Structural Health Monitoring and Model Updating of Aizhai Suspension Bridge
Publication: Journal of Aerospace Engineering
Volume 30, Issue 2
Abstract
A complete structural health monitoring system has been implemented on Aizhai Suspension Bridge for monitoring its health status and assessing its safety for long-term services. This system consists of nearly 112 sensors of various types, including four subsystems: automatic data collection subsystem, artificial maintenance management subsystem, early safety warning and comprehensive assessment subsystem, and centralized database management subsystem. The deployments and functions of this structural health monitoring system are first introduced in this paper. Then, a finite-element model updating method, which combines the substructure method with the response surface model updating method, is proposed to reconstruct the actual working state of this suspension bridge in the early safety warning and comprehensive assessment subsystem. In the remaining part, the temperature fields, strain responses, tension forces of the hangers, longitudinal displacements of the stiffening girder, and the meteorological temperature are analyzed. Through the statistical analysis, the relationship between the temperature fields was found; the temperature fields induced strains of the stiffening girder satisfies the linear relationship. The cumulative probability distribution function of the cycle-index of the same daily stress amplitude follows a Weibull distribution. The monitored relative longitudinal displacements of the stiffening girder are linearly related with the meteorological temperatures. The monitored tension forces of the hangers verify the effects of the suspender-free zones of main cables on the normal hangers for this pylon-girder detached suspension bridge.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are grateful for the financial support from the Ministry of Science and Technology under the Grant Nos. 2011BAK02B01 and 2013CB036305.
References
Andersen, E. Y., and Pedersen, L. (1994). “Structural monitoring of the great belt east bridge.” Proc., 3th Symp. on Stait Crossing, J. Krokebogr, ed., Vol. 94, Balkema, Rotterdam, Netherlands, 189–195.
ANSYS 12.0 [Computer software]. ANSYS, Canonsburg, PA.
Baruch, M. (1982). “Optimal correction of mass stiffness matrix using measured modes.” AIAA J., 20(11), 1623–1626.
Berman, A. (1979). “Mass matrix correction using an incomplete set of measured models.” AIAA J., 17(10), 1147–1148.
Brownjohn, J. M. W., Bocciolone, M., Curami, A., Falco, M., and Zasso, A. (1994). “Humber bridge full-scale measurement campaigns 1990–1991.” J. Wind Eng. Ind. Aerodyn., 52, 185–218.
Brownjohn, J. M. W., Dumanoglu, A. A., and Severn, R. T. (1992). “Ambient vibration survey of the Faith Sultan Mehmet (Second Bosporus) Suspension Bridge.” Earthquake Eng. Struct. Dyn., 21(10), 907–924.
Cross, E. J., Koo, K. Y., Brownjohn, J. M. W., and Worden, K. (2013). “Long-term monitoring and data analysis of the Tamar Bridge.” Mech. Syst. Signal Process, 35(1–2), 16–34.
Deng, L., and Cai, C. S. (2010). “Bridge model updating using response surface method and genetic algorithm.” J. Bridge Eng., 553–564.
Diaferio, M., Foti, D., and Giannoccaro, N. I. (2015). “Identification of the modal properties of a squat historic tower for the tuning of a FE model.” Proc., 6th Int. Operational Modal Analysis Conf., Curran Associates, Red Hook, NY, 84–85.
Downing, S. D., and Socie, D. F. (1982). “Simple rainflow counting algorithms.” Int. J. Fatigue, 4(1), 31–40.
Duan, Y. F., Li, Y., and Xiang, Y. Q. (2011). “Strain-temperature correlation analysis of a tied arch bridge using monitoring data.” Proc., 2nd Int. Conf. on Multimedia Technology (ICMT), IEEE, Piscataway, NJ, 6025–6028.
Fang, K. T. (1980). “The uniform design: Application of number-theoretic methods in experimental design.” Acta Math. Appl. Sinica, 3(4), 363–372.
Fang, S. E., and Perera, R. (2011). “Damage identification by response surface based model updating using D-optimal design.” Mech. Syst. Signal Process, 25(2), 717–733.
Foti, D. (2013). “Dynamic identification techniques to numerically detect the structural damage.” Open Constr. Build. Tech. J., 7, 43–50.
Franke, R. (1982). “Scattered data interpolation: Test of some methods.” Math. Comput., 38(157), 181–200.
Horta, L. G., et al. (2010). “Finite element model calibration approach for Ares IX.” Proc., IMAC 28th, Springer, New York, 1037–1054.
Hu, J. H., and Shen, R. L. (2014). “Technical innovations of the Aizhai Bridge in China.” J. Bridge Eng., 04014028.
Jaishi, B., and Ren, W. (2005). “Structural finite element model updating using ambient vibration test results.” J. Struct. Eng., 617–628.
Kammer, D. C. (1991). “Sensor placement for on orbit modal identification and correlation of large space structures.” J. Guid. Control Dyn., 14(2), 251–259.
Kammer, D. C. (1992a). “Effect of model error on sensor placement for on-orbit modal identification of large space structures.” J. Guid. Control Dyn., 15(2), 334–341.
