Serviceability Reliability of Reinforced Concrete Beams with Corroded Reinforcement
Publication: Journal of Structural Engineering
Volume 135, Issue 8
Abstract
To date, attention of researchers concentrated mainly on the serviceability failure of corroded reinforced concrete (RC) beams caused by excessive cracking. However, cracking of the concrete cover and a reduction in the bond strength (which may result in slip between the corroding reinforcement and the concrete) also decrease the stiffness of RC beams. As a result of it, displacements of the RC beams increase and may exceed a limit value specified in a code, i.e., it has been noted that corrosion may also cause the serviceability failure due to excessive displacements. In this paper the effect of corrosion on deflections of RC beams and, subsequently, on the probability of serviceability failure due to excessive deflection is considered. A nonlinear finite element model is used to describe the structural behavior of RC beams with corroding reinforcement. Uncertainties associated with the model and available data are taken into account. Results show that an increase in deflections due to corrosion has a lesser effect on serviceability of RC beams than corrosion-induced cracking.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abdul Razak, H., and Choi, F. C. (2001). “The effect of corrosion on the natural frequency and modal damping of reinforced concrete beams.” Eng. Struct., 23(9), 1126–1133.
Almusallam, A. A., Al-Gahtani, A. S., Aziz, A. R., and Rasheeduzzafar. (1996). “Effect of reinforcement corrosion on bond strength.” Constr. Build. Mater., 10(2), 123–129.
Alonso, C., Andrade, C., Rodriguez, J., and Diez, J. M. (1998). “Factors controlling cracking of concrete affected by reinforcement corrosion.” Mater. Struct., 31(211), 435–441.
Al-Sulaimani, G. J., Kaleemullah, M., Basumbul, I. A., and Rasheeduzzafar. (1990). “Influence of corrosion and cracking on bond behavior and strength of reinforced concrete members.” ACI Struct. J., 87(2), 220–231.
American Concrete Institute (ACI). (2005). “Building code requirements for structural concrete.” ACI 318-05, Detroit.
Auyeung, Y., Balaguru, P., and Chung, L. (2000). “Bond behavior of corroded reinforcement bars.” ACI Mater. J., 97(2), 214–220.
Barzegar, F., and Schnobrich, W. C. (1990). “Post-cracking analysis of reinforced concrete panels including tension stiffening.” Can. J. Civ. Eng., 17(3), 311–320.
Bentur, A., Diamond, S., and Berke, N. S. (1997). Steel corrosion in concrete, E & FN Spon, London.
Cabrera, J. G., and Ghoddoussi, P. (1992). “The effect of reinforcement corrosion on the strength of the steel/concrete bond.” Proc., Int. Conf. Bond in Concrete, CEB, Riga, Latvia, 10-11–10-24.
Castel, A., Francois, R., and Arliguie, G. (2000). “Mechanical behaviour of corroded reinforced concrete beams. Part 1: Experimental study of corroded beams.” Mater. Struct., 33(233), 539–544.
Chalk, P. L., and Corotis, R. B. (1980). “Probability models for design live loads.” J. Struct. Div., 106(10), 2017–2033.
Ciampi, V., Eligehausen, R., Bertero, V. V. and Popov, E. P. (1981). “Analytical model for deformed bar bond under generalized excitations.” Trans. IABSE Colloquium on Advanced Mechanics of Reinforced Concrete, IABSE, Zurich, Switzerland.
Comité Euro-International du Béton (CEB). (1993). “CEB-FIP Model Code 1990.” CEB Bulletin d’Information 213/214, Lausanne, Switzerland.
Coronelli, D., and Gambarova, P. (2004). “Structural assessment of corroded reinforced concrete beams: Modeling guidelines.” J. Struct. Eng., 130(8), 1214–1224.
DuraCrete. (2000). Final Technical Report: General Guidelines for Durability Design and Redesign, Document BE95–1347/R17, The European Union—Brite EuRam III.
Ellingwood, B. R., Galambos, T. V., MacGregor, J. G., and Cornell, C. A., “Development of a probability based load criterion for American National Standard A58.” National Bureau of Standards Special Publication 577, U.S. Government Printing Office, Washington, D.C.
El Maaddawy, T., Soudki, K., and Topper, T. (2005). “Long-term performance of corrosion-damaged reinforced concrete beams.” ACI Struct. J., 102(5), 649–656.
International Organization for Standardization (ISO). (1998). “General principle on reliability for structures.” ISO 2394, Geneva.
