Interpretation of Accelerated Laboratory Testing of the Prototype Modulas Stress in Motion Sensor with the MMLS3 Load Simulator
Publication: Journal of Transportation Engineering
Volume 134, Issue 10
Abstract
With modern heavy vehicles using higher inflation pressures and higher axle loads the dynamic measurement of the tire-pavement contact force/stress is essential not only for tire development but also in road research for the investigation of factors which may lead to excessive damage of pavements. In this paper the results of laboratory tests with a prototype stress in motion (SIM) quartz sensor trafficked with a one-third scale load simulator (MMLS3) are presented. The tests were designed to vary parameters such as tire inflation pressure, speed, ambient temperature, lateral position, and angle to direction of travel in a controlled environment in order to isolate the influence of these parameters on the SIM sensor results. All other controllable variables remained constant while the target parameter was varied. Tire inflation pressures were calculated from these data. The laboratory tests show that the prototype sensor promises to be an effective investigative tool for SIM measurements.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to express their gratitude to the Swiss Commission for Technology and Innovation (CTI/KTI), Swiss Federal Roads Authority (FEDRO, ASTRA), Swiss Office for the Environment (FOEN/ BAFU) for the financial support of the project, Kistler Instruments AG, Switzerland for providing the sensors, and Mr. Simon Kuentzel of Empa for performing the laboratory tests.
References
De Beer, M. (2006). “Reconsideration of tyre-pavement input parameters for the structural design of flexible pavements.” Proc., 10th Int. Conf. on Asphalt Pavements, Quebec.
De Beer, M., Kannemeyer, L., and Fischer, C. (1999). “Towards improved mechanistic design of thin asphalt layer surfaces based on actual tyre/pavement contact stress-in-motion (SIM) data in South Africa.” Proc., 7th Conf. on Asphalt Pavements for Southern Africa, CAPSA ’99, Johannesburg.
Doupal, E., and Gysi, M. (2002). “Measurement of dynamic wheel load distributions.” Proc., NATMEC-ICWIM-3 Congress, Orlando, Fla.
Epps, A. L., Ahmed, T., Little, D., Mikhail, M. Y., and Hugo, F. (2001). “Performance assessment with the MMLS3 at the WesTrack.” Asph. Paving Technol. 70, 509–542.
European Cooperative Projects Eureka. (2001). Project Number E!2486, ⟨www.Eureka.be⟩.
Ford, T. L., and Yap, P. (1990). “Truck tire/pavement interface.” Proc. 23rd FISITA Congress, Technical Papers, Vol. II, Fisita, Torino, Italy.
Hugo, F. (2000). “Rutting performance of dustrol rehabilitation under TxMLS trafficking with increasing tire pressure.” Rep. No. 1814-4, Texas DOT, Austin, Tex.
Hugo, F., Epps, A. L., and Martin, F. (2004). “Significant findings from the full-scale accelerated pavement testing.” Synthesis 325, Transportation Research Board, National Research Council, Washington, D.C.
Kim, S. M., Hugo, F., and Roeset, J. M. (1998). “Small-scale accelerated pavement testing.” J. Transp. Eng., 124(2), 117–122.
Machemehl, R. B., Wang, F., and Prozzi, J. A. (2005). “Analytical study of effects of truck tire pressure on pavements using measured tire-pavement contact stress data.” Proc., Transportation Research Board Annual Meeting, Transportation Research Board, Washington, D.C.
“Measurement of wheel load distribution with MODULAS sensor type 9197.” (undated ). Kistler Catalogue, 53.609e-08.00, Switzerland.
Owende, M. O., Hartman, A. M., Ward, S. M., Gilchrist, M. D., and O’Mahony, M. J. (2001). “Minimizing distress on flexible pavements using variable tire pressure.” J. Transp. Eng., 127(3), 254–262.
Raab, C., Partl, M. N., Jenkins, K., and Hugo, F. (2005). “Determination of rutting and water susceptibility of selected pavement materials using MMLS3.” Proc. 7th Int. Conf. on the Bearing Capacity of Roads, Railways and Airfields, BCRA’05, BCRA, Trondheim, Norway.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: May 8, 2007
Accepted: Mar 3, 2008
Published online: Oct 1, 2008
Published in print: Oct 2008
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.