Seismic Assessment of Concentrically Braced Steel Frames with Shape Memory Alloy Braces
Publication: Journal of Structural Engineering
Volume 133, Issue 6
Abstract
The use of special concentrically braced frames has increased since the 1994 Northridge and 1995 Hyogoken–Nanbu Earthquakes. However, past performance suggests limited ductility and energy dissipation in braced frame systems due to buckling of conventional braces. In order to address this limitation, three- and six-story concentrically braced frames with superelastic shape memory alloy (SMA) braces are studied to evaluate their seismic performance in comparison to traditional systems. SMAs are unique metallic alloys that have the ability to undergo large deformations while reverting back to their original undeformed shape providing recentering capabilities to the braced frame. Detailed analytical models of the frames with SMA braces are developed and two suites of ground motions are used to evaluate the structures with respect to interstory drift and residual drift. The results suggest that the SMA braces are effective in limiting interstory drifts and residual drifts during an earthquake, in part, due to the recentering nature of superelastic SMAs.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study has been supported primarily by the CAREER Program of the National Science Foundation under Grant No. 0093868. Davide Fugazza would like to acknowledge the financial support of the Italian National Civil Protection Department, which through its Servizio Sismico Nazionale Section, provided a scholarship. The findings and conclusions of this paper, however, are those of the writers alone.
References
Andrawes, B. (2005). “Seismic response and analysis of multiple frame bridges using superelastic shape memory alloys.” Ph.D. dissertation, Georgia Institute of Technology, Atlanta.
Andrawes, B., and DesRoches, R. (2005). “Unseating prevention for multiple frame bridges using superelastic devices.” Smart Mater. Struct., 14(3), S60–S67.
Andrawes, B., McCormick, J., and DesRoches, R. (2004). “Effect of cyclic modeling parameters on the behavior of shape memory alloys for seismic applications.” Proc. SPIE, 5390, 324–334.
Auricchio, F., and Sacco, E. (1997). “A one-dimensional model for superelastic shape-memory alloys with different properties between martensite and austenite.” Int. J. Non-Linear Mech., 32(6), 1101–1114.
Baratta, A., and Corbi, O. (2002). “On the dynamic behavior of elastic-plastic structures equipped with pseudoelastic SMA reinforcements.” Comput. Mater. Sci., 25(1–2), 1–13.
Bruno, S., and Valente, C. (2002). “Comparative response analysis of conventional and innovative seismic protection strategies.” Earthquake Eng. Struct. Dyn., 31(5), 1067–1092.
DesRoches, R., McCormick, J., and Delemont, M. (2004). “Cyclic properties of superelastic shape memory alloy wires and bars.” J. Struct. Eng., 130(1), 38–46.
Dolce, M., and Cardone, D. (2001). “Mechanical behavior of shape-memory alloys for seismic applications. 2: Austenite wires subjected to tension.” Int. J. Mech. Sci., 43(11), 2657–2677.
Dolce, M., Cardone, D., and Marnetto, R. (2000). “Implementation and testing of passive control devices based on shape-memory alloys.” Earthquake Eng. Struct. Dyn., 29(7), 945–968.
Duerig, T. W., Melton, K. N., and Wayman, C. M. (1990). Engineering aspects of shape memory alloys, Butterworth-Henemann, London.
Federal Emergency Management Agency (FEMA). (2000). “Recommended seismic design provisions for new moment frame buildings.” Rep. No. FEMA 350, Washington, D.C.
Frick, C. P., Ortega, A. M., Tyber, J., Gall, K., and Maier, H. J. (2004). “Multiscale structure and properties of cast and deformation processed polycrystalline shape-memory alloys.” Metall. Mater. Trans. A, 35A(7), 2013–2025.
Fugazza, D. (2003). “Shape-memory alloy devices for earthquake engineering: Mechanical properties, constitutive modelling and numerical simulations.” Master’s thesis, European School for Advanced Studies in Reduction of Seismic Risk, Pavia, Italy.