Koch, G. H., Brongers, M. P. H., Thomson, N. G., Virmani, Y. P., and Payer, J. H. (2001). “Corrosion costs and preventive strategies in the United States.” Rep. No. FHWA-RD-01-156, Federal Highway Administration, Washington, D.C.
Li, C. Q., and Zheng, J. J. (2005). “Propagation of reinforcement corrosion in concrete and its effects on structural deterioration.” Mag. Concrete Res., 57(5), 261–271.
Liu, Y., and Weyers, R. E. (1998). “Modelling the time-to-corrosion cracking in chloride contaminated reinforced concrete structures.” ACI Mater. J., 95(6), 675–681.
Mangat, P. S., and Elgarf, M. S. (1999). “Bond characteristics of corroding reinforcement in concrete beams.” Mater. Struct., 32(216), 89–97.
Melchers, R. E. (1999). Structural reliability: Analysis and prediction, 2nd Ed., Wiley, Chichester, England.
Mirza, S. A., and MacGregor, J. G. (1979). “Variability of mechanical properties of reinforcing bars.” J. Struct. Div., 105(5), 921–937.
Nowak, A. S., Szerszen, M. M., Szeliga, E. K., Szwed, A., and Podhorecki, P. J. (2005). “Reliability-based calibration for structural concrete.” Rep. No. UNLCE 05-03, Univ. of Nebraska, Lincoln, Neb.
Philpot, T. A., Rosowsky, D. V., and Fridley, K. J. (1993). “Serviceability design in LRFD for wood.”J. Struct. Eng., 119(12), 3649–3667.
Rodriguez, J., Ortega, L. M., Casal, J. and Diez, J. M. (1996). “Assessing structural conditions of concrete structures with corroded reinforcement.” Concrete repair, rehabilitation and protection, R. K. Dhir and M. R. Jones, eds., E & FN Spon, London, 65–78.
Rodriguez, J., Ortega, L., and Garcia, A. (1994). “Corrosion of reinforcing bars and service life of R/C structures: Corrosion and bond deterioration.” Proc., Int. Conf. on Concrete across Borders, Odense, Denmark, 315–326.
Salawu, O. S. (1997). “Detection of structural damage through changes in frequency: A review.” Eng. Struct., 19(9), 718–723.
Soudki, K., and Sherwood, T. (2003). “Bond behavior of corroded steel reinforcement in concrete wrapped with carbon fiber reinforced polymer sheets.” J. Mater. Civ. Eng., 15(4), 358–370.
Stewart, M. G. (1996). “Serviceability reliability analysis of reinforced concrete structures.” J. Struct. Eng., 122(7), 794–803.
Thoft-Christensen, P. (2005). “Service life definitions based on corrosion crack width.” Proc., 9th Int. Conf. on Structural Safety and Reliability, Rome, 2005 (CD-ROM), G. Augusti, G. I. Schuëller, and M. Ciampolli, eds., Millpress, Rotterdam.
Torres-Acosta, A. A., Fabela-Gallegos, M. J., Munoz-Noval, A., Vazquez-Vega, D., Hernandez-Jimenez, J. R., and Martinez-Madrid, M. (2004). “Influence of corrosion on the structural stiffness of reinforced concrete beams.” Corrosion (Houston), 60(9), 862–872.
Val, D., Bljuger, F., and Yankelevsky, D. (1997). “Reliability evaluation in nonlinear analysis of reinforced concrete structures.” Struct. Safety, 19(2), 203–217.
Val, D. V. (2005). “Effect of different limit states on life-cycle cost of RC structures in corrosive environment.” J. Infrastruct. Syst., 11(4), 231–240.
Vidal, T., Castel, A., and Francois, R. (2004). “Analyzing crack width to predict corrosion in reinforced concrete.” Cem. Concr. Res., 34(1), 165–174.
Vu, K., Stewart, M. G., and Mullard, J. (2005). “Corrosion-induced cracking: Experimental data and predictive models.” ACI Struct. J., 102(5), 719–726.
Williamson, S., and Clark, L. A. (2002). “Effect of corrosion and load on reinforcement bond strength.” Struct. Eng. Int. (IABSE, Zurich, Switzerland), 12(2), 117–122.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Mar 27, 2007
Accepted: Feb 9, 2009
Published online: Jul 15, 2009
Published in print: Aug 2009
Notes
Note. Associate Editor: Sankaran Mahadevan
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.