Kammer, D. C. (1992b). “Effects of noise on sensor placement for on-orbit modal identification of large space structures.” J. Dyn. Syst. Meas. Control, 114(3), 436–443.
Katsuchi, H., Yamada, H., and Kusuhara, S. (2008). “Structural monitoring and design verification of Akashi Kaikyo Bridge.” Proc., 11th Int. Conf. on Engineering, Science, Construction, and Operations in Challenging Environments, ASCE, Reston, VA, 1–8.
Ko, J. M., and Ni, Y. Q. (2005). “Technology developments in structural health monitoring of large-scale bridges.” Eng. Struct., 27(12), 1715–1725.
Koh, C., and Shankar, K. (2003). “Substructural identification method without interface measurement.” J. Eng. Mech., 769–776.
Kwong, H. S., Lau, C. K., and Wong, K. Y. (1995). “Monitoring system for Tsing Ma Bridge.” Proc., 13th Structures Congress, Vol. 1, ASCE, New York, 264–267.
Li, A. Q., et al. (2003). “Health monitoring system for the Runyang Yangtse River Bridge.” J. Southeast Univ., 33(5), 544–548 (in Chinese).
Li, S. L., Li, H., Ou, J. P., and Li, H. W. (2009). “Integrity strain response analysis of a long span cable-stayed bridge.” Key Eng. Mater., 413–414, 775–783.
Li, Z. J., Li, A. Q., and Han, X. L. (2010). “Dynamic analysis and experimental study of variations of the dynamic parameters of Runyang Suspension Bridge.” China Civ. Eng. J., 43(4), 92–98 (in Chinese).
Link, M. (1999). “Updating of analytical models—Review of numerical procedures and application aspects.” Proc., Structural Dynamics Forum SD2000, D. J. Ewins and D. J. Inman, eds., Research Studies Press, Baldock, U.K., 193–223.
Liu, X. Y., Cai, J., and Liu, H. (2002). Bridge damage detection, China Communications Press, Beijing.
Marwala, T. (2010). Finite element model updating using computational intelligence techniques: Applications to structural dynamics, Springer, London.
Meo, M., and Zumpano, G. (2005). “On the optimal sensor placement techniques for a bridge structure.” Eng. Struct., 27(10), 1488–1497.
Montgomery, D. C. (1997). Design and analysis of experiments, Wiley, New York.
Mottershead, J. E., and Friswell, M. I. (1993), “Model updating in structural dynamics: A survey.” J. Sound Vib., 167(2), 347–375.
Ou, J. P. (2003). “Some recent advances of intelligent health monitoring systems for civil infrastructures in mainland China.” Proc., 1st Int. Conf. on Structural Health Monitoring and Intelligent Infrastructure, Z. S. Wu and M. Abe, eds., Vol. 1, Balkema, Rotterdam, Netherlands, 131–144.
Ou, J. P., and Li, H. (2010). “Structural health monitoring in mainland China—Review and future trends.” Struct. Health Monit., 9(3), 219–231.
Peeters, B., and Roeck, G. D. (2001). “One-year monitoring of the Z24-Bridge: Environmental effects versus damage events.” Earthquake Eng. Struct. Dyn., 30, 149–171.
Pines, D., and Aktan, A. E. (2002). “Status of structural health monitoring of long span bridges in the United States.” Prog. Struct. Eng. Mater., 4(4), 372–380.
Putha, R., Quadrifoglio, L., and Zechman, E. (2012). “Comparing ant colony optimization and genetic algorithm approaches for solving traffic signal coordination under oversaturation conditions.” J. Comput. Aided Civ. Inf., 27(1), 14–28.
Roberts, G. W., Brown, C. J., Meng, X., Ogundipe, O., Atkins, C., and Colford, B. (2012). “Deflection and frequency monitoring of the Forth Road Bridge, Scotland, by GPS.” Proc. Inst. Civ. Eng. Bridge Eng., 165(2), 105–123.
Rowden, C., and Hall, S. (1992). Speech processing, McGraw-Hill, New York.
Sgambi, L., Gkoumas, K., and Bontempi, F. (2012). “Genetic algorithms for the dependability assurance in the design of a long span suspension bridge.” J. Comput. Aided Civ. Inf., 27(9), 655–675.
Wang, G. X., Ding, Y. L., Sun, P., Wu, L. L., and Yue, Q. (2015). “Assessing static performance of the Dashengguan Yangtze Bridge by monitoring the correlation between temperature field and its static strains.” Math. Probl. Eng., 2015, 12.
Wang, Y. Y. (1999). Theory and application of dynamic substructure method, Science Press, Beijing.
Yun, C. B., and Lee, H. J. (1997). “Substructural identification for damage estimation of structures.” Struct. Saf., 19(1), 121–140.
Zhou, L. R., Yan, G. R., and Ou, J. P. (2013). “Response surface method based on radial basis functions for modeling large-scale structures in model updating.” Comput. Aided Civ. Inf., 28(3), 210–226.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Feb 27, 2015
Accepted: Apr 12, 2016
Published online: Jul 12, 2016
Discussion open until: Dec 12, 2016
Published in print: Mar 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.