Reinforced Concrete T-Beams Strengthened in Shear with Fiber Reinforced Polymer Sheets
Publication: Journal of Composites for Construction
Volume 7, Issue 4
Abstract
This research studies the interaction of concrete, steel stirrups, and external fiber reinforced polymer (FRP) sheets in carrying shear loads in reinforced concrete beams. A total of eight tests were conducted on four laboratory-controlled concrete T-beams. The beams were subjected to a four-point loading. Each end of each beam was tested separately. Three types of FRP, uniaxial glass fiber, uniaxial carbon fiber, and triaxial glass fiber, were applied externally to strengthen the web of the T-beams, while some ends were left without FRP. The test results show that FRP reinforcement increases the maximum shear strengths between 15.4 and 42.2% over beams with no FRP. The magnitude of the increased shear capacity is dependent not only on the type of FRP but also on the amount of internal shear reinforcement. The triaxial glass fiber reinforced beam exhibited more ductile failure than the other FRP reinforced beams. This paper also presents a test model that is based on a rational mechanism and can predict the experimental results with excellent accuracy.
Get full access to this article
View all available purchase options and get full access to this article.
References
Alexander, J., and Cheng, J. J. R. (1996). “Field application and studies of using CFRP sheets to strengthen concrete bridge girders.” Proc., 2nd Int. Conf. in Advanced Composite Materials in Bridges and Structures, Canadian Society for Civil Engineering, Montreal, 465–472.
Alexander, J., and Cheng, J. J. R. (1997). “Shear rehabilitation of G-girder bridges using CFRP sheets.” Structural Engineering Rep. No. 218, Dept. of Civil and Environmental Engineering, Univ. of Alberta, Edmonton, Alta., Canada.
Alexander, J., and Cheng, J. J. R. (1998). “Shear design model of concrete girders strengthened with advanced composite materials.” Proc., 5th Int. Conf. in short and medium span bridges, Canadian Society for Civil Engineering, Montreal.
Al-Sulaimani, G. J., Istem, A., Basunbul, A. S., Baluch, M. H., and Ghaleb, B. N.(1994). “Shear repair for reinforced concrete by fiberglass plate bonding.” Am. Concr. Inst. Struct. J.,91(3), 458–464.
American Association of State Highway Transportation Officials (AASHTO). (1994). Standard specifications for highway bridges, 14th Ed., Washington, D.C.
American Concrete Institute (ACI). (1995). “Building code requirements for structural concrete.” 318-95, Detroit.
ASTM. (1995). “Standard test methods for tensile properties of polymer matrix composite materials.” D 3039M, West Conshohocken, Pa.
Bizindavyi, L., and Neale, K. W.(1999). “Transfer lengths and bond strengths for composites bonded to concrete.” J. Compos. Constr., 3(4), 153–160.
Brosens, K., and Van Gemert, D. (1999). “Anchorage design for externally bonded carbon fiber reinforced polymer lamintes.” Proc., 4th Int. Symp. on Fiber Reinforced Polymer Reinforcement for Reinforced Concrete Structures, American Concrete Institute, Detroit, 635–645.
Canadian Standards Association (CSA). (1988). “Design of highway bridges.” S6, Rexdale, Ontario.
Canadian Standards Association (CSA). (1994). “Design of concrete structures.” A23.3, Rexdale, Ontario.
Chajes, M. J., Finch, W. W., Januszka, T. F., and Thomson, T. A.(1996). “Bond and force transfer of composite material plates bonded to concrete.” ACI Struct. J., 93(3), 208–217.
Chajes, M. J., Januszka, T. F., Mertz, D. R., Thomson, T. A., and Finch, W. W.(1995). “Shear strengthening of reinforced concrete beams using externally applied composite fabrics.” Am. Concr. Inst. Struct. J.,92, 295–303.
Collins, M. P., and Mitchell, D. (1987). Prestressed concrete basics, 1st Ed., Canadian Prestressed Concrete Institute, Ottawa.
Deniaud, C., and Cheng, J. J. R. (1998). “Shear rehabilitation of type G-girders using ACM: Experimental study.” Proc., 5th Conf. on Short and Medium Span Bridges, Canadian Society for Civil Engineering, Calgary, Alta., Canada.
Deniaud, C., and Cheng, J. J. R. (2000). “Evaluation of shear design methods of reinforced concrete beams strengthened with FRP sheets.” Proc., 3rd Int. Conf. on Advanced Composite Materials in Bridges and Structures, Canadian Society for Civil Engineering, Ottawa.
Drimoussis, E. H., and Cheng, J. J. R. (1994). “Shear strengthening of concrete girders using carbon fiber reinforced plastic sheets.” Structural Engineering Rep. No. 205, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alta., Canada.
Jones, R., Swamy, R. N., and Charif, A.(1988). “Plate separation and anchorage of reinforced concrete beams strengthened by epoxy-bonded steel plates.” Struct. Eng., 66, 85–94.
Loov, R.(1998). “Review of A23.3-94 simplified method of shear design and comparison with results using shear friction.” Can. J. Civ. Eng., 25, 437–450.
Ritchie, P. A., Thomas, D. A., Lu, L. W., and Connelly, G. M.(1991). “External reinforcement of concrete beams using fiber reinforced plastics.” Am. Concr. Inst. Struct. J.,88 (4), 490–500.
Swamy, R. N., Jones, R., and Bloxham, J. W.(1987). “Structural behaviour of reinforced concrete beams strengthened by epoxy-bonded steel.” Struct. Eng., 65A, 59–68.
Triantafillou, T. C.(1998). “Shear strengthening of reinforced concrete beams using epoxy-bonded FRP composites.” Am. Concr. Inst. Struct. J.,95(2), 107–115.
Information & Authors
Information
Published In
Copyright
Copyright © 2003 American Society of Civil Engineers.
History
Received: Jul 12, 1999
Accepted: Oct 21, 2002
Published online: Oct 15, 2003
Published in print: Nov 2003
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.