Direct Analysis and Design of Steel Frames Accounting for Partially Restrained Column Base Conditions
Publication: Journal of Structural Engineering
Volume 134, Issue 9
Abstract
The 2005 AISC specification provides a new method for stability design of steel frame structures termed the direct analysis method (DM). This paper addresses the consideration of partial base fixity using the DM. A refined model of the column base moment-rotation response is developed using an adaptation of the component method (CM) of Eurocode 3 plus a representation of the foundation stiffness. The paper also summarizes and applies an extension of the DM for frames containing web-tapered members. An example clear-span gable frame is checked using several models of its nominally simple four-bolt base detail: ideally pinned, elastic based on from the AISC sidesway-uninhibited alignment chart, and elastic-perfectly plastic using the CM. It is demonstrated that the member strength unity checks and the frame deflections obtained by modeling of the column bases as elastic based on are accurate to slightly optimistic compared to the refined base model. It is found that the contribution of the significant initial stiffness of typical bases to the overall frame response is limited by the connection strength.
Get full access to this article
View all available purchase options and get full access to this article.
References
AISC. (1961). Steel construction manual, American Institute of Steel Construction, New York.
AISC. (2005a). Code of standard practice for steel buildings and bridges, American Institute of Steel Construction, Inc., Chicago.
AISC. (2005b). “Specification for structural steel buildings.” ANSI/AISC 360-05, American Institute of Steel Construction, Chicago.
ASCE/SEI. (2005). “Minimum design loads for buildings and other structures.” ASCE/SEI 7-05, American Society of Civil Engineers/Structural Engineering Institute, Reston, Va.
Christopher, J. E., and Bjorhovde, R. (1999). “Semi-rigid frame design methods for practicing engineers.” Eng. J., 36(1), 12–28.
COST. (1999). Column bases in steel building frames, COST C1, European Commission, K. Weynand, ed., Brussels, Belgium.
DeWolf, J. T., and Sarisley, E. F. (1980). “Column base plates with axial loads and moments.” J. Struct. Div., 106(11), 2167–2184.
Eroz, M., White, D. W., and DesRoches, R. (2006). “Direct analysis and design of steel frames accounting for partially-restrained column base conditions.” Structural Engineering, Mechanics and Materials Rep. No. 65, School of Civil and Environmental Engineering, Georgia Institute of Technology, Atlanta.
Eurocode. (1998). “Joints in building frames.” Eurocode, 3, Revised Annex J, CEN, Document ENV 1993-1-1:1992/A2, Brussels, Belgium.
Fisher, J. M., and Kloiber, L. A. (2006). Base plate and anchor rod design, 2nd Ed., Steel Design Guide Series 1, American Institute of Steel Construction, Inc., Chicago.
Galambos, T. V. (1960). “Influence of partial base fixity on frame stability.” J. Struct. Div., 86(5), 85–117.
Griffis, L. G., and White, D. W. (2007). Stability design of steel buildings, Steel Design Guide Series, American Institute of Steel Construction, to appear.
Hon, K. K., and Melchers, R. E. (1987). “Moment-rotation curves for ‘pinned’ column-bases.” Struct. Eng., 65B(3), 54–59.
Kaehler, R. C., White, D. W., and Kim, Y. D. (2007). Frame design using web-tapered members, Steel Design Guide Series, Metal Building Manufacturers Association and American Institute of Steel Construction, to appear.
Lambe, T. W., and Whitman, R. V. (1969). Soil mechanics, Wiley, New York.
Lee, C. G., Ketter, R. L., and Hsu, T. L. (1981). Design of single story rigid frames, Metal Building Manufacturers Association, Cleveland.
Leon, R. T., Hoffman, J. J., and Staeger, T. (1996). Partially restrained composite connections, Steel Design Guide Series 8, American Institute of Steel Construction, Chicago.
Mazzoni, S., McKenna, F., Scott, M. H., Fenves, G. L., and Jeremic, B. O. (2006). Open System for Earthquake Engineering Simulation (Opensees) command language manual.
Melcher, R. E. (1992). “Column-base response under applied moment.” J. Constr. Steel Res., 23, 127–143.
Nogueiro, P., Silva, L., Silvestre, N., and Camotim, D. (2000). “Nonlinear behavior of pitched-roof frames with bilinear semi-rigid connections.” Proc., Structural Stability Research Council, 104–116.
Penserini, P., and Colson, A. (1989). “Ultimate limit strength of column-base connections.” J. Constr. Steel Res., 14, 301–320.
Picard, B., and Beaulieu, D. (1985). “Behavior of a simple column base connection.” Can. J. Civ. Eng., 12, 126–136.
Salmon, C. G., Schenker, L., and Johnston, B. G. (1957). “Moment-rotational characteristics of column anchorages.” Trans. Am. Soc. Civ. Eng., 122, 132–154.
Surovek, A. E., White, D. W., and Leon, R. T. (2005). “Direct analysis for design evaluation of partially restrained steel framing systems.” J. Struct. Eng., 131(9), 1376–1389.
Watwood, V. B. (1985). “Gable frame design considerations.” J. Struct. Eng., 111(7), 1543–1558.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Jun 18, 2007
Accepted: Jan 28, 2008
Published online: Sep 1, 2008
Published in print: Sep 2008
Notes
Note. Associate Editor: Kim J. R. Rasmussen
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.