Modeling of Pavement Response Using Nonlinear Cross-Anisotropy Approach
Publication: Journal of Transportation Engineering
Volume 132, Issue 6
Abstract
The multidepth deflectometer (MDD) is used to estimate flexible pavement response subjected to permitted overweight truck traffic (gross vehicle weight up to 556 kN). This study focuses on using material constitutive models to assess the most accurate and reliable pavement layer behavior. Deflections from MDDs installed on tested pavement section were compared with predicted ones using different material constitutive models to determine the best model. As a result, the best comparisons with the measured MDD deflections were achieved when base and subgrade materials were modeled as nonlinear cross anisotropic. In terms of pavement performance prediction, predicted rutting using a nonlinear cross-anisotropy model was matched reasonably well with measured values by generating a slightly higher compressive vertical strain from each subdivided layer. In addition, the cross-anisotropy characteristic of asphalt concrete material was introduced and applied to predict pavement performance. This results in larger rutting due to vertical strain within the asphaltic concrete layer. Thus, there is a need to take into account nonlinear cross-anisotropy characteristic of pavement materials in assessing pavement damage due to truck loadings.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to acknowledge the Texas Department of Transportation (TxDOT) for their support and cooporation. Also, gratitude goes to the Brownsville Port Office for providing traffic data.
References
Adu-Osei, A. (2000). “Characterization of unbound granular layers in flexible pavements.” Ph.D. dissertation, Texas A&M Univ., College Station, Tex.
Bellotti, R., Jamiolkowski, M., Lo Presti, D. C. F., and O’Neill, D. A. (1996). “Anisotropy of small strain stiffness in Ticino sand.” Geotechnique, 46(1), 115–131.
Brown, S. F. (1996). “Soil mechanics in pavement engineering.” Geotechnique, 46(3), 383–426.
Burmister, D. M. (1943). “Theory of stresses and displacements in layered systems and application to the design of airport runways.” Proc., Highway Research Board, Vol. 23, Highway Research Board, Washington, D.C, 126–148.
Chen, D. H., Bilyeu, J., and Hugo, F. (1999). “Monitoring pavement response and performance using in-situ instrumentation.” Field instrumentation for soil and rock: ASTM STP 1358, ASTM, Philadelphia, 1–7.
Fernando, E. G., and Liu, W. (1999). User’s manual for pavement dynamic backcalculation procedure with systems identification method (DBSID), Texas Transportaion Institute, Texas A&M Univ., College Station, Tex.
Gazetas, A. M. (1982). “Stresses and displacements in cross-anisotropic soils.” J. Geotech. Eng. Div., Am. Soc. Civ. Eng., 108(4), 532–553.
Hicks, R. G. (1970). “Factors influencing the resilient properties of granular materials.” Ph.D. thesis, Univ. of California at Berkeley, Berkeley, Calif.
Kenis, W. J. (1978). “Predictive design procedure.” VESYS user’s manual: An interim design method for flexible pavement using the VESYS structural subsystem.
Kirkpatric, W. M., and Rennie, I. A. (1972). “Directional properties of a consolidated Kaolinite.” Geotechnique, 22(1), 166–169.
Lytton, R. L. (2000). “Characterizing asphalt pavements for performance.” Transportation Research Record. 1723, Transportation Research Board, Washington, D.C., 5–16.
MODULUS user’s manual: Version 6.0 (MODULUS). (1992). Texas Transportaion Institute, Texas A&M Univ., College Station, Tex.
Raad, L., and Figueroa, J. L. (1980). “Load response of transportation support systems.” J. Transp. Eng., 106(1), 111–128.
Ramos, S. (2003). “Guidelines of pavement designs for dedicated overweight truck routes.” MSc thesis, Texas A&M Univ., College Station, Tex.
Tseng, K-H., and Lytton, R. L. (1989). “Prediction of permanent deformation in flexible pavement materials.” Implication of aggregates in the design, construction, and performance of flexible pavements: ASTM STP 1016, ASTM, Philadelphia, 154—172.
Tutumluer, E. (1995). “Prediction behavior of flexible pavements with granular bases.” Ph.D. thesis, Georgia Institute of Technology, Atlanta.
Tutumluer, E., and Thompson, M. R. (1997). “Anisotropic modeling of granular bases in flexible pavements.” Transportation Research Record. 1577, Transportation Research Board, Washington, D.C., 18–26.
Uzan, J. (1985). “Characterization of granular material.” Transportation Research Record. 1022, Transportation Research Board, Washington, D.C., 52–59.
Uzan, J. (1992). “Resilient characterization of pavement materials.” Int. J. Numer. Analyt. Meth. Geomech., 16, 453–459.
Ward, W. H., Samuels, S. G., and Gutler, M. E. (1959). “Further studies of the properties of London clay.” Geotechnique, 9(2), 321–344.
Zienkiewicz, O. C., and Taylor, R. L. (1989). “The finite-element method.” Basic formulation and linear problems, 4th Ed., Vol. 1, McGraw-Hill, London.
Zienkiewicz, O. C., Valliappan, S., and King, I. P. (1968). “Stress analysis of rock as a no tension material.” Geotechnique, 18, 56–66.
Information & Authors
Information
Published In
Copyright
© 2006 ASCE.
History
Received: May 5, 2004
Accepted: Dec 7, 2004
Published online: Jun 1, 2006
Published in print: Jun 2006
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.