Effect of Jordanian Oil Shale Fly Ash on Asphalt Mixes
Publication: Journal of Materials in Civil Engineering
Volume 17, Issue 5
Abstract
It is estimated that about of oil shale is available in the southern part of Jordan. Several studies are being carried out to utilize this source of energy efficiently. Upon direct combustion of this oil shale, more than 50% of its quantity will be left as fly ash. Resulting fly ash is considered undesirable and environmentally hazardous. This investigation was conducted to make use of the fly ash in the modification of local asphalt mixes. The modification efficiency was evaluated by the improvement in the performance of prepared asphalt concrete mixes. To carry out this study, enough quantity of oil shale was collected from Al-Lajjoun quarries (about south of Amman, Jordan). This material was then crushed, sieved, and burned to obtain the fly ash. Chemical and physical analyses of the fly ash were then performed. Asphalt concrete mixes having different percentages of fly ash (0, 10, 50, and 100%) as a replacement of the mineral filler, material passing the sieve, were prepared. These samples were characterized using the Marshall Stability, indirect tensile strength, stripping resistance, resilient modulus, dynamic creep, fatigue, and rutting tests. Test results were statistically analyzed and indicated that, in general, the addition of fly ash improved both strength, and water sensitivity of the asphalt concrete mixes. Replacing 10% of the mineral filler by fly ash proved to be the most effective percentage in improving the mechanical properties of all the prepared samples.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to acknowledge the support of the College of Graduate Studies and Scientific Research at Hashemite University for funding this research study. Thanks are extended to Eng. Mazen Al-Zou’bi, for his assistance during the experimental work.
References
Anani, B., and Al-Abdul Wahhab, H. (1982). “Effects of baghouse fines and mineral fillers on properties of asphalt pavements.” Transportation Research Board No. 843, Washington, D.C., 57–64.
Anderton, G. (1991). “Modified asphalt binders for military airfield pavements.” Proc., Aircraft/Pavement Interaction—An Integrated System, Kansas City, Mo., ASCE, Reston, Va., 170–190.
Assa’ad, A. (2003). “Oil shale direct combustion and the use of fly ash for the soil stabilization.” Dirasat, Jordan Univ., 30(1), 146–161.
Brown, E., McRae, J., and Crawley, A. (1989). “Effect of aggregates on performance of bituminous paving mixtures.” ASTM Special Technical Publication 1016, Pa.
Cominsky, R., Huber, G., Kennedy, T., and Anderson, M. (1994). “The superpave mix design manual for new construction and overlay.” Rep. No. SHRP-A-407, National Research Council, Washington, D.C.
Hamdan, M., and Azzam, S. (1999). “Direct combustion of oil shale using a circulating fluidized bed combustor.” Dirasat, Jordan Univ., 26(2), 174–181.
Hamdan, M., Khraish, Y., and Al-Dabbas, M. (1995). “Combustion of shale oil.” Proc., 1st Jordanian Mechanical Engineering Conf., Jordan Engineers Assoc., Amman, Jordan.
Jaber, J., and Probert, S. (2000). “Reaction kinetics of fluidised bed gasification of Jordanian oil shales.” Int. J. Therm. Sci., 39, 295–304.
Jaber, J., Probert, S., and Williams, P. (1999). “Evaluation of oil yield from Jordanian oil shales.” Energy J., 24(2), 761–781.
Kandhal, P., Lynn, C., and Parker, F. (1998). “Characterization tests for mineral fillers related to performance of asphalt paving mixtures.” NCAT Rep. No. 98-2, National Center for Asphalt Technology, Auburn, Ala.
Katamine, N. (2000). “Physical and mechanical properties of bituminous mixtures containing oil shales.” J. Transp. Eng., 126(2), 178–184.
Marcus, D., Sangrey, D., and Miller, S. (1985). “Effects of cementation process on spent shale stabilization.” Trans. Soc. Min. Eng. AIME, 278, 1225–1232.
Ministry of Energy and Mineral Resources (MEMR). (1999). Ann. Rep. of the Ministry, Amman, Jordan.
Montgomery, D. C. (1991). Design and analysis of experiments, 3rd Ed., Wiley, New York.
Mustafa, I., Bsieso, M., Bakri, W., Jebril, Z., and Anani, F. (1993). “Renewable energy in Jordan: Share in total energy-mix.” Rep. The Higher Council for Science and Technology, Amman, Jordan.
Richardson, W. (1914). The modern asphalt pavement, Wiley, New York.
StatSoft, Inc. (1997). STATISTICA for Windows [computer program manual], Tulsa, Okla.
Suliman, M., and Awwad, M. (2000). “The use of oil shale aggregates as a pavement material.” Internal Rep., Amman College for Engineering Technology and Al-Balqa Applied Univ., Jordan Engineers Assoc., Amman, Jordan.
Suliman, M., Awwad, M., and Shbeeb, L. (2004). “Heavy vehicles are damaging our highways.” Proc., Jordan Int. Conf. on Sustainable Development of Transportation Systems, Amman, Jordan.
Terrel, R., and Epps, J. (1989). “Using additives and modifiers in hot mix asphalt.” QI Series 114, National Asphalt Pavement Assoc., Md.
Tunnicliff, D. (1962). “A review of mineral filler.” Proc., AAPT, 31, 118–150.
Turner, J. (1994). “Soil stabilization using oil-shale solid waste.” J. Geotech. Eng., 120(4), 646–660.
Witczak, M., Schwartz, C., and Von Quintus, H. (2001). “NCHRP Project 9–19: Superpave support and performance models management.” Interim Rep., Federal Highway Administration and the National Cooperative Highway Research Program, Washington, D.C.
Information & Authors
Information
Published In
Copyright
© 2005 ASCE.
History
Received: Mar 23, 2004
Accepted: Dec 28, 2004
Published online: Oct 1, 2005
Published in print: Oct 2005
Notes
Note. Associate Editor: Louay N. Mohammad
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.