Tensile Behavior and Cost-Efficiency Evaluation of ASTM A1010 Steel for Bridge Construction
Publication: Journal of Bridge Engineering
Volume 24, Issue 8
Abstract
This study investigates the mechanical properties of ASTM A1010 steel plates and assesses their cost efficiency through life cycle cost (LCC) analyses when used in bridge construction. First, tensile tests were conducted on specimens with different plate thicknesses and rolling direction orientations. The overall stress–strain response and tensile properties of the A1010 steel were evaluated. In addition, failure zones of fractured specimens were analyzed using a scanning electron microscope to reveal the fracture morphology and failure type. Then, to assess the competitiveness of this relatively new steel in bridge construction, a series of LCC analyses were conducted. The first analytical investigation focused on the comparative LCC performance of two case study bridges located at different atmospheric environments and constructed using either A1010 steel or painted conventional carbon steel. The second analytical study explored the major factors impacting the A1010 payoff time. Results indicated that the use of A1010 steel can be most beneficial in bridges located in aggressive environmental conditions with heavy traffic volumes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The work presented here was supported by the Virginia Transportation Research Council, but the views expressed herein are those of the authors. The authors thank Dr. Justin Ocel from the FHWA for his help in conducting the tensile tests. The assistance of Richard White at the Nanoscale Materials Characterization Facility at the University of Virginia during the SEM imaging is also gratefully acknowledged.
References
Albrecht, P., and T. T. Hall, Jr. 2003. “Atmospheric corrosion resistance of structural steels.” J. Mater. Civ. Eng. 15 (1): 2–24. https://doi.org/10.1061/(ASCE)0899-1561(2003)15:1(2).
ASTM. 2013. Standard specification for higher-strength martensitic stainless steel plate, sheet, and strip. ASTM A1010/A1010M-13. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard guide for estimating the atmospheric corrosion resistance of low-alloy steels. ASTM G101-04. West Conshohocken, PA: ASTM.
ASTM. 2016a. Standard specification for structural steel for bridges. ASTM A709/A709M-16a. West Conshohocken, PA: ASTM.
ASTM. 2016b. Standard test methods for tension testing of metallic materials. ASTM E8/E8M-16a. West Conshohocken, PA: ASTM.
ASTM. 2018. Standard specification for high-strength low-alloy Columbium-Vanadium structural steel. ASTM A572/A572M. West Conshohocken, PA: ASTM.
Baddoo, N. R. 2008. “Stainless steel in construction: A review of research, applications, challenges and opportunities.” J. Constr. Steel Res. 64 (11): 1199–1206. https://doi.org/10.1016/j.jcsr.2008.07.011.
Chen, Y. Y., H. J. Tzeng, L. I. Wei, L. H. Wang, J. C. Oung, and H. C. Shih. 2005. “Corrosion resistance and mechanical properties of low-alloy steels under atmospheric conditions.” Corros. Sci. 47 (4): 1001–1021. https://doi.org/10.1016/j.corsci.2004.04.009.
Coomarasamy, A., D. Lai, S. Ramamurthy, M. J. Walzak, B. Kobe, and J. A. Sawicki. 2010. “Effect of low alloy steel powder-ethyl silicate based coatings on corrosion behaviour of weathering steel exposed to salt environment.” In Proc., Corrosion 2010. Houston: NACE International.
Crampton, D. D., and K. P. Holloway. 2015. “Inspection and maintenance of weathering steel bridges.” In Proc., Structures Congress 2015, 379–391. Reston, VA: ASCE.
Das, A., and S. Tarafder. 2009. “Experimental investigation on martensitic transformation and fracture morphologies of austenitic stainless steel.” Int. J. Plast. 25 (11): 2222–2247. https://doi.org/10.1016/j.ijplas.2009.03.003.
Doyle, A., and B. Rabun. 2013. Bridge structures maintenance program. Georgia DOT Rep. Atlanta: Georgia DOT.
Fletcher, F. B. 2011. Improved corrosion-resistant steel for highway bridge construction. FHWA-HRT-11-062. Washington, DC: Federal Highway Administration.
Fletcher, F. B., H. E. Townsend, and A. D. Wilson. 2003. “Corrosion performance of improved weathering steels for bridges.” In World Steel Bridge Symp. Chicago: National Steel Bridge Alliance.
Fletcher, F., A. Wilson, J. Starsky, J. Kilpatrick, L. Mlcoch, and J. Wrysinski. 2005. “Stainless steel for accelerated bridge construction.” In Proc., FHWA Accelerated Bridge Construction Conf. Washington, DC: Federal Highway Administration.
Gallivan, F., J. Ang-Olson, A. Papson, and M. Venner. 2010. Greenhouse gas mitigation measures for transportation construction, maintenance, and operations activities. Washington, DC: AASHTO Standing Committee on the Environment.
Gedge, G. 2008. “Structural uses of stainless steel—Buildings and civil engineering.” J. Constr. Steel Res. 64 (11): 1194–1198. https://doi.org/10.1016/j.jcsr.2008.05.006.
Gooch, T., and B. Ginn. 1990. “Heat-affected zone toughness of SMA welded 12% Cr martensitic-ferritic steels.” Weld. J. 69 (11): 431–440 s.
