Wooden Ship Hulls as Box Girders with Multiple Interlayer Slip
This article has been corrected.
VIEW CORRECTIONPublication: Journal of Structural Engineering
Volume 133, Issue 6
Abstract
The difficulties of modeling the vertical flexure of mechanically fastened wooden ship hulls as that of box beams, a mainstay of naval architecture when applied to iron and steel ships, can largely be overcome by factoring the incomplete composite action of timber components in terms of a reduced shear modulus, an increased shear lag, and a reduced sectional area in tension (owing to butt joints). Sample computations on a large wooden hull indicate that its deflection can be limited to about twice that of a completely composite hull if stiff fasteners (drift pins) are used at a much greater density than is typical of traditional construction. The lengths of timber pieces become severely limiting only if they are below of hull length. The methodology has broad application to the preliminary design of many-piece timber box beam structures in general.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abegg, G. L. (1864). “On the combined system of wood and iron in shipbuilding.” Trans. RINA, 5, 304–315.
American Bureau of Shipping. (1943). Rules for the construction and classification of wooden ships, New York.
Anon. (1867). “Composite ships.” Engineering (London), 359.
Bourne, J. (1855). A treatise on the screw propeller, 2nd Ed., Spottiswoode, London.
Coates, J. F. (1985). “Hogging or breaking of framebuilt wooden ships: A field for investigation?” Mariner’s Mirror, 71, 437–442.
Crowninshield, B. B. (1907). “Wooden sailing ships.” Trans. S.N.A.M.E., 15, 187–199.
Davis, A. (1997). “A cold molded shell for the USS Constellation.” http://www.maritime.org/conf/conf-davis.htm (July 7, 1997).
Dennis, D. L. (1964). “The deficiencies of wooden shipbuilding.” Mariner’s Mirror, 50, 62–63.
Evans, K. G. (1958). “Design of wooden naval vessels.” Trans. RINA, 100, 25–34.
Gerard, G. (1948). “Optimum number of webs required for a multicell box under bending.” J. Aeronaut. Sci., 15, 53–56.
Griffiths, J. W. (1874). The progressive ship builder, Vol. 1, Nautical Gazette Press, New York.
Gutshall, S. T. (1994). “Monotonic and cyclic short-term performance of nailed and bolted timber connections.” MS thesis, Univ. of Virginia, Blacksburg, Va.
Hishida, I., and Mano, H. (1959). “A theoretical study on longitudinal strength of wooden ships.” J. Soc. Nav. Archit. Jpn., 104, 131–137.
Hori, T., Inoue, K., Murata, S., and Majima, Y. (1989). “Longitudinal strength of wooden ships of triple skin planking system.” Hitachi Zosen Gihao, 50(1), 12–20.
Johansen, K. W. (1949). “Theory of timber connections.” Struct. Eng. Int. (IABSE, Zurich, Switzerland), 9, 249–262.
Johnson, A. M. (1954). “Developments in the hull design of wooden ships.” J. Am. Soc. Nav. Eng., 66, 867–878.
Kuhn, P. (1939). “A recurrence formula for shear-lag problems.” National Advisory Committee for Aeronautics (USA) Technical Notes (N.A.C.A. TN) 739.
Kuhn, P. (1947). “Deformation analysis of wing structures.” National Advisory Committee for Aeronautics (USA) Technical Notes (N.A.C.A. TN) 361.
Kuhn, P. (1956). Stresses in aircraft and shell structures, McGraw-Hill, New York.
LaCross, V. D., Manbeck, H. B., Witmer, R. W., Jr., Laman, J. A., and Janowiak, J. J. (2000). “Endurance of deck-to-deck connections in transverse hardwood glulam decks.” J. Bridge Eng., 5(1), 84–89.
Lamport, C. (1864). “On wood and iron ships.” Trans. RINA, 5, 287–303.
Lopez-Anido, R. (1995). “Analysis and design of orthotropic plates stiffened by laminated beams for bridge superstructures.” Ph.D. dissertation, Univ. of West Virginia, Va.
Milner, H. R., and Tan, H. H. (2001). “Modeling deformation in nailed, thin-webbed timber box beams.” Comp. Struct., 79, 2541–2546.
Newlin, J. A., and Trayer, G. W. (1924). “Deflection of beams with special reference to shear deformations.” N.A.C.A. Rep. No. 180.
Oden, J. T., and Ripperger, E. A. (1981). Mechanics of elastic structures, 2nd Ed., Hemisphere, Washington.
Rankine, W. J. M. (1866). Shipbuilding, theoretical, and practical, William MacKenzie, London.
Reissner, E. (1940). “The influence of taper on the efficiency of wide flanged box beams.” J. Aeronaut. Sci., 7(8), 353–357.
Reissner, E. (1946). “Analysis of shear lag in box beams by the principle of minimum potential energy.” Q. Appl. Math., 4(3), 268–278.
Saksena, G. B. (1944). “Shear stress in a tapering beam.” Aircr. Eng., 16, 47–49.
Spaulding, K. B., and Della Rocca, R. J. (1965). “Fiberglass-reinforced plastic minesweepers.” Trans. S.N.A.M.E., 73, 415–444.
Squier, H. (1877). Heber Squier’s new method of fastening and strengthening wooden ships, Grand Haven, Mich.
Wetherell, P. W., Ross, R. J., and Faris, W. R. (1992). “Using today’s technology to help preserve the USS Constitution.” Nav. Eng. J., 124–134.
Zahn, J. (1972). “Shear stiffness of two-inch wood decks for roof systems.” U.S.D.A. Forest Service Research Paper FPL 155.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Mar 9, 2006
Accepted: Oct 9, 2006
Published online: Jun 1, 2007
Published in print: Jun 2007
Notes
Note. Associate Editor: J. Daniel Dolan
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.