Fatigue Performance of Cracked Tubular T Joints under Combined Loads. II: Numerical
This article is a reply.
VIEW THE ORIGINAL ARTICLEPublication: Journal of Structural Engineering
Volume 130, Issue 4
Abstract
In practice, tubular joints are always subjected to a combination of axial loading (AX), in-plane bending (IPB), and out-of-plane bending (OPB), and the initiation of surface cracks does not always start at the saddle or the crown position on the joints. A systematic finite element modeling of tubular Y joints with any surface crack and located at any position along the brace–chord intersection is developed and proposed in this paper. The weld details in the model conform to the American Welding Society codes. The contact surfaces have been defined carefully between the two crack surfaces that may arise due to some loading cases. Along the crack tip, a well-graded finite element mesh is generated to get the stress intensity factors. This modeling method is then used to analyze three tubular T joint specimens which were tested to failure earlier, and they were subjected to IPB only, combination of IPB and OPB, and a combination of AX, IPB, and OPB, respectively. The numerical results compared favorably with the experimental results based on the Paris’ law, and all of these results demonstrate that the proposed model is consistent and reliable.
Get full access to this article
View all available purchase options and get full access to this article.
References
ABAQUS theory manual, version 6.2. (2001a). Hobbit, Karlsson, and Sorensen Inc., Dallas.
ABAQUS user manual, version 6.2. (2001b). Hobbit, Karlsson, and Sorensen Inc., Dallas.
American Welding Society (AWS). (1996). “Structural welding code— Steel.” ANSI/AWS D1.1-96, American Welding Society, Inc., Miami.
Bowness, D., and Lee, M. M. K.(1995). “The development of an accurate model for the fatigue assessment of doubly curved cracks in tubular joints.” Int. J. Fract., 73, 129–147.
Burdekin, F. M., Chu, W. H., Chan, W. T. W., and Manteghi, S. (1986). “Fracture mechanics analysis of fatigue crack propagation in tubular joints.” International Conference on Fatigue and Crack Growth in Offshore Structures, IMechE, London, UK, C141/86.
Cao, J. J., Yang, G. J., Packer, J. A., and Burdekin, F. M.(1998). “Crack modeling in finite element analysis of circular tubular joints.” Eng. Fract. Mech., 5(6), 537–553.
Chiew, S. P., Lie, S. T., and Huang, Z. W. (2002). “Multiaxes fatigue tests of tubular T joints under complex loads.” Proc., 12th Int. Offshore and Polar Engineering Conf. (ISOPE 2002), Kitakyushu, Japan, International Society of Polar and Offshore Engineers (ISOPE).
Chiew, S. P., Lie, S. T., Lee, C. K., and Huang, Z. W. (2001). “Stress intensity factors of through-thickness and surface cracks in tubular joints.” Proc., 11th Int. Offshore and Polar Engineering Conf. (ISOPE 2001), Stavanger, Norway, International Society of Polar and Offshore Engineers (ISOPE), Vol. IV, 30–34.
Chiew, S.-P., Lie, S.-T., Lee, C.-K., and Huang, Z.-W.(2004). “Fatigue performance of cracked tubular T joints under combined loads. I: Experimental.” J. Struct. Eng., 130(4), 562–571.
Chong Rhee, H., Han, S., and Gipson, G. S. (1991). “Reliability of solution method and empirical formulas of stress intensity factors for weld toe cracks of tubular joints.” Proc., 10th Offshore Mechanics and Arctic Engineering Conference, ASME, Vol. 3-B, 441–452.
Dover, W. D., and Connolly, M. (1986). “Fatigue fracture mechanics assessment of tubular welded Y and K joints.” Proc., Int. Conf., on Fatigue and Crack Growth in Offshore Structure, April, Institute of Mechanical Engineers, IMechE, London, C141/86.
Du, Z. Z., and Hancock, J. W.(1987). “Stress intensity factors of curved semi-elliptical cracks in a tubular welded joint using line springs and three-dimensional finite elements.” J. Pressure Vessel Technol., 111, 247.
Haswell, J.(1991). “Simple models for predicting stress intensity factors for tubular joints.” Fatigue Fract. Eng. Mater. Struct., 14(5), 499–513.
Haswell, J., and Hopkins, P.(1991). “A review of fracture mechanics models of tubular joints.” Fatigue Fract. Eng. Mater. Struct., 14(5), 483–497.
Herion, S., Mang, F., and Puthli, R. (1996). “Parametric study on multiplanar K joints with gap made of circle hollow sections by means of the finite element method.” Proc., 6th Int. Offshore and Polar Engineering Conf., Los Angeles, Vol. IV, 68–73.
Huang, X., and Hancock, J. W.(1988). “The stress intensity factors of semi-cracks in a tubular welded T joint under axial loading.” Eng. Fract. Mech., 1, 25–35.
Kajimoto, K., Fijishima, K., Nawata, T., Takashiria, H., Hagiwan, Y., and Haze, T. (1985). “Brittle fracture strength of tubular joints used in offshore structures.” Proc., 4th Int. Conf., Offshore Mechanics and Arctic Engineering, Dallas.
Lee, C. K., Lie, S. T., and Wong, S. M. (1999). “Model and mesh generation of cracked tubular joints.” Proc., European Conf., Computational Mechanics, Munich, Germany, German Association for Computational Mechanics (GACM), 182–183.
Lee, C. K., Wong, S. M., and Lie, S. T.(2001). “On increasing the order and density of three-dimensional finite element meshes.” Commun. Numer. Methods Eng., 17, 55–68.
Lie, S. T., Chiew, S. P., Lee, C. K., Wong, S. M., and Huang, Z. W. (2000). “Modeling arbitrary through-thickness crack in a tubular T joint.” Proc., 10th Int. Offshore and Polar Engineering Conference (ISOPE 2000), Seattle, Vol. IV, 53–58.
PRETUBE User’s Manual. (1991). Veritas Sesam System, Hovik, Norway: Det Norske Veritas (DNV) Industry Ltd.
Shih, C. F., and Asaro, R. J.(1988). “Elastic–plastic analysis of cracks on bimaterial interfaces. I: Small scale yielding.” J. Appl. Mech., 51, 299–316.
Van Delft, D. R. V., Dijkstra, O. D., and Snijder, H. H. (1986). “The calculation of fatigue crack growth in welded tubular joints using fracture mechanics.” Proc., Offshore Technology Conf., Houston, OTC 5352.
Wong, S. M. (2001). “Model and mesh generation of cracked Y-tubular joints for stress integrity factors and stress concentration factor studies.” MS thesis, Nanyang Technological Univ., Singapore.
Information & Authors
Information
Published In
Copyright
Copyright © 2004 American Society of Civil Engineers.
History
Received: Oct 18, 2002
Accepted: May 5, 2003
Published online: Mar 15, 2004
Published in print: Apr 2004
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.