Gross, J. H., R. D. Stout, D. C. Cook, J. E. Roberts, K. E. Arico, and M. B. Conrad. 2010. Improved corrosion-resistant steel for highway bridge construction. ATLSS Rep. 10–11. Bethlehem, PA: ATLSS Engineering Research Center.
Helsel, J. L., R. L. Lanterman, and K. L. Wissmar. 2008. “Expected service life and cost considerations for maintenance and new construction protective coating work.” In Corrosion 2008. Houston: NACE International.
ISO (International Organization for Standardization). 2012. Corrosion of metals and alloys-corrosivity of atmospheres-classification, determination and estimation. ISO 9923. Geneva: International Organization for Standardization.
Kallias, A. N., B. Imam, and M. K. Chryssanthopoulos. 2017. “Performance profiles of metallic bridges subject to coating degradation and atmospheric corrosion.” Struct. Infrastruct. Eng. 13 (4): 440–453. https://doi.org/10.1080/15732479.2016.1164726.
Kendall, A., G. A. Keoleian, and G. E. Helfand. 2008. “Integrated life-cycle assessment and life-cycle cost analysis model for concrete bridge deck applications.” J. Infrastruct. Syst. 14 (3): 214–222. https://doi.org/10.1061/(ASCE)1076-0342(2008)14:3(214).
Kere, K. J., and Q. Huang. 2019. “Life-cycle cost comparison of corrosion management strategies for steel bridges.” J. Bridge Eng. 24 (4): 04019007. https://doi.org/10.1061/(ASCE)BE.1943-5592.0001361.
McConnell, J., H. W. Shenton, III, D. R. Mertz, and D. Kaur. 2014. “National review on use and performance of uncoated weathering steel highway bridges.” J. Bridge Eng. 19 (5): 04014009. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000580.
Morcillo, M., B. Chico, I. Díaz, H. Cano, and D. De la Fuente. 2013. “Atmospheric corrosion data of weathering steels. A review.” Corros. Sci. 77 (Dec): 6–24. https://doi.org/10.1016/j.corsci.2013.08.021.
Okasha, N. M., D. M. Frangopol, F. B. Fletcher, and A. D. Wilson. 2012. “Life-cycle cost analyses of a new steel for bridges.” J. Bridge Eng. 17 (1): 168–172. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000219.
Saliba, N., and L. Gardner. 2013. “Experimental study of the shear response of lean duplex stainless steel plate girders.” Eng. Struct. 46 (Jan): 375–391. https://doi.org/10.1016/j.engstruct.2012.07.029.
San Marchi, C., B. P. Somerday, X. Tang, and G. H. Schiroky. 2008. “Effects of alloy composition and strain hardening on tensile fracture of hydrogen-precharged type 316 stainless steels.” Int. J. Hydrogen Energy 33 (2): 889–904. https://doi.org/10.1016/j.ijhydene.2007.10.046.
Sato, Y. S., T. W. Nelson, C. J. Sterling, R. J. Steel, and C. O. Pettersson. 2005. “Microstructure and mechanical properties of friction stir welded SAF 2507 super duplex stainless steel.” Mater. Sci. Eng.: A 397 (1–2): 376–384. https://doi.org/10.1016/j.msea.2005.02.054.
Seradj, H. 2010. “Weldability of ASTM A1010 steel.” In Proc., 8th Int. Conf. on Short and Medium Span Bridge. Montreal, QC, Canada: Canadian Society for Civil Engineering.
Seradj, H. 2015. “Oregon’s experience with ASTM A1010.” In Proc., Transportation Research Board 94th Annual Meeting, 15-3926. Washington, DC: The National Academies of Sciences, Engineering, and Medicine.
Sharp, S. R., B. M. Donaldson, J. L. Milton, and C. W. Fleming. 2013. Preliminary assessment of procedures for coating steel components on Virginia bridges. FHWA/VCTIR 14-R1. Charlottesville, VA: Virginia Center for Transportation Innovation and Research.
Soliman, M., and D. M. Frangopol. 2015. “Life-cycle cost evaluation of conventional and corrosion-resistant steel for bridges.” J. Bridge Eng. 20 (1): 06014005. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000647.
Taban, E., E. Deleu, A. Dhooge, and E. Kaluc. 2009. “Laser welding of modified 12% Cr stainless steel: Strength, fatigue, toughness, microstructure and corrosion properties.” Mater. Des. 30 (4): 1193–1200. https://doi.org/10.1016/j.matdes.2008.06.030.
Virmani, P. 2009. Improved corrosion-resistant steel for highway bridge construction: Knowledge-based design. FHWA-HRT-09-053. Washington, DC: The Federal Highway Administration.
Wilson, A. 2005. “Improvements to high performance steels.” In Proc., Int. Symp. on Microalloyed Steels. Materials Park, OH: ASM International.
Zhang, C., D. Cai, B. Liao, T. Zhao, and Y. Fan. 2004. “A study on the dual-phase treatment of weathering steel 09CuPCrNi.” Mater. Lett. 58 (9): 1524–1529. https://doi.org/10.1016/j.matlet.2003.10.018.
Information & Authors
Information
Published In
Copyright
© 2019 American Society of Civil Engineers.
History
Received: May 9, 2018
Accepted: Mar 7, 2019
Published online: May 20, 2019
Published in print: Aug 1, 2019
Discussion open until: Oct 20, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.