Tests to Examine Plastic Behavior of Knee Joints in Cold-Formed RHS
Publication: Journal of Structural Engineering
Volume 126, Issue 3
Abstract
This paper describes tests on various types of knee joints for steel portal frames constructed from cold-formed rectangular hollow sections (RHS) to examine the ability of the connections to form plastic hinges. Welded stiffened and unstiffened knee joints, bolted knee joints with end plates, and connections with a fabricated internal sleeve were included in the experimental investigation. Most connections tested under opening moment failed by fracture in the heat-affected zone of the RHS near the weld. The connections tested under closing moment failed by web local buckling, which occurred near the connection. While the stiffened and unstiffened welded connections satisfied the strength interaction requirements in the available design guides, the connections did not maintain the plastic moment for sufficiently large rotations to be considered suitable for a plastic hinge location. The unstiffened welded joints were not able to reach the plastic moment. The use of an internal sleeve moved the plastic hinge in the connection away from the connection center-line and reduced the stress on the weld between the legs of the connection. It was found that sleeve connections were capable of sustaining the plastic moment for large rotations considered suitable for plastic design.
Get full access to this article
View all available purchase options and get full access to this article.
References
1.
Centre for Advanced Structural Engineering. (1992). “Tests on rectangular hollow sections to investigate the effect of variation of yield stress around a section.” Investigation Rep. S885, School of Civ. and Min. Engrg., University of Sydney, Australia.
2.
“Design of steel structures: Part 1.1—General rules and rules for buildings.” (1992). DD ENV. 1993-1-1, Eur. Com. for Standardisation, Eurocode 3 Editorial Group, Brussels, Belgium.
3.
“High strength steel bolts with associated steel nuts and washers for structural engineering.” (1981). AS 1252, Standards Australia, Sydney, Australia.
4.
Hollow structural sections connections manual. (1997). AISC, Chicago, Ill.
5.
“ISO metric hexagon commercial bolts and screws.” (1981). AS 1111, Standards Australia, Sydney, Australia.
6.
Lay, M. G., and Galambos, T. V. (1965). “Inelastic steel beams under uniform moment.”J. Struct. Div., ASCE, 91(6), 67–93.
7.
Lay, M. G., and Galambos, T. (1967). “Inelastic steel beams under moment gradient.”J. Struct. Div., ASCE, 93(1), 81–99.
8.
Load and resistance factor design specification for the structural steel buildings. (1994). American Institute of Steel Construction, Chicago, Ill. (metric edition).
9.
Mang, F., Herion, S., and Karcher, D. (1997). “L-joints made of circular hollow sections.” Final Rep., CIDECT Project 5BE, Res. Ctr. for Steel, Timber and Masonry, University of Karlsruhe, Germany.
10.
Mang, F., Steidl, G., and Bucak, O. (1980). “Design of welded lattice joints and moment resisting knee joints made of hollow sections.” Document XV-463-80, Int. Inst. of Welding, University of Karlsruhe, Germany.
11.
“Methods for tensile testing of metals.” (1991). AS 1391, Standards Australia, Sydney, Australia.
12.
Packer, J. A., Wardenier, J., Kurobane, Y., Dutta, D., and Yeomans, N. (1992). Design guide for rectangular hollow section (RHS) joints under predominantly static loading. CIDECT Design Guide No. 3, Verlag TÜV Rheinland GmbH, Köln, Germany.
13.
Puthli, R., Herion, S., and Karcher, D. (1998). “L-joints made of RHS and CHS under fatigue.” Second Interim Rep., CIDECT Project 7S, Res. Ctr. for Steel, Timber and Masonry, University of Karlsruhe, Germany.
14.
“Standard specification for cold-formed welded and seamless carbon steel structural tubing in shapes and rounds.” (1993). A 500, ASTM, Philadelphia, PA.
15.
“Steel structures.” (1998). AS 4100, Standards Australia, Sydney, Australia.
16.
“Structural steel hollow sections.” (1991). AS 1163, Standards Australia, Sydney, Australia.
17.
“Structural steel: Hot-rolled structural plates, floorplates and slabs.” (1990). AS 3678, Standards Australia, Sydney, Australia.
18.
“Structural steel welding, Part 1: Welding of steel structures.” (1995). AS/NZS 1554.1, Standards Australia/Standards New Zealand, Sydney, Australia.
19.
Structural welding code—steel; ANSI/AWS D1.1-96. (1996). 14th ed., American Welding Society, Inc., Miami, Fla.
20.
Wilkinson, T., and Hancock, G. J. (1998a). “Tests of knee joints in cold-formed rectangular hollow sections.” Res. Rep. No. R779, Dept. of Civ. Engrg., University of Sydney, Australia.
21.
Wilkinson, T., and Hancock, G. J. (1998b). “Tests to examine the compact web slenderness of cold-formed RHS.”J. Struct. Engrg., ASCE, 124(10), 1166–1174.
22.
Zhao, X. L., and Hancock, G. J. (1995a). “Butt welds and transverse fillet welds in thin cold-formed RHS members.”J. Struct. Engrg., ASCE, 121(11), 1674–1682.
23.
Zhao, X. L., and Hancock, G. J. (1995b). “Longitudinal fillet welds in thin cold-formed RHS.”J. Struct. Engrg., ASCE, 121(11), 1683–1690.
Information & Authors
Information
Published In
History
Received: Jan 6, 1999
Published online: Mar 1, 2000
Published in print: Mar 2000
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.