Fukuta, T., Iiba, M., Kitagawa, Y., and Sakai, Y. (2004). “Experimental study on stress-strain property of shape memory alloy and its application to self-restoration of structural members.” Proc., 13th World Conf. of Earthquake Engineering, Canadian Association for Earthquake Engineering, Ottawa, Paper 610.
Hamburger, R. O., Foutch, D. A., and Cornell, C. A. (2003). “Translating research to practice: FEMA/SAC performance-based design procedures.” Earthquake Spectra, 19(2), 255–267.
Han, Y.-L., Li, Q. S., Li, A.-Q., Leung, A. Y. T., and Ling, P.-H. (2003). “Structural vibration control by shape-memory alloy damper.” Earthquake Eng. Struct. Dyn., 32(3), 483–494.
Li, H., Liu, M., and Ou, J. (2004). “Vibration mitigation of a stay cable with one shape memory alloy damper.” Structural Control and Health Monitoring, 11(1), 21–36.
Masuda, A., Sone, A., Kamata, S., and Yamashita, Y. (2004). “Finite-element analysis of shape memory alloy springs designed for base isolation devices.” Proc. SPIE, 5383, 103–111.
McCormick, J., Barbero, L., and DesRoches, R. (2005). “Effect of mechanical training on the properties of superelastic shape memory alloys for seismic applications.” Proc. SPIE, 5764, 430–439.
McKenna, F., and Fenves, G. L. (2004). OpenSees command language manual, version 1.5.2, Pacific Earthquake Engineering Research Center, http://opensees.berkeley.edu (May 2004).
Nakashima, M., Inoue, K., and Tada, M. (1998). “Classification of damage to steel buildings observed in the 1995 Hyogoken-Nanbu Earthquake.” Eng. Struct., 20(4–6), 271–281.
Nakashima, M., Roeder, C. W., and Maruoka, Y. (2000). “Steel moment frames for earthquakes in United States and Japan.” J. Struct. Eng., 126(8), 861–868.
Ocel, J., et al. (2004). “Steel beam-column connections using shape memory alloys.” J. Struct. Eng., 130(5), 732–740.
Sabelli, R. (2001). “Research on improving the design and analysis of earthquake-resistant steel-braced frames: The 2000 National Earthquake Hazard Reduction Program (NEHRP).” Professional Fellowship Rep., Earthquake Engineering Research Institute, Oakland, Calif.
Sabelli, R., Mahin, S., and Chang, C. (2003). “Seismic demands on steel braced frame buildings with buckling-restrained braces.” Eng. Struct., 25(5), 655–666.
Sabol, T. A. (2004). “An assessment of seismic design practice of steel structures in the United States since the Northridge Earthquake.” Struct. Des. Tall Build., 13(5), 409–423.
Somerville, P., Smith, N., Punyamurthula, S., and Sun, J. (1997). “Development of ground motion time histories for phase 2.” SAC background document no. SAC-BD-97-04, SAC Joint Venture, Sacramento, Calif.
Taftali, B., Ellingwood, B. R., and DesRoches, R. (2004). “Fragility of steel moment frames with novel beam-to-column connections utilizing shape memory alloys.” Proc., 9th ASCE Joint Specialty Conf. on Probabilistic Mechanics and Structural Reliability, ASCE, Reston, Va.
Tamai, H., Kitagawa, Y., and Fukuta, T. (2004). “Application of SMA rods to exposed-type column bases in smart structural systems.” Proc., 13th World Conf. of Earthquake Engineering, Canadian Association for Earthquake Engineering, Ottawa, Paper 1884.
Wilde, K., Gardoni, P., and Fujino, Y. (2000). “Base isolation system with shape memory alloy device for elevated highway bridges.” Eng. Struct., 22(3), 222–229.
Information & Authors
Information
Published In
Copyright
© 2007 ASCE.
History
Received: Sep 16, 2005
Accepted: Nov 28, 2006
Published online: Jun 1, 2007
Published in print: Jun 2007
Notes
Note. Associate Editor: Marvin W. Halling
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.