Three-Stage Full-Range Stress-Strain Model for Stainless Steels
Publication: Journal of Structural Engineering
Volume 134, Issue 9
Abstract
Advanced numerical modeling of cold-formed stainless steel members, from manufacturing to full-range response under applied loading, requires knowledge of the stress-strain relationship of the material over a wide range of tensile and compressive strains. Although a number of stress-strain models have been developed for stainless steels, they are only capable of accurate predictions either over a limited strain range or for the tensile stress-strain behavior only. This paper presents a three-stage stress-strain model for stainless steels, which is capable of accurate predictions over the full ranges of both tensile and compressive strains. The new stress-strain model is defined using the three basic Ramberg-Osgood parameters and is based on a careful interpretation of existing experimental data. The accuracy of the proposed model is demonstrated by comparing its predictions with experimental stress-strain curves. These comparisons also clearly demonstrate the advantage of the proposed model over the only existing full-range stress-strain model.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The writers would like to thank The Hong Kong Polytechnic University (Project No. G-V864), the University of Macau (Ref. No. RG070/05-06S/QWM/FST), and the Research Grants Council of the Hong Kong S.A.R. (Project No. PolyU5056/02E) for their financial support.
References
ASCE. (2002). “Specification for the design of cold-formed stainless steel structural members.” SEI/ASCE 8-02, American Society of Civil Engineers, Reston, Va.
AS/NZS. (2001). “Cold-formed stainless steel structures.” AS/NZS 4673:2001, Australian/New Zealand Standard, Standards Australia, Sydney.
ASTM. (2003). “Standard practice for numbering metals and alloys (UNS).” ASTM E527-83, American Society for Testing and Materials, West Conshohocken, Pa.
BSI. (1995). “Stainless steels—Part 1: List of stainless steels.” BS EN 10088-1, British Standards Institution, U.K.
Chakrabarty, J. (2000). Applied plasticity, Springer, New York.
Chen, J., and Young, B. (2006). “Stress-strain curves for stainless steel at elevated temperatures.” Eng. Struct., 28, 229–239.
Cottrell, A. H. (1964). The mechanical properties of matter, Wiley, New York.
Davis, H. E., Troxell, G. E., and Hauck, G. F. W. (1982). The testing of engineering materials, 4th Ed., McGraw-Hill, New York.
Gardner, L., and Ashraf, M. (2006). “Structural design for nonlinear metallic materials.” Eng. Struct., 28, 926–934.
Gardner, L., and Nethercot, D. A. (2004a). “Experiments on stainless steel hollow sections. Part 1: Material and cross-sectional behaviour.” J. Constr. Steel Res., 60, 1291–1318.
Gardner, L., and Nethercot, D. A. (2004b). “Numerical modeling of stainless steel structural components—A consistent approach.” J. Struct. Eng., 130(10), 1586–1601.
Gardner, L., and Nethercot, D. A. (2004c). “Stainless steel structural design: A new approach.” Struct. Eng., 82(21), 21–28.
Haldar, A., and Mahadevan, S. (2000). Probability, reliability and statistical methods in engineering design, Wiley, New York.
Kalpakjian, S. (1991). Manufacturing processes for engineering materials, 2nd Ed., Addison-Wesley, Reading, Mass.
Korvink, S. A., Van der Berg, G. J., and Van der Merwe, P. (1995). “Web crippling of stainless steel cold-formed beams.” J. Constr. Steel Res., 34, 225–248.
Macdonald, M., Rhodes, J., and Taylor, G. T. (2000). “Mechanical properties of stainless steel lipped channels.” Proc., 15th Int. Specialty Conf. on Cold-Formed Steel Structures, Univeristy of Missouri-Rolla, Mo., 673–686.
Mirambell, E., and Real, E. (2000). “On the calculation of deflections in structural stainless steel beams: An experimental and numerical investigation.” J. Constr. Steel Res., 54, 109–133.
Olsson, A. (2001). “Stainless steel plasticity—Material modelling and structural applications.” Ph.D. thesis, Division of Steel Structures, Dept. of Civil and Mining Engineering, Luleå Univ. of Technology, Sweden.
Quach, W. M. (2005). “Residual stresses in cold-formed steel sections and their effect on column behaviour.” Ph.D. thesis, Dept. of Civil and Structural Engineering, Hong Kong Polytechnic Univ., Hong Kong.
Quach, W. M., Teng, J. G., and Chung, K. F. (2006). “Finite-element predictions of residual stresses in press-braked thin-walled steel sections.” Eng. Struct., 28, 1609–1619.
Rasmussen, K. J. R. (2003). “Full-range stress-strain curves for stainless steel alloys.” J. Constr. Steel Res., 59, 47–61.
Rasmussen, K. J. R., Burns, T., Bezkorovainy, P., and Bambach, M. R. (2002). “Numerical modelling of stainless steel plates in compression.” Research Rep. No. R813, Dept. of Civil Engineering, Univ. of Sydney, Sydney, Australia.
Rasmussen, K. J. R., Burns, T., Bezkorovainy, P., and Bambach, M. R. (2003). “Numerical modelling of stainless steel plates in compression.” J. Constr. Steel Res., 59, 1345–1362.
Steel Construction Institute (SCI). (1991). “Tests on stainless steel materials.” Report No. SCI-RT-251, Steel Construction Institute, London.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Jun 19, 2007
Accepted: Jan 28, 2008
Published online: Sep 1, 2008
Published in print: Sep 2008
Notes
Note. Associate Editor: Kim J. R. Rasmussen
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.