Transverse Pavement Grooving against Hydroplaning. II: Design
This article is a reply.
VIEW THE ORIGINAL ARTICLEThis article has a reply.
VIEW THE REPLYPublication: Journal of Transportation Engineering
Volume 132, Issue 6
Abstract
This paper analyzes the effect of groove dimensions (width, depth, and spacing) of transversely grooved pavement surface on hydroplaning using a three-dimensional finite-volume hydroplaning simulation model. Groove widths varying from 2 to 10 mm, groove depths from 1 to 10 mm, and center-to-center spacings from 5 to 25 mm are examined. The effectiveness of a pavement groove design against hydroplaning can be assessed by its ability to raise the hydroplaning speed, which is the vehicle speed at which hydroplaning occurs. It is found that the hydroplaning speed can be raised by increasing the groove depth and width, and decreasing the groove spacing, thereby reducing the risk of hydroplaning occurrence. Among the three groove dimensions (i.e., width, depth, and spacing), changes in groove width is found to have the most significant effect, followed by groove spacing and groove depth. This paper next proposes an analytical procedure for the design of transverse pavement grooving using the simulation model based on the concept of risks of hydroplaning. An illustration of the proposed design procedure is presented in this paper, using a wet-weather freeway vehicle speed distribution, to determine the transverse pavement grooving designs for different risk levels from 0.001% upward. The design concept also allows one to assess the hydroplaning risk level of an existing transversely grooved pavement surface or a proposed groove design, with known wet-weather traffic speed distribution and water film thickness.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Concrete Paving Association (ACPA). (2005). “Database of the state DOT concrete pavement practices—Tining dimensions.” ACPA, Washington, D.C., ⟨www.pavement.com⟩ (March 1, 2005).
Beaton, J. L., Zube, E., and Skog, J. (1969). “Reduction of accidents by pavement groovings.” Special Rep. No. 101, Highway Research Board, Washington, D.C., 110–125.
Blevins, R. D. (1984). Applied fluid dynamics handbook, Van Nostrand Reinhold, New York.
Chemical Rubber Company (CRC).(1988). Handbook of chemistry and physics, 69th Ed., CRC, Cleveland.
Grady, J. E., and Chamberlin, W. P. (1981) “Groove-depth requirements for tine-textured pavements.” Transportation Research Record 836, Transportation Research Board, Washington, D.C., 67–76.
Horne, W. B., and Dreher, R. C. (1963). “Phenomena of pneumatic tire hydroplaning.” NASA TN D-2056, National Aeronautics and Space Administration, Washington, D.C.
Horne, W. B., and Tanner, J. A. (1969). “Joint NASA–British Ministry of Technology skid correlation study: Results from American vehicles: Pavement grooving and traction studies.” NASA SP-5073, National Aeronautics and Space Administration, Washington, D.C., 325–360.
Kyte, M., Khatib, Z., Shannon, P., and Kitchener, F. (2001). “Effect of weather on free-flow speed.” Transportation Research Record 1776, Transportation Research Board, Washington, D.C., 60–68.
Leyder, J. P., and Reichert, J. (1974). “Techniques for achieving nonskid pavement surfaces by deep transverse grooving of fresh cement concrete.” Transportation Research Record 523, Transportation Research Board, Washington, D.C., 141–150.
Mosher, L. G. (1969). “Results from studies of highway grooving and texturing by several state highway departments: Pavement traction and grooving studies.” NASA SP-5073, National Aeronautics and Space Administration, Washington, D.C., 465–504.
Ong, G. P., and Fwa, T. F. (2006). “Transverse pavement grooving against hydroplaning. I: Simulation model.” J. Transp. Eng. 132 (6), 441–448.
Rugenstein, E. E. (1977). “Summary and evaluation of concrete pavement texturing practices.” Proc., Int. Conf. of Concrete Pavement Design, Purdue Univ., West Lafayette, Ind., 557–563.
Wu, C. L., and Nagi, M. A. (1995). “Optimizing surface texture of concrete pavement.” Research and Development Bulletin RD111T, Portland Cement Association, Skokie, Ill.
Yager, T. J. (1969). “Comparative braking performance of various aircraft on grooved and ungrooved pavements at the landing research runway, NASA Wallops Station: Pavement grooving and traction studies.” NASA SP-5073, National Aeronautics and Space Administration, Washington, D.C., 35–66.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: Mar 11, 2005
Accepted: Oct 25, 2005
Published online: Jun 1, 2006
Published in print: Jun 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.