Calibration of Soil Constitutive Models with Spatially Varying Parameters
Publication: Journal of Geotechnical and Geoenvironmental Engineering
Volume 133, Issue 12
Abstract
Soil constitutive models are frequently calibrated from laboratory tests that utilize global boundary measurements, which necessarily relegate soil response to that of a homogenized equivalent medium. This paper demonstrates the applicability of advanced experimental technologies to enhance the state of model-based predictions in soil mechanics by taking into account the possibility of material heterogeneity during model calibration. By utilizing the full-field displacement measurement technique of three-dimensional digital image correlation, displacements of the surfaces of deforming triaxial sand specimens are measured throughout deformation. These displacements are assimilated into finite-element (FE) models of the test specimen through solution of an inverse problem. During optimization, in which the difference between measured and predicted displacements across the specimen surface form the basis for the objective function, model parameters are allowed to vary spatially throughout the specimen volume. FE models allowing three different levels of spatial variability are tested. Results indicate that accommodating consideration of material heterogeneity during calibration leads to more accurate predictions of global stress-strain behavior that are more faithful to observed full-field response.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This work was partially supported by National Science Foundation (NSF) Grant Nos. NSFCMS-0220309 and NSFCMS-0527828. The writers greatly appreciate this support.
References
Andrade, J. E., and Borja, R. I. (2006). “Capturing strain localization in dense sands with random density.” Int. J. Numer. Methods Eng., 67(11), 1531–1564.
Baxter, S. C., and Graham, L. L. (2000). “Characterization of random composites using moving-window technique.” J. Eng. Mech., 126(4), 389–397.
Baxter, S. C., Graham-Brady, L. L., and Xu, X. F. (2005). “Modeling the effects of material non-linearity using moving window micromechanics.” Int. J. Non-Linear Mech., 40, 351–359.
Bruck, H. A., McNeill, S. R., Sutton, M. A., and Peters, W. H., III. (1989). “Digital image correlation using Newton–Raphson method of partial differential corrections.” Exp. Mech., 29(3), 261–268.
Cho, G. C., Lee, J.-S., and Santamarina, J. C. (2004). “Spatial variability in soils: High resolution assessment with electrical needle probe.” J. Geotech. Geoenviron. Eng., 130(8), 843–850.
Finno, R. J., Harris, W. W., Mooney, M. A., and Viggiani, G. (1997). “Shear bands in plane strain compression of loose sand.” Geotechnique, 47(1), 149–165.
Gilbert, P. A., and Marcuson, W. F. (1988). “Density variation in specimens subjected to cyclic and monotonic loads.” J. Geotech. Engrg., 114(1), 1–20.
Goto, S., Tatsuoka, F., Shibuya, S., Kim, Y.-S., and Sato, T. (1991). “A simple gauge for local small strain measurements in the laboratory.” Soils Found., 31(1), 169–180.
Hallquist, J. O. (1998). : Theoretical manual, Livermore Software Technology Corporation, Livermore, Calif.
Helm, J. D., McNeill, S. R., and Sutton, M. A. (1996). “Improved 3D image correlation for surface displacement measurement.” Opt. Eng. (Bellingham), 35(7), 1911–1920.
Kuo, C.-Y., and Frost, J. D. (1996).“Uniformity evaluation of cohesionless specimens using digital image analysis.” J. Geotech. Engrg., 122(5), 390–396.
Ladd, R. S. (1978). “Preparing test specimens using undercompaction.” Geotech. Test. J., 1(1), 16–23.
Liang, L., Saada, A., Figueroa, J. L., and Cope, C. T. (1997). “The use of digital image processing in monitoring shear band development.” Geotech. Test. J., 20(3), 324–339.
Liu, S., and Chao, Y. J. (2005). “Determination of global mechanical response of friction stir welded plates using local constitutive properties.” Modell. Simul. Mater. Sci. Eng., 13, 1–15.
Mahnken, R., and Stein, E. (1997). “Parameter identification for finite deformation elasto-plasticity in principal directions.” Comput. Methods Appl. Mech. Eng., 147, 17–39.
McVeigh, C., Vernerey, F., Liu, W. K., and Brinson, L. C. (2006). “Multiresolution analysis for material design.” Comput. Methods Appl. Mech. Eng., in press.
Mulilis, J. P., Arulanandan, K., Chan, C. K., Seed, H. B., and Mitchell, J. K. (1977). “Effects of sample preparation on sand liquefaction.” J. Geotech. Engrg. Div., 103(2), 91–108.
Myers, R. H., and Montgomery, D. C. (1995). Response surface methodology: Process and product optimization using designed experiments, Wiley, New York.
Park, H. S., Karpov, E. G., Klein, P. A., and Liu, W. K. (2005). “Three-dimensional bridging scale analysis of dynamic fracture.” J. Comput. Phys., 207, 588–609.
Popescu, R., Deodatis, G., and Nobahar, A. (2005). “Effects of random heterogeneity of soil properties on bearing capacity.” Probab. Eng. Mech., 20, 324–341.
Rechenmacher, A. L. (2006). “Grain-scale processes governing shear band initiation and evolution in sands.” J. Mech. Phys. Solids, 54, 22–45.
Rechenmacher, A. L., and Finno, R. J. (2004). “Digital image correlation to evaluate shear banding in dilative sands.” Geotech. Test. J., 27(1), 13–22.
Schreier, H. W., Braasch, J. R., and Sutton, M. A. (2000). “Systematic errors in digital image correlation caused by intensity interpolation.” Opt. Eng. (Bellingham), 39(11), 2915–2921.
Schreier, H. W., Garcia, D., and Sutton, M. A. (2004). “Advances in light microscope stereo vision.” Exp. Mech., 44(3), 278–288.
Stander, N., Eggleston, T., Craig, K., and Roux, W. (2003). LS-OPT user’s manual: Design optimization software for the engineering analyst, Livermore Software Technology, Corp., Livermore, Calif.
Sutton, M. A., McNeill, S. R., Helm, J. D., and Chao, Y. J. (2000). “Advances in two-dimensional and three-dimensional computer vision.” Top. Appl. Phys., 77, 323–372.
Swoboda, G., Ichikawa, Y., Dong, Q., and Zaki, J. (1999). “Back analysis of large geotechnical models.” Int. J. Numer. Analyt. Meth. Geomech., 23, 1455–1472.
Triggs, B., McLauchlan, P., Hartley, R., and Fitzgibbon, A. (2000). “Bundle adjustment - A modern synthesis.” Vision algorithms: Theory and practice, W. Triggs, A. Zissermann, and R. Szeleski, eds., Springer, New York, 298–375.
Vaid, Y. P., Sivathayalan, S., and Stedman, D. (1999). “Influence of specimen-reconstituting method on the undrained response of sand.” Geotech. Test. J., 22(3), 187–195.
Zeghal, M., and Oskay, C. (2003). “A local identification technique for geotechnical and geophysical systems.” Int. J. Numer. Analyt. Meth. Geomech., 27, 967–987.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: May 1, 2006
Accepted: Apr 14, 2007
Published online: Dec 1, 2007
Published in print: Dec 2007
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.