Fatigue Performance of Cracked Tubular T Joints under Combined Loads. I: Experimental
This article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 130, Issue 4
Abstract
Experimental fatigue tests were carried out on three tubular T joints having the same geometrical parameters subjected to in-plane bending (IPB) only, combination of IPB and out-of-plane bending (OPB), and a combination of axial loading, IPB and OPB respectively. Static tests were first carried out to investigate the Hot Spot Stress (HSS) distribution along the intersection of chord and brace, and to determine the peak HSS and its location when the joints were subjected to these load cases. The peak HSS location was used to determine the placement of the probes. An alternating current potential drop technique was then employed to monitor the crack growth and crack shape development on the joints at a preset number of cycles. The experimental data were recorded, and the fatigue performance of the three T joints subjected to basic and combined load cases were investigated. The crack growth curves and crack growth rate on each specimen were presented. The results confirmed that the United Kingdom Department of Energy tubular joint fatigue design T curve derived from a single axis test data is conservative even for combined load cases.
Get full access to this article
View all available purchase options and get full access to this article.
References
American Petroleum Institute (API). (1993). “Recommended practice for planning, designing, and constructing fixed offshore platforms,” API RP2A-LRFD, Washington D.C.
American Welding Society (AWS). (1996). “Structural welding code—Steel.” ANSI/AWS D1.1-96. American Welding Society, Inc., Miami.
Dover, W. D., Dharmavasan, S., Brennan, F. P., and Marsh, K. J. (1995). “Fatigue crack growth in offshore structures.” Engineering Materials Advisory Services (EMAS) Ltd., Chameleon Press, London.
Efthymiou, M., and Durkin, S. (1985). “Stress concentrations in T/Y and gap/overlap K joints.” Proc., Int. Conf., Behavior of Offshore Structures, Delft, The Netherlands, 429–441.
Gulati, K. C., Wang, W. J., and Kan, D. K. Y. (1982). “An analytical study of stress concentration effects in multibrace joints under combined loading.” Proc. 14th Annual Offshore Technology Conf., OTC 4407, Houston, 337–355.
Hellier, A. K., Connolly, M. P., Karé, R. F., and Dover, W. D.(1990). “Prediction of the stress distribution in tubular Y- and T joints.” Int. J. Fatigue, 12(1), 25–33.
International Institute of Welding (IIW). (1999). Recommended fatigue design procedure for hollow section joints. I: Recommendations. International Institute of Welding Subcommission XV-E, IIW Doc. XV-1035-99, IIW Doc. XV-E-99-251, IIW Doc. XIII-1804-99, IIW Assembly, Strasbourg, France.
Schumacher, A., Nussbaumer, A., and Hirt, M. A. (2001). “Fatigue behavior of welded circular hollow section joints in bridges.” Proc., Tubular Structures IX (IDECT and IIW, Madrid, Spain, 291–297.
Smedley, P., and Fisher, P. (1991). “Stress concentration factors for simple tubular joints.” Proc., 1st Int. Offshore and Polar Engineering Conf., International Society of Polar and Offshore Engineers (ISOPE), Edinburgh, U.K., 475–483.
Stacy, A., and Sharp, J. V. (1997). “Fatigue damage in offshore structures—Cause, detection, and repair.” Proc., 8th Int. Conf. on the Behaviour of Offshore Structure, Delft University of Technology, Delft, The Netherlands.
Technical Software Consultant Ltd. (TSC). (1991). ACFM Crack Microgauge—Model U10 User Manual, Milton Keynes, UK.
Technical Software Consultant Ltd. (TSC). (1998). FLAIR User Manual—Software Version 1.9, The Open University, Milton Keynes, UK.
Underwater Engineering Group (UEG). (1985). Design of tubular joints for offshore structures, Vol. 1, Publication UR 33, Underwater Engineering Group, U.K.
United Kingdom Department of Energy (UK DEn). (1993). “Background to new fatigue design guidance for steel joints in offshore structures.” Department of Energy, London.
Wylde, J. G., and McDonald, A. (1979). “The influence of joint dimensions on the fatigue strength of welded tubular joints.” Proc., 2nd Int. Conf., Behavior of Offshore Structures, BHRA Fluid Engineering, Cranfield, U.K., Paper 42, 535–500.
Yeoh, S. K., Soh, A. K., and Soh, C. K.(1995). “Behaviour of tubular T joints subjected to combined loading.” J. Constr. Steel Res., 32, 259–280.
Zhao, X. L., Herion, S., Packer, J. A., Puthli, R., Sedlacek, G., Wardenier, J., Weynand, K., van Wingerde, A., and Yeomans, N. (2000). Design guide for circular and rectangular hollow section joints under fatigue loading, CIDECT, TUV.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Oct 18, 2002
Accepted: May 5, 2003
Published online: Mar 15, 2004
Published in print: Apr 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.