Reliability of Reused Sawn Lumber: Effect of Fastener Holes
Publication: Journal of Structural Engineering
Volume 127, Issue 4
Abstract
The results of a comprehensive research study on the effect of fastener holes on the reliability of structural timbers, specifically No. 2 Douglas fir 102 × 303 mm (nominal 4 × 8 in.) structural joists and planks, is reported. Through this study, adjustment factors are developed to account for the presence of a hole as a function of its size and location within the member. Such adjustment factors could be used in design by the engineer, or perhaps more appropriately, grading agencies to develop appropriate grading procedures and design values for reused or recycled timbers to ensure acceptable levels of safety. The specific objectives of this paper are, therefore, to (1) quantify and determine the effect of a fastener hole on the reliability of wood beams when various diameter holes are located at various positions throughout the depth; and (2) develop and recommend possible adjustment factors to account for the reduction in reliability created by the presence of a fastener hole. The reduction in reliability caused by a 44.5 mm hole was found not to be significantly different from that caused by a 25.4 mm hole. The reliability, however, is significantly affected by hole location. If the hole is located at the point of maximum moment, the reduction in reliability is over twice as much as when the hole is located randomly within the central third of the length, which is similar to the grading criteria for knots. For a flexural member containing a 25.4–44.5 mm hole anywhere within the central third of the length, the recommended adjustment factor is ω′ = 0.90. In other words, a 10% reduction in design capacity is recommended when such a fastener hole is present in the central third of the member's length.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
American Forest and Paper Association (AF&PA). ( 1997). National design specification (NDS) for wood construction, Washington, D.C.
2.
ASTM. ( 1999a). “Standard practice for establishing allowable properties for visually graded dimension lumber from in-grade tests of full-size specimens.” D 1990, West Conshohocken, Pa.
3.
ASTM. ( 1999b). “Standard practice for establishing structural grades and related allowable properties for visually graded lumber.” D 245, West Conshohocken, Pa.
4.
ASTM. ( 1999c). “Test methods for establishing clear wood strength values.” D 2555, West Conshohocken, Pa.
5.
Bulleit, W. M., Rosowsky, D. V., Fridley, K. J., and Criswell, M. E. (1993). “Reliability of wood structural systems.”J. Struct. Engrg., ASCE, 119(9), 2629–2641.
6.
Ellingwood, B., and Rosowsky, D. V. (1991). “Duration of load effects in LRFD for wood construction.”J. Struct. Engrg., ASCE, 117(2), 584–599.
7.
Falk, R. H. ( 1997). “Wood recycling: Opportunities for the wood waste resource.” Forest Products J., 47(6), 17–22.
8.
Falk, R. H., DeVisser, D. A., and Fridley, K. J. ( 1999). “Developing a grade stamp for recycled timber.” Final Rep., Clean Washington Center, Seattle.
9.
Philphot, T. A., Rosowsky, D. V., and Fridley, K. J. (1995). “Reliability of wood joist floor systems with creep.”J. Struct. Engrg., ASCE, 121(6), 946–954.
10.
Rosowsky, D. V., and Fridley, K. J. (1992). “Moisture content and reliability-based design for wood members.”J. Struct. Engrg., ASCE, 118(12), 3466–3472.
11.
Rosowsky, D. V., and Fridley, K. J. (1997). “Effect of discrete member size on reliability of wood beams.”J. Struct. Engrg., ASCE, 123(6), 831–835.
12.
West Coast Lumber Inspection Bureau (WCLIB). ( 1995). Grading rules for West Coast lumber, Portland, Ore.
13.
Williams, J. M., Fridley, K. J., Cofer, W. F., and Falk, R. H. ( 2000). “Failure modeling of sawn lumber with a fastener hole.” Finite Elements in Anal. and Des., in press.
Information & Authors
Information
Published In
History
Received: Mar 10, 2000
Published online: Apr 1, 2001
Published in print: Apr 2001
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.