Ductility and Energy Dissipation Capacity of Shear-Dominated Steel Plate Walls
Publication: Journal of Structural Engineering
Volume 134, Issue 9
Abstract
An experimental study was performed to investigate the potential maximum ductility and energy dissipation capacity of steel plate walls with thin infill plates. Three specimens of a three-story steel plate wall were tested. A concentrically braced frame (CBF) and a moment-resisting frame (MRF) were also tested for comparison. To maximize the ductility and energy dissipation capacity of the steel plate walls, ductile details were used. The test parameters were the aspect ratio of the infill plate and the shear strength of the column. The steel plate walls exhibited much better ductility and energy dissipation capacity as compared to the CBF and MRF. This result indicates that unlike conventional reinforced concrete walls and CBFs, shear-dominated steel plate walls with thin infill plates possess excellent ductility capacity as well as high strength and stiffness. Based on the results of previous studies and the present study, the variations in the ductility and the energy dissipation capacity of the steel plate walls according to the design parameters were investigated.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was financially supported by the Research Institute of Industrial Science and Technology (RIST) and Korea Institute of Construction and Transportation Technology Evaluation and Planning (KICTTEP) (Grant No. UNSPECIFIEDC105A1050001-05A0505-00210), and the writers are grateful to the authorities for their support.
References
AISC. (2005). Seismic provisions for structural steel buildings, AISC, Chicago
Astaneh-Asl, A. (2001). “Seismic behavior and design of steel shear walls.” Steel TIPS Rep., Structural Steel Education Council, Moraga, Calif.
Behbahanifard, M. R. (2003). “Cyclic behavior of unstiffened steel plate shear walls.” Ph.D. dissertation, Dept. of Civil Engineering, Univ of Alberta, Edmonton, Alberta, Canada.
Blogett, O. (1995). “Structural details to increase ductility of connections.” Steel TIPS Rep., Structural Steel Education Council, Moraga, Calif.
Caccese, V., Elgaaly, M., and Chen, R. (1993). “Experimental study of thin steel-plate shear walls under cyclic load.” J. Struct. Eng., 119(2), 573–587.
Canadian Standards Association (CSA). (2001). “Limit states design of steel structures.” CAN/CSA S16-01, Willowdale, Ontario, Canada.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1997). “Seismic behavior of steel plate shear walls.” Structural Engineering Rep. No. 215, Dept. of Civil Engineering, Univ of Alberta, Edmonton, Alberta, Canada.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1998). “Cyclic test of a four-storey steel plate shear wall.” J. Struct. Eng., 124(2), 111–120.
Elgaaly, M. (1998). “Thin steel plate shear walls behavior and analysis.” Thin-Walled Struct., 32, 151–180.
Hibbitt, Karlsson, and Sorenson Inc. (HKS). (2003). ABAQUS standard, version 6.4, Pawtucket, R.I.
Lubell, A. S., Prion, H. G. L., Ventura, C. E., and Rezai, M. (2000). “Unstiffened steel plate shear wall performance under cyclic loading.” J. Struct. Eng., 126(4), 453–460.
Park, H. G., Kwack, J. H., Jeon, S. W., Kim, W. K., and Choi, I. R. (2007). “Framed steel plate wall behavior under cyclic lateral loading.” J. Struct. Eng., 133(3), 378–388.
Information & Authors
Information
Published In
Copyright
© 2008 ASCE.
History
Received: Mar 5, 2007
Accepted: Jan 28, 2008
Published online: Sep 1, 2008
Published in print: Sep 2008
Notes
Note. Associate Editor: Benjamin W. Schafer
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.