Moment Capacities and Deflection Limits of PFRP Sheet Piles
Publication: Journal of Composites for Construction
Volume 10, Issue 6
Abstract
The structural response of pultruded fiber-reinforced polymer (PFRP) sheet pile panels subjected to a uniform pressure load was investigated. Single, connected, and concrete-backfilled panels were tested to ultimate failure in an attempt to determine their moment capacities, deflection limits, and failure mechanisms. The load-carrying capacity of single-panel FRP piles was found to be 15% higher than that of three panels connected together. No pin and eye joint separation was observed at failure. The concrete backfilled hybrid panels exhibited significantly increased moment capacity. However, the increase in stiffness after the first concrete crack was, at best, only 76% over the pile without backfill. Bearing failure of a PFRP pile with a partially confined support created excessive deflection in the wall, but showed no significant reduction in the load capacity. On the other hand, with fully confined support, the ultimate failure of single, connected, and concrete-backfilled panels was dominated by local buckling, longitudinal tearing, and bearing crush at shear keys, upon reaching a deflection limit of span/50.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers gratefully acknowledge the continued support from Natural Science and Engineering Research Council (NSERC) of Canada and IBP Corporation of Alberta, Canada.
References
Bank, L. C., and Yin, J. (1999). “Failure of web-flange junction in postbuckled pultruded I-beams.” J. Compos. Constr., 3(4), 177–184.
Barbero, E. J., Fu, S. H., and Raftoyiannis, I. (1991). “Ultimate pending strength of composite beams.” J. Mater. Civ. Eng., 3(4), 292–306.
Giroux, C. (2000). “Analysis of the flexural behavior of a fiberglass composite seawall.” MS thesis, Dept. of Civil Engineering and Applied Mechanics, McGill Univ., Montreal, Quebec, Canada.
Giroux, C., and Shao, Y. (2003). “Flexural and shear rigidity of composite sheet piles.” J. Compos. Constr., 7(4), 348–355.
Linzell, D. G., and Boothby, T. E. (2004). “Flexural strength of FRP sheet piling panels under simulated surface loads.” Proc., Advanced Composite Materials in Bridges and Structures (ACMBS IV) (CD-ROM).
Mottram, J. T. (2004). “Determination of critical load for flange buckling in concentrically loaded pultruded columns.” Composites, Part B, 35(1), 35–47.
Nagaraj, V., and GangaRao, H. V. S. (1997). “Static behavior of pultruded GFRP beams.” J. Compos. Constr., 1(3), 120–129.
Qiao, P., Davalos, J. F., and Wang, J. (2001). “Local buckling of composite FRP shapes by discrete plate analysis.” J. Struct. Eng., 127(3), 245–255.
Shanmugam, J. (2004). “Moment capacity and deflection behavior of pultruded FRP composite sheet piles.” MS thesis, Dept. of Civil Engineering and Applied Mechanics, McGill Univ., Montreal, Quebec.
Shao, Y., and Kouadio, S. (2002). “Durability of fiberglass composite sheet piles in water.” J. Compos. Constr., 6(4), 280–287.
Shao, Y., and Shanmugam, J. (2004). “Deflection creep of pultruded composite sheet piling.” J. Compos. Constr., 8(5), 471–479.
Sims, G. D., Johnson, A. F., and Hill, R. D. (1987). “Mechanical and structural properties of a GRP pultruded section.” Compos. Struct., 8, 173–187.
Timoshenko, S. (1955). Strength of materials, Litton Educational, New York.
Information & Authors
Information
Published In
Copyright
© 2006 American Society of Civil Engineers.
History
Received: Sep 21, 2004
Accepted: Mar 14, 2006
Published online: Dec 1, 2006
Published in print: Dec 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.