2018. “Seismic design method analyses of an innovative steel damping bearing for railway bridges.” Eng. Struct. 167: 518–532. https://doi.org/10.1016/j.engstruct.2018.04.076.
Mahjoubi, S., and S. Maleki. 2017. “Pipe dampers as passive devices for seismic control of isolated bridges.” Struct. Control. Health Monit. 24 (2): e1869. https://doi.org/10.1002/stc.1869.
Mohammadi, R. K., A. Nasri, and A. Ghaffary. 2017. “TADAS dampers in very large deformations.” Int. J. Steel Struct. 17 (2): 515–524. https://doi.org/10.1007/s13296-017-6011-y.
Pan, P., H. Yan, T. Wang, P. Xu, and Q. Xie. 2014. “Development of steel dampers for bridges to allow large displacement through a vertical free mechanism.” Earthq. Eng. Eng. Vib. 13 (3): 375–388. https://doi.org/10.1007/s11803-014-0249-6.
PEER (Pacific Earthquake Engineering Research Center). 2018. PEER ground motion database. Berkeley, CA: PEER.
Priestley, M. N., M. C. Calvi, and M. J. Kowalsky. 2007. Displacement-based seismic design of structures. Pavia, Italy: IUSS Press.
Priestley, M. N., F. Seible, and G. M. Calvi. 1996. Seismic design and retrofit of bridges. New York: Wiley.
Schanack, F., G. Valdebenito, and J. Alvial. 2012. “Seismic damage to bridges during the 27 February 2010 magnitude 8.8 Chile earthquake.” Earthq. Spectra 28 (1): 301–315. https://doi.org/10.1193/1.3672424.
Shen, X., X. Wang, Q. Ye, and A. Ye. 2017. “Seismic performance of transverse steel damper seismic system for long span bridges.” Eng. Struct. 141: 14–28. https://doi.org/10.1016/j.engstruct.2017.03.014.
Shih, M. H., and W. P. Sung. 2005. “A model for hysteretic behavior of rhombic low yield strength steel added damping and stiffness.” Comput. Struct. 83 (12–13): 895–908. https://doi.org/10.1016/j.compstruc.2004.11.012.
Shih, M. H., W. P. Sung, and C. G. Go. 2004. “Investigation of newly developed added damping and stiffness device with low yield strength steel.” J. Zhejiang Univ. Sci. 5 (3): 326–334. https://doi.org/10.1631/jzus.2004.0326.
Skinner, R. I., J. L. Beck, and G. N. Bycroft. 1974a. “A practical system for isolating structures from earthquake attack.” Earthquake Eng. Struct. Dyn. 3 (3): 297–309. https://doi.org/10.1002/eqe.4290030308.
Skinner, R. I., J. M. Kelly, and A. J. Heine. 1974b. “Hysteretic dampers for earthquake-resistant structures.” Earthquake Eng. Struct. Dyn. 3 (3): 287–296. https://doi.org/10.1002/eqe.4290030307.
Steelman, J. S., L. A. Fahnestock, E. T. Filipov, J. M. LaFave, J. F. Hajjar, and D. A. Foutch. 2013. “Shear and friction response of nonseismic laminated elastomeric bridge bearings subject to seismic demands.” J. Bridge Eng. 18 (7): 612–623. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000406.
Tobias, D. H., R. E. Anderson, C. E. Hodel, W. M. Kramer, R. M. Wahab, and R. J. Chaput. 2008. “Overview of earthquake resisting system design and retrofit strategy for bridges in Illinois.” Pract. Period. Struct. Des. Constr. 13 (3): 147–158. https://doi.org/10.1061/(ASCE)1084-0680(2008)13:3(147).
Tsai, K. C., H. W. Chen, C. P. Hong, and Y. F. Su. 1993. “Design of steel triangular plate energy absorbers for seismic-resistant construction.” Earthq. Spectra 9 (3): 505–528. https://doi.org/10.1193/1.1585727.
Tsopelas, P., M. C. Constantinou, Y. S. Kim, and S. Okamoto. 1996. “Experimental study of FPS system in bridge seismic isolation.” Earthquake Eng. Struct. Dyn. 25 (1): 65–78. https://doi.org/10.1002/(SICI)1096-9845(199601)25:1%3C65::AID-EQE536%3E3.0.CO;2-A.
Tubaldi, E., S. A. Mitoulis, H. Ahmadi, and A. Muhr. 2016. “A parametric study on the axial behaviour of elastomeric isolators in multi-span bridges subjected to horizontal seismic excitations.” Bull. Earthquake Eng. 14 (4): 1285–1310. https://doi.org/10.1007/s10518-016-9876-9.
Wen, Y. K. 1976. “Method for random vibration of hysteretic systems.” J. Eng. Mech. Div. 102 (2): 249–263.
Whittaker, A. S., V. V. Bertero, C. L. Thompson, and L. J. Alonso. 1991. “Seismic testing of steel plate energy dissipation devices.” Earthq. Spectra 7 (4): 563–604. https://doi.org/10.1193/1.1585644.
Xiang, N., M. S. Alam, and J. Li. 2018. “Shake table studies of a highway bridge model by allowing the sliding of laminated-rubber bearings with and without restraining devices.” Eng. Struct. 171: 583–601. https://doi.org/10.1016/j.engstruct.2018.05.121.
Xiang, N., and J. Li. 2016. “Seismic performance of highway bridges with different transverse unseating-prevention devices.” J. Bridge Eng. 21 (9): 04016045. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000909.
Xiang, N., and J. Li. 2017. “Experimental and numerical study on seismic sliding mechanism of laminated-rubber bearings.” Eng. Struct. 141: 159–174. https://doi.org/10.1016/j.engstruct.2017.03.032.
Xiang, N., and J. Li. 2018. “Effect of exterior concrete shear keys on the seismic performance of laminated rubber bearing-supported highway bridges in China.” Soil Dynam. Earthq. Eng. 112: 185–197. https://doi.org/10.1016/j.soildyn.2018.04.033.
Xu, Y., R. Wang, and J. Li. 2016. “Experimental verification of a cable-stayed bridge model using passive energy dissipation devices.” J. Bridge Eng. 21 (12): 04016092. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000966.
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: Jan 23, 2019
Accepted: May 22, 2019
Published online: Sep 3, 2019
Published in print: Nov 1, 2019
Discussion open until: Feb 3, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.